DS-K1T643 Series Face Recognition Terminal User Manual
DS-K1T643 Series Face Recognition Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T643 Series Face Recognition Terminal User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T643 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T643 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T643 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T643 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T643 Series Face Recognition Terminal User Manual • + identifies the positive terminal(s) of equipment which is used with, or generates direct current. - identifies the negative terminal(s) of equipment which is used with, or generates direct current. • CAUTION: This bracket is intended for use only with DS-K1T341BMI-T/DS-K1T341BMWI-T face recognition terminal. Use with other equipment may result in instability causing injury. • CAUTION: This equipment is for use only with the corresponded bracket.
DS-K1T643 Series Face Recognition Terminal User Manual • Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. • The USB port of the equipment is used for connecting to a mouse, a keyboard, or a USB flash drive only.
DS-K1T643 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model DS-K1T643MX-T DS-K1T643MWX-T Use only power supplies listed in the user instructions: Model Manufacturer Standard ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd PG MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd PDE ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.,Ltd PB ADS-26FSG-12 12024EPCU/EPC Shenzhen Honor Electronic Co.
DS-K1T643 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T643 Series Face Recognition Terminal User Manual 7.1.1 Login by Administrator ................................................................................................ 26 7.1.2 Login by Activation Password ...................................................................................... 28 7.2 Communication Settings ...................................................................................................... 30 7.2.1 Set Wired Network Parameters ...................................
DS-K1T643 Series Face Recognition Terminal User Manual 7.12 Video Intercom .................................................................................................................. 56 7.12.1 Call Client Software from Device ............................................................................... 56 7.12.2 Call Center from Device ............................................................................................ 57 7.12.3 Call Device from Client Software .............................
DS-K1T643 Series Face Recognition Terminal User Manual 8.5.17 Time and Attendance Settings .................................................................................. 76 8.5.18 Set Video Intercom Parameters ................................................................................ 79 8.5.19 Configure SIP Parameters .......................................................................................... 80 8.5.20 Access Control Settings .........................................................
DS-K1T643 Series Face Recognition Terminal User Manual 9.7.1 Configure Device Parameters .................................................................................... 111 9.7.2 Configure Device Parameters .................................................................................... 118 9.8 Door/Elevator Control ........................................................................................................ 121 9.8.1 Control Door Status ..................................................
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview The face recognition terminal is a kind of access control device integrated with temperature screening function. It can fast taking skin-surface temperature and upload abnormal temperature event to the center, which can be widely applied in multiple scenarios, such as enterprises, stations, dwellings, factories, schools, campus and so on. 1.
DS-K1T643 Series Face Recognition Terminal User Manual • • • • Imports and export data to the device from the client software Supports simple theme Supports configuration via Web Supports ISUP 5.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No.
DS-K1T643 Series Face Recognition Terminal User Manual No. Name 10 Network Interface 11 Debugging Port Note The debug terminal is used for debugging only.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment • Avoid backlight, direct sunlight, and indirect sunlight. • For better face recognition, there should be light source in or near the installation environment. • Sunlight, wind, hot/cool air from air conditioner and other external factors, which may affect surface temperature, will create the deviation of the temperature measurement.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 3-1 Install Gang Box 2. Use 2 supplied screws (KA4*22) to secure the mounting plate on the gang box. Figure 3-2 Install Mounting Plate 3. Remove the 2 screws on the rear panel and remove the sheet to display the wiring terminals. 4. Route the cable through the cable hole of the mounting plate, and connect to corresponding external devices' cables. 5. Install the sheet back to the device with the two screws. 6.
DS-K1T643 Series Face Recognition Terminal User Manual Note Make sure the 2 sheets on each side of the mounting plate have been in the holes at the back of the device. 7. Use 2 supplied M3*8 screws to secure the device and the mounting plate. Figure 3-3 Secure Device 3.3 Install without Gang Box Steps Note The additional force shall be equal to three times the weight of the equipment. The equipment ad its associated mounting means shall remain secure during the installation.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 3-4 Mounting Template 2. Drill holes on the wall or other surface according to the instructions on the mounting template. 3. Align the holes to the mounting plate and secure the mounting plate on the wall with the 3 supplied screws (KA4*22).
