ATM Digital Video Recorder User Manual UD08845B
ATM Digital Video Recorder User Manual User Manual COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
ATM Digital Video Recorder User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
ATM Digital Video Recorder User Manual Applicable Models This manual is applicable to the models listed in the following table. Series Model DS-8104AHQI-E4 ATM DVR DS-8104AHQLI-E4 iDS-8104AHQXLI-E4 Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text.
ATM Digital Video Recorder User Manual Safety Instructions Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
ATM Digital Video Recorder User Manual Product Key Features General Connectable to HDTVI, IP and analog cameras. Up to 8 IP cameras can be added. Connectable to third-party IP cameras that adopt ONVIF or custom protocol. PAL/NTSC adaptive video inputs. H.264 video compression with high reliability and superior definition. H.264+ compression improves encoding efficiency by up to 50% and reduces data storage costs. Supports dual-stream compression.
ATM Digital Video Recorder User Manual Local Monitoring 7-inch LCD display at 1024 × 600 resolution (available for DS-8104AHQLI-E4 and iDS-8104AHQXLI-E4 series) HDMI, VGA, CVBS and LCD display outputs. Simultaneous output of VGA and HDMI with up to 1080p resolution of VGA output and up to 4K (3840 × 2160) resolution of HDMI output. 1/4/6/8/9-division live view is supported, and the display sequence of screens is adjustable. Live view screen can be switched in group.
ATM Digital Video Recorder User Manual Searching and playing back record files by events (alarm input/motion detection/smart ATM alarm). Customization of tags, searching and playing back by tags. Locking and unlocking record files. Local redundant recording and capture. Searching and playing back record files and captured files by camera No., record / picture type, start time, end time, etc. Zooming in when playback. Reverse playback for multi-channel.
ATM Digital Video Recorder User Manual Clear-text password available. GUID file can be exported for password resetting. Multiple connected analog cameras supporting HDTVI signal can be upgraded simultaneously via DVR. Network Functions 2 self-adaptive 10M/100M/1000M network interfaces, and three working modes are configurable: multi-address, load balance and network fault tolerance. IPv6 is supported.
ATM Digital Video Recorder User Manual SDK for Windows and Linux system; Source code of application software for demo; Development support and training for application system.
ATM Digital Video Recorder User Manual Table of Contents Product Key Features ........................................................................................................... 5 Chapter 1 Introduction .............................................................................................................. 16 1.1 Front Panel .................................................................................................................. 16 1.2 IR Remote Control Operations....................
ATM Digital Video Recorder User Manual 3.3 Channel-Zero Encoding ................................................................................................ 53 3.4 Adjusting Live View Settings ........................................................................................ 54 3.5 Manual Video Quality Diagnostics ............................................................................... 55 Chapter 4 PTZ Controls ...............................................................................
ATM Digital Video Recorder User Manual 6.1.5 Playing Back by Tag ........................................................................................... 102 6.1.6 Playing Back by System Logs .............................................................................. 105 6.1.7 Playing Back by Sub-Periods .............................................................................. 106 6.1.8 Playing Back External File ..................................................................................
ATM Digital Video Recorder User Manual 10.2.3 Configuring NTP Server ................................................................................... 151 10.2.4 Configuring NAT .............................................................................................. 152 10.2.5 Configuring More Settings ............................................................................... 154 10.2.6 Configuring HTTPS Port ...................................................................................
ATM Digital Video Recorder User Manual 13.3 Managing HDD Group .............................................................................................. 188 13.3.1 Setting HDD Groups ........................................................................................ 188 13.3.2 Setting HDD Property ...................................................................................... 189 13.4 Configuring Quota Mode ....................................................................................
ATM Digital Video Recorder User Manual 17.1 Glossary ................................................................................................................... 217 17.2 Troubleshooting ....................................................................................................... 218 17.3 Summary of Chnages ............................................................................................... 221 17.3.1 Version 3.4.83 ................................................................
