Installation Guide
PULL TOGGLE
HEAVY DUTY HOLLOW
WALL ANCHOR
Features & Benets
• Heavy Duty Hollow Wall Anchor
• No pre-drilling in drywall, anchor self drills it’s own hole!
• Fast and easy to install
• Replaces toggle bolt anchors
• Common applications include shelving, mirrors, large pictures, mounting
brackets, dry erase boards and more
• For use in drywall, plaster, tile & hollow block applications
• Smaller hole size compared to 3/16 or 1/4 inch toggle bolt anchors
(Pull Toggle 1/2 inch vs. 9/16 or 3/4 inch)
• Faster installation than traditional toggle bolt anchors
• Flat section of the anchor holds behind the wall creating more surface area
and ultimately a stronger anchor
• Other toggle anchors have thin sections of metal behind the wall that
could dig into drywall, weakening the load
• Self-Drilling tip allows you to penetrate 3/8 or 1/2 inch drywall without
pre-drilling.
• The strap and sleeve nut are designed for easy installation with a strong
hold every time.
• The strap has a clean breakaway so there is no debris on the face of the
sleeve nut allowing for a premium installation
• The head of the anchor and the strap are designed with a memory ip
pivot so the anchor is in place once its behind the wall.
• No ipping, adjusting straps or additional installation steps required.
Product Information
• Grip range from 3/8 to 3 inches
• 2 inch grip range with included 2-1/2 inch length screws
• Works in walls up to 3 inches, must use 3-1/2 inch or
longer screws.
• Always use screws at least a 1/2 inch longer than your
grip range.
• Published loads are safe working loads
• These loads are determined from ultimate failure load
testing and considerably reduced for your safety.
• Load values should also be reduced if your weight of
project load will be further away from the wall
• The safe working load was determined with the
anchor ush to the wall.
• Often times with anchors of these types, the wall
materials will fail before the anchor due to improper
installation.
• Please ensure you are anchoring your project
properly and following all manufacturer’s
recommendations for proper installation.
• Many devices will call for securing them directly into
studs, such as tv mounts and other items that hang far
away from the wall. Always follow these directions.
• When anchoring any object to a wall, especially
drywall, follow the manufacturers instructions of the
device you are anchoring carefully.
• Safe working loads are based on 2:1 safety factor
using an average of ultimate shear loads
• For vibration and shock loads, reduce allowable load
by a safety factor of 4.
• Safe working loads are a guide only and cannot be
guaranteed.
• Pound ratings are based on the anchor only.
Effectiveness can be diminished based on the
material and conditions of the base material.
WORKS IN ALL HOLLOW BASE MATERIALS:
DRYWALL
1
• Be sure to use a screw at least a half inch longer than the grip range you are anchoring. Grip range includes
the wall thickness plus the thickness of what you are anchoring and any space in between.
• Pre-drill a 1/2 inch hole, or if using in drywall you can penetrate the drywall with the self penetrating tip.
Push head of anchor against the strap so the pointed section of the anchor is pointing up. In 3/8” & 1/2”
drywall, you can push the self-drilling tip through the drywall by pushing and moving the tip in an up and
down motion until penetrating through the drywall.
• Insert the plastic nut into the 1/2 inch hole tight & ush. Use your thumb or ngers to hold the plastic nut
and pull the strap to pull the head of the anchor tight against the back of the wall. Break off the strap by
moving it up and down.
• Your anchor is set and ready to anchor your project. Mount xture to be hung, insert screw with hand and
tighten screw a few rotations. Finish driving the screw with a screwdriver or drill and tighten securely.
4
2
3
Easy Installation
PERFORMANCE GUIDE
Product
Size
Drill
Size
Screw Size
Grip Range
(included
screws)
Maximum
Grip Range
Safe Work
Load in 1/2"
Drywall
Safe Work Load
in 1/2" Drywall
Ceiling
Safe Work Load
in C90 Block
3/16" 1/2" 10-24 x 2-1/2 2" 3" 120 60 620
1/4" 1/2" 1/4-20 x 2-1/2 2" 3" 155 65 785
*Safe Working Loads are based on a 2:1 ultimate to safe working load ratio.
989709