DS-K1T643 Series Face Recognition Terminal User Manual Figure 3-5 Install Mounting Plate 4. Remove the 2 screws on the rear panel and remove the sheet to display the wiring terminals. 5. Route the cable through the cable hole of the mounting plate, and connect to corresponding external devices' cables. 6. Install the sheet back to the device with the two screws. 7. Align the device with the mounting plate and hang the device on the mounting plate. 8.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 4 Wiring The device supports connecting to the RS-485 terminal, the door lock, the exit button, the alarm output/input devices, the Wiegand card reader, the access controller, and the power supply. You can wire the peripherals according to the descriptions below.
DS-K1T643 Series Face Recognition Terminal User Manual Group No. Function Color Name Description D3 White/Red NO Lock Wiring (NO) D4 Yellow/Green SENSOR Door Contact D5 Black GND Ground D6 Yellow/Gray BUTTON Exit Door Wiring D7 Yellow/Black GND Ground 4.2 Wire Normal Device You can connect the terminal with normal peripherals.
DS-K1T643 Series Face Recognition Terminal User Manual • • • • • Note You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters . The suggested external power supply for door lock is 12 V, 1 A.
DS-K1T643 Series Face Recognition Terminal User Manual 4.4 Wire Fire Module 4.4.1 Wiring Diagram of Door Open When Powering Off Lock Type: Anode Lock, Magnetic Lock, and Electric Bolt (NO) Security Type: Door Open When Powering Off Scenario: Installed in Fire Engine Access Type 1 Note The fire system controls the power supply of the access control system.
DS-K1T643 Series Face Recognition Terminal User Manual Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed. Figure 4-6 Wiring Device Figure 4-7 Wiring Secure Door Control Unit 4.4.
DS-K1T643 Series Face Recognition Terminal User Manual Note • The Uninterpretable Power Supply (UPS) is required. • The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NC and COM are open.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: • The default IP address: 192.0.0.64 • The default port No.: 8000 • The default user name: admin 5.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 5-1 Activation Page Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T643 Series Face Recognition Terminal User Manual • After activation, you should select a language according to your actual needs. • After activation, you should select an application mode. For details, see Set Application Mode . • After activation, if you need to add the device to the client software or other platforms, you should edit the device IP address. For details, see Set Network Parameters .
DS-K1T643 Series Face Recognition Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K1T643 Series Face Recognition Terminal User Manual three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list. Figure 6-1 Welcome Page 2. Tap OK to save.
DS-K1T643 Series Face Recognition Terminal User Manual • • • • Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 6-2 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Tap Next. Wired Network Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway.
DS-K1T643 Series Face Recognition Terminal User Manual Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Tap Skip to skip network settings. 6.3 Set Administrator After device activation, you can add an administrator to manage the device parameters. Before You Start Activate the device and select an application mode. Steps 1. Optional: Tap Skip to skip adding administrator if required. 2.
DS-K1T643 Series Face Recognition Terminal User Manual 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Enter the card No. or present card on the card presenting area. Click OK. 4. Click OK. You will enter the authentication page. Status Icon Description / Device is armed/not armed. / Hik-Connect is enabled/disabled.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 7-1 Admin Login 2. Authenticate the administrator's face or card to enter the home page.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed attempts. 3. Optional: Tap 4. Optional: Tap and you can enter the device activation password for login. and you can exit the admin login page. 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login.
DS-K1T643 Series Face Recognition Terminal User Manual Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Tap the Password field and enter the device activation password. 3. Tap OK to enter the home page. Note The device will be locked for 30 minutes after 5 failed password attempts.
DS-K1T643 Series Face Recognition Terminal User Manual 7.2 Communication Settings You can set the network parameters, the Wi-Fi parameter, the RS-485 parameters, and the Wiegand parameters on the communication settings page. 7.2.1 Set Wired Network Parameters You can set the device wired network parameters, including the IP address, the subnet mask, the gateway, and DNS parameters. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2.