ATM Digital Video Recorder User Manual Chapter 1 Introduction 1.1 Front Panel Refer to Figure 1-1 for the front panel of DS-8104AHQLI-E4 and iDS-8104AHQXLI-E4. Figure 1-1 Front Panel There is no LCD screen for DS-8104AHQI-E4 series ATM DVR. Table 1-1 Description of Front Panel No. Name Function Description The DIRECTION buttons are used to navigate between different fields and items in menus. 1 DIRECTION In the Playback mode, the Up and Down button is used to speed up and slow down recorded video.
ATM Digital Video Recorder User Manual The button is used to confirm selection in any of the menu modes. It can also be used to tick checkbox fields. ENTER In Playback mode, it can be used to play or pause the video. In single-frame Playback mode, pressing the button will advance the video by a single frame. In Auto-switch mode, it can be used to stop /start auto switch. Access the main menu interface. 2 MENU Switch the channels in PTZ control. Select/deselect the HDD in HDD management interface.
ATM Digital Video Recorder User Manual Figure 1-2 Remote Control The keys on the remote control closely resemble the ones found on the front panel. Refer to Table 1-2, they include: Table 1-2 Description of the IR Remote Control Buttons No. Name Description 1 POWER Power on/off the device. 2 DEV Enable/Disable Remote Control. 3 Alphanumeric Buttons: Switch to the corresponding channel in Live view or PTZ Control mode. Input numbers and characters in Edit mode. Switch channels in Playback mode.
ATM Digital Video Recorder User Manual Enter/exit the folder of USB device and HDD. Adjust focus in the PTZ Control menu. 5 A Button It is also used to switch input methods (upper and lowercase alphabet, symbols and numeric input). Enter the Manual Record setting menu. 6 REC Button In PTZ control settings, press the button and then you can call a PTZ preset by pressing Numeric button. It is also used to turn audio on/off in the Playback mode.
ATM Digital Video Recorder User Manual LEFT button is used to jump 30s backward; the RIGHT button is used to jump 30s forward. In PTZ control mode, the DIRECTION buttons are used to control the movement of PTZ camera. The ENTER button is used to confirm the selection in menu mode. The ENTER button is used to check the checkbox or switch the ON/OFF. The ENTER button is used to play/pause the video in Playback mode or advance the video by a single frame in single-frame Playback mode.
ATM Digital Video Recorder User Manual Step 2 Check and remember the DVR No. The default DVR No. is 255. This number valid for all IR remote controls. Step 3 Press the DEV button on the remote control. Step 4 Enter the DVR No. in step 2. Step 5 Press the ENTER button on the remote. If the Status indicator on the front panel turns blue, the remote control is operating properly.
ATM Digital Video Recorder User Manual Right-Click Single-Click Scrolling up Live view: Show menu. Menu: Exit current menu to upper level menu. Live view: Previous screen. Menu: Previous item. Scroll-Wheel Scrolling down Live view: Next screen. Menu: Next item. 1.
ATM Digital Video Recorder User Manual Figure 1-4 Rear Panel Table 1-5 Description of Rear Panel No. Item Description 1 VIDEO IN BNC connector for analog video input. 2 AUDIO IN BNC connector for audio input. 3 LINE IN BNC connector for two-way audio. 4 AUDIO OUT BNC connector for audio output. 5 HDMI HDMI video output connector. 6 VGA DB15 connector for VGA output. Display local video output and menu. 7 RS-232 Interface Connector for RS-232 devices.
ATM Digital Video Recorder User Manual 15 Power Switch Switch for turning on/off the device. 16 Power Supply 100 to 240 VAC power supply.
ATM Digital Video Recorder User Manual Chapter 2 Getting Started 2.1 Starting Up and Shutting Down the DVR Purpose Proper startup and shutdown procedures are crucial to expanding the life of the DVR. Before you start Check that the voltage of the extra power supply is the same with the DVR’s requirement, and the ground connection is working properly. Starting up the DVR Step 1 Check the power supply is plugged into an electrical outlet.
ATM Digital Video Recorder User Manual Figure 2-2 Shutdown Tips Rebooting the DVR While in the Shutdown menu (Figure 2-1), you can also reboot the DVR. Step 1 Enter the Shutdown menu by clicking Menu > Shutdown. Step 2 Click the Logout button to log out or the Reboot button to reboot the DVR. 2.2 Activating the Device Purpose For the first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation.
