User's Manual

UDB
The figures are for reference only.
Direct
Sunlight
Direct Sunlight
through Window
Backlight
Indirect Sunlight
through Window
Close to Light
Installation Environment:
Indoor installaon is supported. The device should be at least 2 meters
away from the light, and at least 3 meters away from the window or the
door.
The addional force shall be equal to three mes the weight of the equipment
but not less than 50N. The equipment and its associated mounng means shall
remain secure during the installaon. Aer the installaon, the equipment, including
any associated mounng plate, shall not be damaged.
IR
Light
Screen
Camera Camera
IR Light
Debugging
Port (For
debugging
only)
Wiring
Terminal
PSAM Card Slot
(Reserved)
TAMPER
Network
Interface
185.8 mm
103.36 mm
20.7mm
91.84±0.15 mm
10.2±0.15 mm
Card
Presenting
Area
microUSB
(Use microUSB to USB cabe
to connect with USB interface)
DS-K1T672 Series
Face Recognition Terminal
Quick Start Guide
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instrucons on how to use the Product. The soware embodied in the Product is
governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domes
c and internaonal copyright protecon. Hangzhou Hikvision
Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be
reproduced, changed, translated, or distributed, parally or wholly, by any means, without the
prior wrien permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered
trademarks or the subject of applicaons for the same by Hikvision and/or its affiliates. Other
trademarks menoned in this manual are the properes of their respecve owners. No right of
license is given to use such trademarks without express permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE,
AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS,
OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN
CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
Data Protecon
During the use of device, personal data will be collected, stored and processed. To protect data,
the development of Hikvision devices incorporates privacy by design principles. For example, for
device with facial recognion features, biometrics data is stored in your device with encrypon
method; for fingerprint device, only fingerprint template will be saved, which is impossible to
reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with
the applicable data protecon laws and regulaons, including without limitaon, conducng
security controls to safeguard personal data, such as, implemenng reasonable administrave and
physical security controls, conduct periodic reviews and assessments of the effecveness of your
security controls.
Scan the QR code to get the user manual for detailed information.
Use only power supplies listed in the user instrucons:
When connecng door magnec sensor and exit
buon, the device and the RS-485 card reader
should use the common ground connecon.
The Wiegand termimal here is a Wiegand input
terminal. You should set the face recognion
terminal’s Wiegand direcon to “Input”. If you
should connect to an access controller, you should
set the Wiegand direcon to “Output”. For details,
see Seng Wiegand Parameters in Communicaon
Sengs in the user manual.
The suggested external power supply for door lock
is 12 V, 1A.
The suggested external power supply for Wiegand
card reader is 12 V, 1 A.
For wiring the fire system, see the user manual.
Model
Manufacture
Standard
ADS-26FSG-12 12024EPG
Shenzhen Honor Electronic Co.,Ltd
PG
MSA-C2000IC12.0-24P-DE
MOSO Technology Co.,Ltd
PDE
ADS-26FSG-12 12024EPB
Shenzhen Honor Electronic Co.,Ltd
PB
ADS-26FSG-12 12024EPCU/EPC
Shenzhen Honor Electronic Co.,Ltd
PCU
ADS-26FSG-12 12024EPI-01 Shenzhen Honor Electronic Co.,Ltd PI
ADS-26FSG-12 12024EPBR
Shenzhen Honor Electronic Co.,Ltd
PBR
1
Installation
2
Appearance
3.1
Device Wiring (Normal)
Network Interface
Wiegand
Door Lock
RS-485
Alarm Output
Alarm Input
GND
Black
Green
White
Yellow
Blue
Black
White/Purple
White/Yellow
Yellow/Green
White/Red
Black
Yellow/Grey
GND
GND
Yellow/Black
GND
BTN
12V Power Supply
Wiegand
Card Reader
Group B
Group D
C1
C2
C3
C4
C5
C6
IN2
GND
IN1
Yellow/Orange
Black
Yellow/Blue
Red
Black
Yellow/Red
Yellow/Brown
Yellow/Purple
NO
COM
NC
B1
B2
B3
B4
B5
B6
D6
D7
D1
D2
D3
D4
D5
(NC)
(COM)
NO
COM
NC
NO
COM
NC
(NO)
Alarm Input Device
Alarm Output Device
Alarm Output Device
Power Supply
(NO)
(NC)
Door Contact
Electric Dropbolt
Electric Strike
Power Supply
Exit Button
Power Input
1
Make sure the gang box is installed on the wall.
3
Align the device with the mounting plate and hang the
the device on the mounting plate.
Use 1 supplied screw to secure the device on the mounting
plate.
2
Use 1 supplied screw to secure base plate on the gang box.
Use another two supplied screws to secure the mounng plate on the base plate.
Route the cables through the cable hole of the mounng plate, and connect to
the correcsponding external device’s cables.