DS-K1T643 Series Face Recognition Terminal User Manual Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Tap Comm.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable.
DS-K1T643 Series Face Recognition Terminal User Manual 6. Tap OK to save the settings and go back to the Wi-Fi tab. 7. Tap to save the network parameters. 7.2.3 Set RS-485 Parameters The face recognition terminal can connect external access controller, secure door control unit or card reader via the RS-485 terminal. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap RS-485 to enter the RS-485 tab.
DS-K1T643 Series Face Recognition Terminal User Manual 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wiegand to enter the Wiegand tab. Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction. • Output: A face recognition terminal can connect an external access controller.
DS-K1T643 Series Face Recognition Terminal User Manual Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID. Note • The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. • The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard.
DS-K1T643 Series Face Recognition Terminal User Manual 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID. Note • The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. • The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 7-8 Add Face Picture 6. Look at the camera. Note • Make sure your face picture is in the face picture outline when adding the face picture. • Make sure the captured face picture is in good quality and is accurate. • For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page.
DS-K1T643 Series Face Recognition Terminal User Manual Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 10. Tap to save the settings. 7.3.3 Add Card Add a card for the user and the user can authenticate via the added card. Steps Note Up to 10,000 cards can be added. 1.
DS-K1T643 Series Face Recognition Terminal User Manual Note • The card No. cannot be empty. • Up to 20 characters are allowed in the card No. • The card No. cannot be duplicated. 8. Configure the card type. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user.
DS-K1T643 Series Face Recognition Terminal User Manual Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 7. Tap to save the settings. 7.3.
DS-K1T643 Series Face Recognition Terminal User Manual Note The employee ID cannot be edited. 7.4 Temperature Measurement Settings You can set the temperature measurement parameters, including temperature detection, overtemperature alarm threshold, temperature compensation, door not open when temperature is abnormal, temperature measurement mode, temperature unit, etc. On the Home page, tap Temperature to enter the Temperature page.
DS-K1T643 Series Face Recognition Terminal User Manual Table 7-1 Temperature Measurement Parameters Descriptions Parameter Description Temp. Detection When enabling the function, the device will authenticate the permissions and at the same time take the temperature. When disabling the device, the device will authenticate the permissions only. Norm Temp. (Max./Min.) Edit the threshold according to actual situation.
DS-K1T643 Series Face Recognition Terminal User Manual Authenticate face, fingerprint, card or QR code. Face Face forward at the camera and start authentication via face. Fingerprint Place the enrolled fingerprint on the fingerprint module and start authentication via fingerprint. Card Present the card on the card presenting area and start authentication via card. Note The card can be normal IC card, or encrypted card. QR Code Put the QR code in front of the device camera to authenticate via QR code.
DS-K1T643 Series Face Recognition Terminal User Manual Note • For detailed information about scanning fingerprint, see Tips for Scanning Fingerprint. • For detailed information about authenticating face, see Tips When Collecting/Comparing Face Picture. If authentication succeeded, the prompt "Authenticated" will pop up. 7.7 Basic Settings You can set the shortcut key, voice, time, language, supplement light, community No., building No., Unit No., beauty, and advertisement.
DS-K1T643 Series Face Recognition Terminal User Manual Shortcut Key Choose the shortcut key that displayed on the authentication page, including the call function, call type, and the password entering function. Note • You can select call type from Call Room, Call Center, and Call Specified Room No. Call Room When you tap the call button on the authentication page, you should dial a room No. to call. Call Center When you tap the call button on the authentication page, you can call the center directly.
DS-K1T643 Series Face Recognition Terminal User Manual 7.8 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance. The configurable parameters includes application mode, face liveness level, face recognition distance, face recognition interval, wide dynamic, face 1:N security level, face 1:1 security level, ECO settings, and face with mask detection. Long tap on the initial page for 3 s and login the home page. Tap Biometric.