ATM Digital Video Recorder User Manual Step 2 Click OK to save the password and activate the device. Clear-text password is supported. Click the icon and you can see the clear text of the password. Click the icon again and the content of the password restores invisible. For the old version device, if you update it to the new version, the following dialog box will pop up once the device starts up. You can click YES and follow the wizard to set a strong password.
ATM Digital Video Recorder User Manual Step 5 After exporting GUID, the Attention box pops up as below. Click Yes to duplicate the password or No to cancel it. Figure 2-7 Duplicate the Password 2.3 Using the Unlock Pattern for Login Purpose For the admin, you can configure the unlock pattern for device login. 2.3.1 Configuring the Unlock Pattern After the device is activated, you can enter the following interface to configure the device unlock pattern.
ATM Digital Video Recorder User Manual Figure 2-9 Draw the Pattern Connect at least 4 dots to draw the pattern. Each dot can be connected for once only. Step 2 Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully. Figure 2-10 Confirm the Pattern If the two patterns are different, you must set the pattern again.
ATM Digital Video Recorder User Manual Figure 2-11 Reset the Pattern 2.3.2 Logging in via Unlock Pattern Only the admin user has the permission to unlock the device. Please configure the pattern first before unlocking. Please refer to Chapter 2.3.1 Configuring the Unlock Pattern. Step 1 Right click the mouse on the screen and select the menu to enter the interface. Figure 2-12 Draw the Unlock Pattern Step 2 Draw the pre-defined pattern to unlock to enter the menu operation.
ATM Digital Video Recorder User Manual Figure 2-13 Normal Login Dialog Box Figure 2-14 Lock the Account 2.4 Basic Configuration in Startup Wizard 2.4.1 Configuring the Signal Input Wizard Purpose You can configure the analog and IP signal input types and the connectable maximum IP camera number. You can also click Menu > Camera > Signal Input Status to configure the signal input. Step 1 Check the checkbox to select different signal input types: HD/CVBS and IP. Step 2 Click Apply to save the settings.
ATM Digital Video Recorder User Manual Figure 2-15 Configure Signal Input Type For detailed information of signal input, you can refer to Chapter 2.9 Configuring Signal Input Channel for reference. 2.4.2 Using the Wizard for Basic Configuration Purpose By default, the Setup Wizard starts once the device has loaded. You can follow it to complete the basic configuration. Selecting the language: Step 1 Select the language from the drop-down list. Step 2 Click Apply button.
ATM Digital Video Recorder User Manual Figure 2-17 Start Wizard Interface Step 2 Click Next button to enter the Date and Time Settings interface. Figure 2-18 Date and Time Settings Step 3 After the time settings, click Next button to enter the General Network Setup Wizard interface as shown below.
ATM Digital Video Recorder User Manual Figure 2-19 General Network Configuration If DHCP is enabled, you can check the checkbox of Enable DNS DHCP or uncheck it and edit the Preferred DNS Server and Alternate DNS Server. Step 4 Click Next button and you can enter the RAID configuration interface. Check the checkbox of Enable RAID to take this function into effect. Figure 2-20 RAID Configuration Step 5 Click Next button to enter the HDD Management interface as shown below.
ATM Digital Video Recorder User Manual Figure 2-21 HDD Management Step 6 Click Next button to enter the IP Camera Management interface. Step 7 Add the IP camera. 1) Click Search to search the online IP Camera. The Security status shows whether it is active or inactive. Before adding the camera, make sure the IP camera to be added is in active status. If the camera is in inactive status, you can click the inactive icon of the camera to set the password to activate it.
ATM Digital Video Recorder User Manual Click , and you can enable the continuous recording or motion detection recording for all channels of the device. Figure 2-23 Record Settings Step 9 Click OK to complete the wizard settings. 2.5 Login and Logout 2.5.1 User Login Purpose You have to log in to the device before operating the menu and other functions Step 1 Select the User Name in the drop-down list. Figure 2-24 Login Interface Step 2 Input the Password. Step 3 Click OK to log in.
