Users Manual

The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12 V, 0.5 A.
Positions When Collecting/
Comparing Face Picture
(Recommended Distance: 0.5m)
Tips When Collecting/
Comparing Face Picture
Expression
Posture
Size
0.5m
Too High
Too Low
Too Close Too Far
0.5 m
Make sure your face is in the middle of the collecng window.
Correct Tilt RaiseSide Bow
0.5m 0.5m
Correct
Too Close Too Far
Recommended:
Use other authencaon methods if the device if affected by the
light or other items.
1:N Matching: The device will compare the captured face picture
with the ones in the database.
1:1 Matching: The device will compare the captured face picture
with the user linked face picture.
Keep your expression naturally when collecng or
comparing face pictures, just like the expression in the
picture on the right.
In order to get a good quality and accurate face picture, posion your
face looking at the camera when collecng or comparing face pictures.
Do not wear hat, sunglasses, or other accessories that
can affect the facial recognion funcon.
Do not make your hair cover your eyes, ears, etc. and
heavy makeup is not allowed.
Power on and wire the network cable aer installaon. You
should acvate the device before the first login.
If the device is not acvated yet, it will enter the Acvate
Device page aer powering on.
Steps:
1. Create a password and confirm the password.
2. Tap Acvate to acvate the device.
For other acvaon methods, see the device user manual.
Sensor Input
Power Input
SENSOR
BUTTON
B1
B2
B3
B4
Green/Brown
Door Contact
Black
Green/Black
Black
Lock Output
NC
C1
C2
C3
COM
(NC)
Power
(NO)
(COM)
White/Purple
White/Black
White/Red
Exit Button
Face Recognition Terminal
NO
COM
NC
NO
COM
NC
Electric
Dropbolt
Electric
Strike
Secure Door Control Unit
Red
Black
Exit Button
RS-485
B1
B2
B3
Red/Black
Yellow
Blue
Secure Door
Control Unit
Wiring Terminal
3.2
Device Wiring (With Secure Door Control Unit)
4
Activation
5
Temperature Measurement and Face Mask Settings
5
5
6
Add Face Picture
STRONG PASSWORD RECOMMENDED–
We highly recommend you create a strong password of your own
choosing (using a minimum of 8 characters, including upper case
leers, lower case leers, numbers, and special characters) in
order to increase the security of your product. And we
recommend you reset your password regularly, especially in the
high security system, reseng the password monthly or weekly
can beer protect your product.
Biometric recognion products are not 100% applicable
to an-spoofing environments. If you require a higher
security level, use mulple authencaon modes.
1. Use finger to hold the screen surface for 3 s and slide to
right/le and enter the acvaon password to enter the Home
page.
2. Enter the User Management page, tap + to enter the Add User
page.
3. Set the user parameters according to actual needs.
4. Tap Face and collect the face informaon according to the
instrucons.
You can view the captured picture on the screen. Make sure the
face picture is in good quality and size.
For details about the ps and posions when collecng or
comparing the face picture, see the contents on the right.
5. If the picture is in good condion, tap the save icon.
Or tap the try again icon to take another face picture.
6. Tap the save icon save the sengs.
Go back to the inial page to start authencaon.
For other authencaon methods, see the device user manual.
Only the devices with the fingerprint module support the
fingerprint related funcons.
Regulatory Information
This product and - if applicable - the supplied accessories too are marked with
"CE" and comply therefore with the applicable harmonized European standards
listed under the RE Direcve 2014/53/EU, the EMC Direcve 2014/30/EU, the
RoHS Direcve 2011/65/EU.
2012/19/EU (WEEE direcve): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collecon points. For
more informaon see: www.recyclethis.info
2006/66/EC (baery direcve): This product contains a baery that cannot be
disposed of as unsorted municipal waste in the European Union. See the
product documentaon for specific baery informaon. The baery is marked
with this symbol, which may include leering to indicate cadmium (Cd), lead
(Pb), or mercury (Hg). For proper recycling, return the baery to your supplier
or to a designated collecon point. For more informaon see: www.recycle-
this.info
FCC Conditions
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two
condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operaon.
EU Conformity Statement
FCC Information
Please take aenon that changes or modificaon not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protecon against harmful interference in a residenal installaon. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
Warnings
All the electronic operaon should be strictly compliance with the electrical safety
regulaons, fire prevenon regulaons and other related regulaons in your local region.
Please use the power adapter, which is provided by normal company. The power
consumpon cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the
power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service
center. Never aempt to disassemble the device yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
Cauons
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnesm radiaon. Avoid the equipment installaon on vibraons surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specificaon of the device for the
detailed operang temperature), cold, dusty or damp locaons, and do not expose it to
high electromagnec radiaon.
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low venlaon or heat source such as heater
or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfuncon however), and affecng the endurance of sensor at
the same me.
Please use the provided glove when open up the device cover, avoid direct contact with
the device cover, because the acidic sweat of the fingers may erode the surface coang of
the device cover.
Please use a so and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers aer unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportaon without the original wrapper may result in damage on the device and lead
to addional costs.
Risk of explosion if the baery is replaced by an incorrect type
Improper replacement of the baery with an incorrect type may defeat a safeguard (for
example, in the case of some lithium baery types).
This equipment is not suitable for use in locaons where children are likely to be
present.
Do not dispose of the baery into fire or a hot oven, or mechanically crush or cut the
baery, which may result in an explosion.
Do not leave the baery in an extremely high temperature surrounding environment,
which may result in an explosion or the leakage of flammable liquid or gas.
Do not subject the baery to extremely low air pressure, which may result in an
explosion or the leakage of flammable liquid or gas.
Dispose of used baeries according to the instrucons
Indoor use. When installing the device indoors, the device should be at least 2 meters
away from the light, and at least 3 meters away from the window or the door.
Safety Instruction
These instrucons are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precauon measure is divided into Warnings and Cauons:
Warnings: Neglecng any of the warnings may cause serious injury or death.
Cauons: Neglecng any of the cauons may cause injury or equipment damage.
1. Use finger to hold the screen surface for 3 s and slide to right/le. Enter the acvaon password to
enter the home page.
2. Tap “Temperature” to enter the Temperature Sengs page. Configure the parameters.
Enable Temperature Detecon:
When enabling the funcon, the device will authencate the permissions and at the same me take
the tempearture. When disabling the device, the device will authencate the permissions only.
Thermal Module IP Address:
If you edit the IP address of the thermal module on the plaorm, you should change it on the
device.
Over-Temperature Alarm Threshold:
Edit the threshold according to actual situaon. If the detected temperature is higher than the
configured one, an alarm will be triggered. By default, the value is 37.3°。
Distance for Measuring Temperature (m):
Edit the distance according to actual situaon. The distance between the person and the device
should be the same as the configured value. Suggested: 0.3 to 0.5 m. By defalt: 0.3 m。
Door Not Open When Detecng Abnormal Termperature:
When Enabling the funcon, the door will not open when the detected temperature is higher than
the configured temperature threshold. By default, the temperature is enabled.
Temperature Measurement Only:
When enabling the funcon, the device will not authencate the permissions, but only take the
temperature. When disabling the funcon, the device will authencate the permsissions and at the
same me take the temperature.
Face with Mask Detecon:
When enabling the funcon, the device will pop up a prompt and the door will not open when the
detected person is not wear a mask.
Activate Device
Two or more of the following character types are
allowed: digit, letter, and symbol.
admin
Input 8 to 16 Characters
Confirm Password
Activate