DS-K1T643 Series Face Recognition Terminal User Manual Parameter Description ECO Mode (1:1) Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 7-12 Access Control Parameters The available parameters descriptions are as follows: Table 7-3 Access Control Parameters Descriptions Parameter Description Terminal Auth. Mode (Terminal Select the face recognition terminal's authentication mode. You Authentication Mode) can also customize the authentication mode. Note • Biometric recognition products are not 100% applicable to anti-spoofing environments.
DS-K1T643 Series Face Recognition Terminal User Manual Parameter Description Door Contact You can select "Open (Remain Open)" or "Close (Remian Closed)" according to your actual needs. By default, it is Close (Remian Closed). Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Available door locked time range: 1 to 255s. Authentication Interval Set the device authenticating interval. Available authentication interval range: 0 to 65535.
DS-K1T643 Series Face Recognition Terminal User Manual 7.10.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Manual. Figure 7-14 Manual Attendance Mode 3. Enable the Attendance Status Required. 4.
DS-K1T643 Series Face Recognition Terminal User Manual Note If you do not select a status, the authentication will be failed and it will not be marked as a valid attendance. 7.10.3 Set Auto Attendance via Device Set the attendance mode as auto, and you can set the attendance status and its available schedule. The system will automatically change the attendance status according to the configured schedule. Before You Start Add at least one user, and set the user's authentication mode.
DS-K1T643 Series Face Recognition Terminal User Manual The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 3) Set the selected attendance status's start time of the day. 4) Tap Confirm. 5) Repeat step 1 to 4 according to your actual needs. Note The attendance status will be valid within the configured schedule.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 7-16 Manual and Auto Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday.
DS-K1T643 Series Face Recognition Terminal User Manual select a status to take attendance manually, the authentication will be marked as the edited attendance status. Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.11 System Maintenance You can view the system information and the capacity.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 7-17 Maintenance Page System Information You can view the device model, serial No., versions, address, production data, QR code, and open source code license. Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of, user, face picture, card, and event. Device Upgrade Plug the USB flash drive in the device USB interface.
DS-K1T643 Series Face Recognition Terminal User Manual Unlink APP Account After unlinking APP account, you cannot operate via APP. Restore to Default Settings All parameters, except for the communication settings, remotely imported user information, will be restored to the default settings. The system will reboot to take effect. Restore to Factory Settings All parameters will be restored to the factory settings. The system will reboot to take effect. Reboot Reboot the device. 7.
DS-K1T643 Series Face Recognition Terminal User Manual 7.12.2 Call Center from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the main station and the device to the client software. Note For details about adding device, see Add Device. 5.
DS-K1T643 Series Face Recognition Terminal User Manual 7.12.4 Call Room from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the indoor station and the device to the client software. Note For details about adding device, see Add Device. 5.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 8 Operation via Web Browser 8.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:".
DS-K1T643 Series Face Recognition Terminal User Manual Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream.
DS-K1T643 Series Face Recognition Terminal User Manual Add Face Picture Click User → Add to enter the Add Person page. Click + on the right to upload a face picture from the local PC. Note The picture format should be JPG, JPEG or PNG. The size should be less than 200K. Click OK to save the settings. Set Permission Time Click User → Add to enter the Add Person page. Set Start Time and End Time. Click OK to save the settings. Set Access Control Click User → Add to enter the Add Person page.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 8-2 Search Page Enter the search conditions, including the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 8.5 Configuration 8.5.1 Set Local Parameters Set the live view parameters, record file saving path, and captured pictures saving path. Set Live View Parameters Click Configuration → Local to enter the Local page.
DS-K1T643 Series Face Recognition Terminal User Manual You can also click Open to open the file folder to view details. Set Captured Pictures Saving Path Click Configuration → Local to enter the Local page. Select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details. 8.5.2 View Device Information View the device name, language, model, serial No., version, number of channels, alarm input, alarm output, lock and RS-485, device capacity, etc.
DS-K1T643 Series Face Recognition Terminal User Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 8.5.4 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 8-4 DST Page 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 8.5.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 8-5 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Default The device will restore to the default settings, except for the device IP address and the user information. Restore All All parameters will be restored to the factory settings. You should activate the device before usage.