ATM Digital Video Recorder User Manual Figure 2-25 User Account Protection for the Admin Figure 2-26 User Account Protection for the Operator 2.5.2 User Logout Purpose After logging out, the monitor turns to the live view mode and if you want to perform some operations, you need to enter the user name and password to log in again. Step 1 Enter the Shutdown menu. Menu > Shutdown Figure 2-27 Logout Step 2 Click Logout. After you have logged out of the system, menu operation on the screen is invalid.
ATM Digital Video Recorder User Manual Figure 2-28 Import GUID Step 2 Select the GUID file from the USB flash disk and click Import button to pop up the Reset Password interface. Figure 2-29 Reset Password Step 3 Input the new password and confirm the password. Step 4 Click OK to save the new password. Then the Attention box pops up as shown below.
ATM Digital Video Recorder User Manual Figure 2-31 Duplicate the Password If you want to retrieve the password when you forget it, you must export the GUID file first. Once the password is reset, the GUID file will be invalid. You can export a new GUID file. Refer to Chapter 17.5.3 Editing a User for reference. 2.7 Adding and Connecting the IP Cameras 2.7.1 Activating the IP Camera Purpose Before adding the camera, make sure the IP camera to be added is in active status.
ATM Digital Video Recorder User Manual Figure 2-33 Activate the Camera Step 3 Set the password of the camera to activate it. Use Admin Password: When you check the checkbox, the camera (s) will be configured with the same admin password of the operating DVR. Create New Password: If the admin password is not used, you must create the new password for the camera and confirm it.
ATM Digital Video Recorder User Manual Ensure the network connection is valid and correct. For detailed checking and configuring of the network, please see Chapter 12 Network Settings. OPTION 1: Step 1 Select the Add IP Camera option from the right-click menu in live view mode or click Menu> Camera> IP Camera to enter the IP Camera Management interface. Figure 2-35 IP Camera Management Interface Step 2 The online cameras with same network segment will be detected and displayed in the camera list.
ATM Digital Video Recorder User Manual Figure 2-36 Select Multiple Channels OPTION 2: Step 1 On the IP Camera Management interface, click the Custom Adding button to pop up the Add IP Camera (Custom) interface. Figure 2-37 Custom Adding IP Camera Interface Step 2 You can edit the IP address, protocol, management port, and other information of the IP camera to be added.
ATM Digital Video Recorder User Manual For the successfully added IP cameras, the Security status shows the security level of the password of camera: strong password, weak password and risky password. Figure 2-38 Successfully Added IP Cameras Please refer to specifications for the number of connectable IP cameras. Table 2-1 Explanation of the Icons Icon Explanation Icon Explanation Edit basic parameters of the camera Add the detected IP camera.
ATM Digital Video Recorder User Manual 2.7.3 Editing the Connected IP Camera Purpose After the adding of the IP cameras, the basic information of the camera is listed on the interface, and you can configure the basic settings of the IP cameras. Step 1 Click the icon to edit the parameters. You can edit the IP address, protocol and other parameters.
ATM Digital Video Recorder User Manual Figure 2-41 Password Configuration of the Camera Step 5 Click OK to save the settings and exit the interface. 2.8 Configuring Custom Protocols Purpose Custom protocols can be set for the network cameras which are not configured with the standard protocols. Step 1 Click Protocol on the Custom Adding interface to enter the Protocol Management interface.
ATM Digital Video Recorder User Manual Enable Sub-stream: If the network camera does not support sub-stream or the sub-stream is not needed, leave the checkbox empty. Type: The network camera adopting custom protocol must support getting stream through standard RTSP. Transfer Protocol: Select the transfer protocol for the custom protocol. Port: Set the port No. for the custom protocol. Path: Set the resource path for the custom protocol. E.g., ch1/main/av_stream.
ATM Digital Video Recorder User Manual If you select HD/CVBS, the analog signal inputs can be connected randomly for the selected channel. If you select IP, IP camera can be connected for the selected channel. Step 3 View the Max. IP Camera Number. Step 4 Click Apply to save the settings. Disabling one analog channel will add one IP channel. Up to 8 IP cameras can be added.
