Bullet Network Camera Quick Start Guide
© 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (http://www.hikvision.com/).
SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Cautions&Warnings These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Laws and Regulations The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations. Transportation Keep the device in original or similar packaging while transporting it. Power Supply The power source should meet limited power source or PS2 requirements according to IEC 60950-1 or IEC 62368-1 standard.
Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. Maintenance If the product does not work properly, please contact your dealer or the nearest service center. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
DO NOT stare at operating light source. May be harmful to the eyes. Wear appropriate eye protection or DO NOT turn on the white light when you assemble, install or maintain the camera. Emergency If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center. Time Synchronization Set up device time manually for the first time access if the local time is not synchronized with that of the network.
CAUTION: Hot parts! Burned fingers when handling the parts. Wait one-half hour after switching off before handling parts. This sticker is to indicate that the marked item can be hot and should not be touched without taking care.
Functional grounding Disposal Purchase separately Other situations Other situations omitted Waterproof Skip this step if not necessary
Installation 1. 2. 3. 4. 5.
Installation 2
Installation * 1x 1x 1x T10 T20 1x 2x* 3 1x
Installation Interface Introduction - Type 1 Memory Card Slot Reset Button Network Interface Power Input Interface Audio Interface Alarm Interface Power Output Interface 4
Installation Interface Introduction - Type 2 Memory Card Slot Reset Button Network Interface Power Input Interface Audio Interface Alarm Interface Power Output Interface 5
Installation Interface Introduction - Type 3 Memory Card Slot Reset Button Network Interface Power Interface Audio Interface Alarm Interface 6
Installation Interface Introduction - Type 4 Memory Card Slot Reset Button Network Interface Power Interface Alarm Interface Wiegand Interface 7
Installation 1.
Installation 1.
Installation 2.1 A.1-A.4 B.1-B.
Installation A.1 A.2 Ø5.
Installation A.3 A.4 5.0 2.
Installation B.1 B.2 Ø5.
Installation B.3 B.4 5.0 2.
Installation A.4 B.4 2.
Installation 2.3 5.
Installation 2.
Installation 2.
Installation 19
Installation 2.
Installation 3.
Installation 3.
Installation 3.
Installation 4.
Operation Activate and Access Network Camera Scan the QR code to get Activate and Access Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
Operation Reset and Restore Camera Press Reset button for about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. For the position of the reset button, refer to the figures in the interface introduction page.
UD19213B-B