DS-K1T643 Series Face Recognition Terminal User Manual Note Do not power off during the upgrading. 8.5.7 Log Query You can search and view the device logs. Go to Configuration → System → Maintenance → Log Query . Set the major and minor type of the log type. Set the start time and end time for searching, and click Search. The results will be displayed below, which including the No., time, the major type the minor type, the channel No., the local/remote user information, the remote host IP, etc. 8.5.
DS-K1T643 Series Face Recognition Terminal User Manual Note The function is only supported by certain device models. Create and Install Self-signed Certificate Steps 1. Go to Configuration → System → Security → Certificate Management . 2. In the Certificate Files area, select a Certificate Type from the drop-down list. 3. Click Create. 4. Input certificate information. 5. Click OK to save and install the certificate. The created certificate is displayed in the Certificate Details area.
DS-K1T643 Series Face Recognition Terminal User Manual Note The input certificate ID cannot be the same as the existing ones. 3. Upload a certificate file from the local. 4. Click Install. 8.5.10 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3. Enter the old password and create a new password. 4. Confirm the new password. 5. Click OK. Caution The password strength of the device can be automatically checked.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 8-6 TCP/IP Settings Page Set the parameters and click Save to save the settings. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, MTU, and the device port. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, and the IPv4 default gateway automatically. NIC Type Select a NIC type from the drop-down list. By default, it is Auto.
DS-K1T643 Series Face Recognition Terminal User Manual Set the HTTPS for accessing the browser. Certificate is required when accessing. Server It refers to the port through which the client adds the device. Set Wi-Fi Parameters Set the Wi-Fi parameters for device wireless connection. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Basic Settings → Wi-Fi . Figure 8-7 Wi-Fi Settings Page 2. Check Wi-Fi. 3.
DS-K1T643 Series Face Recognition Terminal User Manual You can set the center group and the system will transfer logs via ISUP protocol. Click Save to save the settings. Center Group Select a center group from the drop-down list. Main Channel The device will communicate with the center via the main channel. Note N1 refers to wired network. Platform Access Platform access provides you an option to manage the devices via platform. Steps 1.
DS-K1T643 Series Face Recognition Terminal User Manual Note If you select 5.0 as the version, you should set the ISUP key as well. 5. Click Save. Configure HTTP Listening The device can send alarm information to the destination IP or host via HTTP protocol/HTTPS protocol. Before You Start The destination IP or host name should support the HTTP protocol/HTTPS protocol to receive the alarm information. Note The function should be supported by the device. Steps 1.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 8-8 Video Settings Page Set the stream type, the video type, the bitrate type, the frame rate, the Max. bitrate, and the video encoding. Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio . Set the audio stream type and audio encoding. Drag the slider to adjust the device input and output volume. You can also enable voice prompt.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 8-9 Customize Audio Content 2. set the appellation. 3. Enable the function. 4. Set the time duration when authentication succeeded. 1) Click Add. 2) Set the time duration and the language. Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. 5.
DS-K1T643 Series Face Recognition Terminal User Manual 8.5.15 Set Image Parameters Set the video standard, WDR, brightness, contrast, saturation, and sharpness. Steps 1. Click Configuration → Image Adjustment . Figure 8-10 Image Settings Page 2. Configure the parameters to adjust the image. Video Standard Set the video frame rate when performing live view remotely. After changing the standard, you should reboot the device to take effect. PAL 25 frames per second.
DS-K1T643 Series Face Recognition Terminal User Manual Capture the image. 3. Click Default to restore the parameters to the default settings. 8.5.16 Set Supplement Light Brightness Set the device supplement light brightness. Steps 1. Click Configuration → Image → Supplement Light Parameters . Figure 8-11 Supplement Light Settings Page 2. Select a supplement light type and mode from the drop-down list. If you select the mode as ON, you should set the brightness. 8.5.
DS-K1T643 Series Face Recognition Terminal User Manual Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Disable. Result You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. Time Settings Steps 1. Click Configuration → Time Settings to enter the settings page. 2. Select Status Type. 3. Optional: Edit Schedule Name according to the actual needs. 4.