ATM Digital Video Recorder User Manual Chapter 3 Live View 3.1 Introduction of Live View Live view shows you the video image getting from each camera in real time. The DVR will automatically enter Live View mode when powered on. It is also at the very top of the menu hierarchy, thus hitting the ESC many times (depending on which menu you’re on) will bring you to the Live View mode.
ATM Digital Video Recorder User Manual Start Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen on the configuration menu before enabling the auto-switch. Menu>Configuration>Live View>Dwell Time. Start Recording: normal record and motion detection record are supported. Add IP Camera: the shortcut to the IP camera management interface. Output Mode: select the output mode to Standard, Bright, Gentle or Vivid.
ATM Digital Video Recorder User Manual Table 3-3 Mouse Operation in Live View Name Description Menu Enter the main menu of the system by right-clicking the mouse. Single Screen Switch to the single full screen by choosing channel number from the drop-down list. Multi-Screen Adjust the screen layout by selecting from the drop-down list. Previous Screen Switch to the previous screen. Next Screen Switch to the next screen. Enable/disable the auto-switch of the screens.
ATM Digital Video Recorder User Manual Display/Hide Transaction Information Enable/disable the overlay of transaction information. Figure 3-1 Right-Click Menu 3.2.2 Switching Main/Aux Output Purpose For DS-8104AHQLI-E4 and iDS-8104AHQXLI-E4, you can switch the main and auxiliary output. Step 1 Use the mouse wheel to double-click on the HDMI/VGA output screen, and the following message box pops up.
ATM Digital Video Recorder User Manual You can select the Menu Output Mode under Menu>Configuration>General>More Settings to Auto, HDMI/VGA and LCD (for DS-8104AHQLI-E4 and iDS-8104AHQXLI-E4) or Auto, and HDMI/VGA (for DS-8104AHQI-E4), and then reboot the device to switch the main output. 3.2.3 Quick Setting Toolbar in Live View Mode On the screen of each channel, there is a quick setting toolbar which shows when you click the screen.
ATM Digital Video Recorder User Manual Image Settings icon can be selected to enter the Image Settings menu. You can drag the mouse or click to adjust the image parameters, including brightness, contrast, and saturation. Refer to the Chapter 14.3 Configuring Video Parameters for details. Figure 3-5 Image Settings Move the mouse onto the Information icon to show the real-time stream information, including the frame rate, bit rate, resolution and stream type.
ATM Digital Video Recorder User Manual Figure 3-7 Live View-Channel-Zero Encoding Step 3 Check the checkbox of Enable Channel-Zero Encoding. Step 4 Configure the Frame Rate, Max. Bitrate Mode and Max. Bitrate. Step 5 Click Apply to activate the settings. After you set the channel-zero encoding, you can get a view of all the channels in the remote client or web browser in only one screen. 3.4 Adjusting Live View Settings Purpose Live view settings can be customized according to different needs.
ATM Digital Video Recorder User Manual Enable Audio Output: Enables/disables audio output for the selected camera in the live view mode. Volume: Adjust the volume of the audio output. Event Output: Designates the output to show event video. If available, you can select a different video output interface from the Video Output Interface when an event occurs. Full Screen Monitoring Dwell Time: The time in seconds to show alarm event screen. Step 2 Set the camera order.
ATM Digital Video Recorder User Manual Figure 3-10 Video Quality Diagnostics Step 2 Check the checkboxes to select the channels for diagnostics. Step 3 Click the button Diagnose, and the results will be displayed on a list. You can view the video status and diagnostics time of the selected channels. Figure 3-11 Diagnostics Result Connect the camera to the device for the video quality diagnostics. Three exception types can be diagnosed: Blurred Image, Abnormal Brightness and Color Cast.
ATM Digital Video Recorder User Manual Chapter 4 PTZ Controls 4.1 Configuring PTZ Settings Purpose Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before you control the PTZ camera. Before you start Make sure that the PTZ camera and the device are connected properly via RS-485 interface. Step 1 Enter the PTZ Settings interface. Menu >Camera> PTZ Figure 4-1 PTZ Settings Step 2 Select the camera for PTZ setting in the Camera drop-down list.
