User's Manual
Table Of Contents
- Chapter 1 Introduction
- 1.1 Front Panel
- 1.1.1 iDS-9600NXI-I8/8F(B), iDS-9600NXI-I8/X(B) and iDS-9600NXI-I8/16S(B) Series
- 1.1.2 iDS-9600NXI-I16/8F(B), iDS-9600NXI-I16/X(B) and iDS-9600NXI-I16/16S(B) Series
- 1.1.3 iDS-7700NXI-I4(/16P)/16S(B) and iDS-7700NXI-I4(/16P)/X(B) Series
- 1.1.4 iDS-6700NXI-I/8F(B) and iDS-6700NXI-I/16S(B) Series
- 1.1.5 iDS-9600NXI-I8/4F(B)
- 1.1.6 iDS-96000NXI-I16(B)
- 1.1.7 iDS-96000NXI-I24(B)
- 1.2 IR Remote Control Operations
- 1.3 USB Mouse Operation
- 1.4 Rear Panel
- 1.4.1 iDS-9600NXI-I8/8F(B), iDS-9600NXI-I8/X(B) and iDS-9600NXI-I8/16S(B) Series
- 1.4.2 iDS-9600NXI-I16/8F(B), iDS-9600NXI-I16/X(B) and iDS-9600NXI-I16/16S(B) Series
- 1.4.3 iDS-7700NXI-I4(/16P)/16S(B) and iDS-7700NXI-I4(/16P)/X(B) Series
- 1.4.4 iDS-6700NXI-I/16S(B) and iDS-6700NXI-I/8F(B) Series
- 1.4.5 iDS-9600NXI-I8/4F(B)
- 1.4.6 iDS-96000NXI-I16(B) and iDS-96000NXI-I24(B)
- 1.1 Front Panel
- Chapter 2 Getting Started
- Chapter 3 Camera Management
- Chapter 4 Camera Settings
- Chapter 5 Live View
- Chapter 6 PTZ Control
- Chapter 7 Storage
- 7.1 Storage Device Management
- 7.2 Storage Mode
- 7.3 Recording Parameters
- 7.4 Configure Recording Schedule
- 7.5 Configure Continuous Recording
- 7.6 Configure Motion Detection Triggered Recording
- 7.7 Configure Event Triggered Recording
- 7.8 Configure Alarm Triggered Recording
- 7.9 Configure Picture Capture
- 7.10 Configure Holiday Recording
- 7.11 Configure Redundant Recording
- Chapter 8 Disk Array
- Chapter 9 File Management
- Chapter 10 Playback
- Chapter 11 Event and Alarm Settings
- Chapter 12 VCA Event Alarm
- 12.1 Facial Detection
- 12.2 Vehicle Detection
- 12.3 Line Crossing Detection
- 12.4 Intrusion Detection
- 12.5 Region Entrance Detection
- 12.6 Region Exiting Detection
- 12.7 Unattended Baggage Detection
- 12.8 Object Removal Detection
- 12.9 Audio Exception Detection
- 12.10 Sudden Scene Change Detection
- 12.11 Defocus Detection
- 12.12 PIR Alarm
- 12.13 Thermal Camera Detection
- Chapter 13 Smart Analysis
- Chapter 14 Human Body Detection
- Chapter 15 Face Picture Comparison
- Chapter 16 People Frequency Alarm
- Chapter 17 Network Settings
- Chapter 18 Hot Spare Device Backup
- Chapter 19 System Maintenance
- Chapter 20 General System Settings
- Chapter 21 Appendix
Network Video Recorder User Manual
26
Panel Description
1)
2)
3)
IR Remote Control Operations
The device may also be controlled with the included IR remote control, shown in Figure 1-8.
Batteries (2×AAA) must be installed before operation.
The IR remote is set at the factory to control the device (using default Device ID# 255) without any
additional steps. Device ID# 255 is the default universal device identification number shared by the
devices. You may also pair an IR Remote to a specific device by changing the Device ID#, as follows:
No.
Name
Function Description
1
Front Panel
Lock
Locks or unlocks the panel by the key.
2
Power Button
Turn on/off device.
Solid blue: Device is on.
Solid red: Device is off.
3
LCD
7-inch LCD for live-view image and menu operation.
4
HDD Sequence
Indicator
Shows the HDD sequence.
5
Power
Indicator
Flashing blue: Network transmission is normal.
HDD Indicator
Solid red: At least one HDD is installed.
Unlit: No HDD is detected.
Flashing red: HDD is reading/writing.
Tx/Rx Indicator
Flashing blue: Network transmission is normal.
Ready Indicator
Solid blue: Device in running normally.
Alarm Indicator
Solid red: Relay alarm occurs.
6
USB Interface
USB interface for additional devices such as USB mouse and
USB Hard Disk Drive (HDD).