DS-K1T643 Series Face Recognition Terminal User Manual Note If you do not select a status, the authentication will be failed and it will not be marked as a valid attendance. Set Auto Attendance via Web Set the attendance mode as auto, and you can set the attendance status and its available schedule. The system will automatically change the attendance status according to the configured schedule. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management.
DS-K1T643 Series Face Recognition Terminal User Manual Result On the initial page and authenticate. The authentication will be marked as the configured attendance status according to the schedule. If you tap the edit icon on the result tab, you can select a status to take attendance manually, the authentication will be marked as the edited attendance status.
DS-K1T643 Series Face Recognition Terminal User Manual Period No. Set the device installed period No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. Community No. Set the device installed community No. If set the device type as Outer Door Station, you can set the period No., outer door station No.
DS-K1T643 Series Face Recognition Terminal User Manual Go to Configuration → Access Control → Linked Network Settings . Set the main station's IP address and SIP server's IP address. Click Save. 8.5.20 Access Control Settings Set Authentication Parameters Click Configuration → Access Control → Authentication Settings . Note The functions vary according to different models. Refers to the actual device for details.
DS-K1T643 Series Face Recognition Terminal User Manual Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list. Display Authentication Result Check Face Picture, Name, or Employee ID. When authentication is completed, the system will display the selected contents in the result. Minimum Recognition Interval You can set the interval between 2 continuous recognition of a same person during the authentication.
DS-K1T643 Series Face Recognition Terminal User Manual When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Max. Interval When Entering Password When you entering the password on the card reader, if the interval between pressing two digits is longer than the set value, the digits you pressed before will be cleared automatically.
DS-K1T643 Series Face Recognition Terminal User Manual Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed. Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Open.
DS-K1T643 Series Face Recognition Terminal User Manual M1 card encryption can improve the security level of authentication. Enable the function and set the encryption sector. By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. Enable EM Card Enable EM card and authenticating by presenting EM card is available. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function.
DS-K1T643 Series Face Recognition Terminal User Manual Steps Note Some device models do not support this function. Refer to the actual products when configuration. 1. Click Configuration → Access Control → Wiegand Settings . Figure 8-15 Wiegand Page 2. Check Wiegand to enable the Wiegand function. 3. Set a transmission direction. Input The device can connect a Wiegand card reader. Output The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. 4.
DS-K1T643 Series Face Recognition Terminal User Manual Set Privacy Parameters Set the event storage type, picture upload and storage parameters, and the picture clearing parameters. Go to Configuration → Access Control → Privacy Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting. Delete Old Events Periodically Drag the block or enter number to set the period for event deleting.
DS-K1T643 Series Face Recognition Terminal User Manual If you enable this function, you can save the thermographic picture captured to the device. Clear All Pictures in Device Note All pictures cannot be restored once they are deleted. Clear Registered Face Pictures All registered pictures in the device will be deleted. Clear Captured Pictures All captured pictures in the device will be deleted. Set Card Authentication Parameters Set the card reading content when authenticate via card on the device.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 8-16 Smart Settings Page Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K1T643 Series Face Recognition Terminal User Manual Face Recognition Mode Normal Mode Recognize face via the camera normally. Deep Mode The device can recognize a much wider people range than the normal mode. This mode is applicable to a more complicated environment. Continuous Face Recognition Interval Set the time interval between two continuous face recognitions when authenticating. Pitch Angle The maximum pitch angle when starting face authentication.
DS-K1T643 Series Face Recognition Terminal User Manual After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask1:N matching threshold, it's ECO mode, and the strategy. None The device will detect the face with mask without prompt. Prompt and Open If the person do not wear a face mask when authenticating, the device prompts a notification and the door will open.
DS-K1T643 Series Face Recognition Terminal User Manual 8.5.23 Temperature Measurement Settings Temperature Measurement Settings You can set the temperature measurement parameters, including temperature measurement only, temperature unit, over-temperature threshold, temperature compensation, door not open when temperature is abnormal, etc. Steps 1. Click Configuration → Temperature → Temperature Settings . Figure 8-18 Temperature Measurement Settings 2. Enable Temperature Measurement. 3.