ATM Digital Video Recorder User Manual Figure 4-2 PTZ- General Step 4 Select the parameters of the PTZ camera from the drop-down list. All the parameters should be exactly the same as the PTZ camera parameters. For the Coaxitron camera/dome connected, you can select the PTZ protocol to HIKVISION-C (Coaxitron). Make sure the protocol selected here is supported by the connected camera/dome.
ATM Digital Video Recorder User Manual Step 7 (Optional) Check the checkbox of Enable Omnicast Control to enable the PTZ control of the selected camera via Omnicast VMS of Genetec. 4.2 Setting PTZ Presets, Patrols and Patterns Before you start Please make sure that the presets, patrols and patterns should be supported by PTZ protocols. 4.2.1 Customizing Presets Purpose Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place.
ATM Digital Video Recorder User Manual 4.2.2 Calling Presets Purpose This feature enables the camera to point to a specified position such as a window when an event takes place. Step 1 Click the button PTZ in the lower-right corner of the PTZ setting interface; Or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar, or select the PTZ option in the right-click menu to show the PTZ control panel. Step 2 Choose Camera in the drop-down list.
ATM Digital Video Recorder User Manual Figure 4-6 PTZ Settings Step 2 Select patrol No. in the drop-down list of patrol. Step 3 Click the Set button to add key points for the patrol. Figure 4-7 Key point Configuration Step 4 Configure key point parameters, such as the key point No., duration of staying for one key point and speed of patrol. The key point is corresponding to the preset. The Key Point No. determines the order at which the PTZ will follow while cycling through the patrol.
ATM Digital Video Recorder User Manual Step 1 Click the button PTZ in the lower-right corner of the PTZ Settings interface; Or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar, or select the PTZ option in the right-click menu to show the PTZ control panel. Step 2 Click the General tab to show the general settings of the PTZ control. Figure 4-8 PTZ Panel - General Step 3 Select a patrol in the drop-down list and click the Call Patrol button to call it.
ATM Digital Video Recorder User Manual Figure 4-9 PTZ Settings Step 2 Choose pattern number in the drop-down list. Step 3 Click the Start button and click corresponding buttons in the control panel to move the PTZ camera, and click the Stop button to stop it. The movement of the PTZ is recorded as the pattern. 4.2.6 Calling Patterns Purpose Follow the procedure to move the PTZ camera according to the predefined patterns.
ATM Digital Video Recorder User Manual Figure 4-10 PTZ Panel - General Step 3 Click the Call Pattern button to call it. Step 4 Click the Stop Pattern button to stop calling it. 4.2.7 Customizing Linear Scan Limit Purpose The Linear Scan can be enabled to trigger the scan in the horizantal direction in the predefined range. This function is supported by some certain models. Step 1 Enter the PTZ Settings interface.
ATM Digital Video Recorder User Manual Figure 4-11 PTZ Settings Step 2 Use the directional button to wheel the camera to the location where you want to set the limit, and click the Left Limit or Right Limit button to link the location to the corresponding limit. The speed dome starts linear scan from the left limit to the right limit, and you must set the left limit on the left side of the right limit, as well the angle from the left limit to the right limit should be no more than 180º. 4.2.
ATM Digital Video Recorder User Manual Figure 4-12 PTZ Panel - One-touch Step 3 Click Linear Scan button to start the linear scan and click the Linear Scan button again to stop it. You can click the Restore button to clear the defined left limit and right limit data and the dome needs to reboot to make settings take effect. 4.2.9 One-Touch Park Purpose For some certain model of the speed dome, it can be configured to start a predefined park action (scan, preset, patrol and etc.
ATM Digital Video Recorder User Manual Step 3 There are 3 one-touch park types selectable. Click the corresponding button to activate the park action. Park (Quick Patrol): The dome starts patrol from the predefined preset 1 to preset 32 in order after the park time. The undefined preset will be skipped. Park (Patrol 1): The dome starts moving according to the predefined patrol 1 path after the park time. Park (Preset 1): The dome moves to the predefined preset 1 location after the park time.