DS-K1T643 Series Face Recognition Terminal User Manual Parameter Description Note After enabling Temperature Measurement Only, you can enable Capture White Light Picture. After enabling Capture White Light Picture, the picture will be captured when authenticating. Unit Select a temperature unit according to your preference. Over-Temperature Threshold (Max./Min.) Edit the threshold according to actual situation.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 8-19 Black Body Settings 2. Enable black body correction function. 3. Put a black body in front of the camera. Make sure there are no other objects between the camera and the black body. 4. Set the distance between the black body and the camera (straight line), the emissivity of the black body, and the temperature unit. Note The black body's temperature is fixed. 5. Click Calibrate, and draw the black body's position on the page.
DS-K1T643 Series Face Recognition Terminal User Manual Chapter 9 Client Software Configuration 9.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 9-1 Flow Diagram of Configuration on Client Software 9.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T643 Series Face Recognition Terminal User Manual 9.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. Add Device by IP Address or Domain Name If you know the IP address or domain name of the device to add, you can add devices to the client by specifying the IP address (or domain name), user name, password, etc. Steps 1.
DS-K1T643 Series Face Recognition Terminal User Manual 5. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS (Transport Layer Security) protocol for security purpose. Note • This function should be supported by the device. • If you have enabled Certificate Verification, you should click Open Certificate Directory to open the default folder, and copy the certificate file exported from the device to this default directory to strengthen the security.
DS-K1T643 Series Face Recognition Terminal User Manual Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T643 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T643 Series Face Recognition Terminal User Manual 9.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T643 Series Face Recognition Terminal User Manual Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 9.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 9.4.
DS-K1T643 Series Face Recognition Terminal User Manual 9.4.2 Import and Export Person Identify Information You can import the information and pictures of multiple persons to the client software in a batch. Meanwhile, you can also export the person information and pictures and save them in your PC. Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2.
DS-K1T643 Series Face Recognition Terminal User Manual 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel and check Face. 4. Optional: Enable Verify by Device to check whether face recognition device managed in the client can recognize the face in the photo. 5. Click to select a face picture file. Note • The (folder of) face pictures should be in ZIP format.
DS-K1T643 Series Face Recognition Terminal User Manual Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4. Click Export to start exporting. Note • The exported file is in ZIP format. • The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 9.4.
DS-K1T643 Series Face Recognition Terminal User Manual 9.4.4 Issue Cards to Persons in Batch The client provides a convenient way to issue cards to multiple persons in a batch. Steps 1. Enter Person module. 2. Click Batch Issue Cards. All the added persons with no card issued will be displayed in the right panel. 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters.
DS-K1T643 Series Face Recognition Terminal User Manual 9.4.6 Set Card Issuing Parameters The client provides two modes for reading a card's number: via card enrollment station or via the card reader of the access control device. If a card enrollment station is available, connect it to the PC running the client by USB interface or COM, and place the card on the card enrollment to read the card number.
DS-K1T643 Series Face Recognition Terminal User Manual 9.5 Configure Schedule and Template You can configure the template including holiday and week schedule. After setting the template, you can adopt the configured template to access groups when setting the access groups, so that the access group will take effect in the time durations of the template. Note For access group settings, refer to Set Access Group to Assign Access Authorization to Persons . 9.5.
DS-K1T643 Series Face Recognition Terminal User Manual 6) Optional: Click holiday list. 6. Click Save. in the Operation column to delete this added holiday period from the 9.5.2 Add Template Template includes week schedule and holiday. You can set week schedule and assign the time duration of access authorization for different person or group. You can also select the added holiday(s) for the template. Steps Note You can add up to 255 templates in the software system. 1.
DS-K1T643 Series Face Recognition Terminal User Manual Note Up to 4 holidays can be added to one template. 1) Click Holiday tab. 2) Select a holiday in the left list and it will be added to the selected list on the right panel. 3) Optional: Click Add to add a new holiday. Note For details about adding a holiday, refer to Add Holiday . 4) Optional: Select a selected holiday in the right list and click to remove the selected one, or click Clear to clear all the selected holiday(s) in the right list. 7.
DS-K1T643 Series Face Recognition Terminal User Manual Figure 9-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T643 Series Face Recognition Terminal User Manual You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 9-4 Data Synchronization 9.7 Configure Advanced Functions You can configure the advanced functions of access control to meet some special requirements in different scene. Note • For the card related functions(the type of access control card), only the card(s) with access group applied will be listed when adding cards.
DS-K1T643 Series Face Recognition Terminal User Manual Note If you can not find Device Parameter in the Advanced Function list, hover the cursor on the Advanced Function, and then Click to select the Device Parameter to be displayed. 2. Select an access device to show its parameters on the right page. 3. Turn the switch to ON to enable the corresponding functions. Note • The displayed parameters may vary for different access control devices.
DS-K1T643 Series Face Recognition Terminal User Manual NFC Anti-Cloning If you enable this function, you cannot use the cloned card for authentication and further enhance security. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s). Configure Parameters for Door/Elevator After adding the access control device, you can configure its access point (door or floor) parameters.
DS-K1T643 Series Face Recognition Terminal User Manual The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Lock Door when Door Closed The door can be locked once it is closed even if the Door Locked Time is not reached. Duress Code The door can open by inputting the duress code when there is duress. At the same time, the client can report the duress event.
DS-K1T643 Series Face Recognition Terminal User Manual Note • The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. • Some of the following parameters are not listed in the Basic Information page, click More to edit the parameters. Name Edit the card reader name as desired.
DS-K1T643 Series Face Recognition Terminal User Manual View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance. If the score is less than the configured value, face recognition will be failed. Face Recognition Timeout Value If the recognition time is more than the configured time, the device will remind you.
DS-K1T643 Series Face Recognition Terminal User Manual 4. Click OK. 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s). Configure Parameters for Alarm Output After adding the access control device, if the device links to alarm outputs, you can configure the parameters. Before You Start Add access control device to the client, and make sure the device supports alarm output. Steps 1.
DS-K1T643 Series Face Recognition Terminal User Manual • If you select According to Lane Controller's DIP Settings, the device will follow the lane controller's DIP settings to control the barrier. The settings on the software will be invalid. • If you select According to Main Controller's Settings, the device will follow the settings of the software to control the barrier. The DIP settings of the lane controller will be invalid.
DS-K1T643 Series Face Recognition Terminal User Manual Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface. Face Picture Database select Deep Learning as the face picture database. Authenticate by QR Code If enabled, the device camera can scan the QR code to authenticate. By default, the function is disabled.
DS-K1T643 Series Face Recognition Terminal User Manual Note When the connection mode is Connect Access Control Device, you can select Card No. or Person ID as the output type. 6. Click Save. • The configured parameters will be applied to the device automatically. • When you change the working mode or connection mode, the device will reboot automatically. Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode.
DS-K1T643 Series Face Recognition Terminal User Manual 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click M1 Card Encryption to enter the M1 Card Encryption page. 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. The sector ID ranges from 1 to 100. 6. Click Save to save the settings. 9.
DS-K1T643 Series Face Recognition Terminal User Manual Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T643 Series Face Recognition Terminal User Manual Before You Start You have added person(s) and access control device(s) to the client. For details, refer to Person Management and Add Device . Steps 1. Click Monitoring to enter monitoring module. Real-time access records are displayed on the bottom of the page. You can view record details, including card No., person name, event time, door location, temperature, authentication type etc.
DS-K1T643 Series Face Recognition Terminal User Manual Note In the pop-up window, you can click to view surveillance details in full screen.
DS-K1T643 Series Face Recognition Terminal User Manual Appendix A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. • Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. • Do not make your hair cover your eyes, ears, etc.
DS-K1T643 Series Face Recognition Terminal User Manual Appendix B. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2.
DS-K1T643 Series Face Recognition Terminal User Manual Appendix C.
DS-K1T643 Series Face Recognition Terminal User Manual Appendix D. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure D-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD23342B