ATM Digital Video Recorder User Manual Figure 4-14 PTZ Control Panel You can refer to Table 4-1 for the description of the PTZ panel icons.
ATM Digital Video Recorder User Manual Chapter 5 Recording and Capture Settings 5.1 Configuring Encoding Parameters Before you start Step 1 Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. (Menu>HDD>General) Figure 5-1 HDD-General Step 2 Click Advanced tab to check the storage mode of the HDD. (Menu>HDD>Advanced>Storage Mode) 1) If the HDD mode is Quota, please set the maximum record capacity. For detailed information, see Chapter 13.
ATM Digital Video Recorder User Manual Figure 5-3 Record Parameters Step 2 Set the parameters for recording. 1) Select the Record tab to configure. 2) Select a camera from the camera drop-down list. 3) View the Camera Resolution. 4) Configure the following parameters for the Main Stream (Continuous) and the Main Stream (Event). Stream Type: Set the stream type to be Video or Video & Audio. Resolution: Set recording resolution. Up to 3 MP resultion is supported for the analog channels.
ATM Digital Video Recorder User Manual Max Bitrate (Kbps): Select or customize the maximum bit rate for recording. Max. Bitrate Range Recommended: A recommended max. bit rate range is provided for reference. Step 3 Check the checkbox of Enable H.264+ to enable this function. Enabling it helps to ensure the high video quality with a lowered bitrate. After enabling H.264+, the Bitrate Type, Video Quality, Max. Bitrate Mode, Max. Bitrate(Kbps) and Max. Bitrate Range Recommend are not configurable.
ATM Digital Video Recorder User Manual The Redundant Record option is only available when the HDD mode is Group. Redundant HDD is required for the redundant record function. For detailed information, see Chapter 14.3.2 Setting HDD Property. For network cameras, the parameters of Main Stream (Event) are not editable. Step 5 Click Apply to save the settings. Step 6 (Optional) Click Copy to copy the settings to other analog channels if needed.
ATM Digital Video Recorder User Manual Figure 5-7 Capture Settings 2) Select a camera in the camera drop-down list. 3) Configure the parameters. 4) Click Apply to save the settings. 5) (Optional) If the parameters can also be used to other cameras, click Copy to copy the settings to other channels. The interval is the time period between two capturing actions. You can configure all the parameters on this menu on your demand. 5.
ATM Digital Video Recorder User Manual Figure 5-8 Record Schedule Different recording types are marked in different color icons. Continuous: scheduled recording. Event: recording triggered by all event triggered alarm. Motion: recording triggered by motion detection. Alarm: recording triggered by alarm. M | A: recording triggered by either motion detection or alarm. M & A: recording triggered by motion detection and alarm. Command: recording triggered by ATM command.
ATM Digital Video Recorder User Manual Figure 5-9 Edit Schedule- All Day 4) To arrange other schedule, leave the All Day checkbox blank and set the Start/End time. Figure 5-10 Edit Schedule- Set Time Period Up to 8 periods can be configured for each day. And the time periods cannot be overlapped with each other. To enable Event, Motion, Alarm, M | A (motion or alarm), M & A (motion and alarm) triggered recording, you must configure the motion detection settings, or alarm input settings as well.
ATM Digital Video Recorder User Manual Figure 5-11 Copy Schedule to Other Days The Holiday option is available when you enable holiday schedule in Holiday settings. See Chapter 5.7 Configuring Holiday Record. 6) Click OK to save setting and back to upper level menu. Draw the schedule 1) Click on the color icon to select a record type in the event list on the right-side of the interface.
ATM Digital Video Recorder User Manual Figure 5-13 Draw the Capture Schedule 2) Drag the mouse on the schedule. 3) Click on the other area except for the schedule table to finish and exit from the drawing. You can repeat step 4 to set schedule for other channels. If the settings can also be used to other channels, click Copy, and then select the channel to which you want to copy to. Step 5 Click Apply to save the settings. 5.
ATM Digital Video Recorder User Manual Figure 5-14 Motion Detection Step 2 Configure Motion Detection: 1) Select the camera you want to configure. 2) Check the checkbox of Enable Motion Detection. 3) Drag and draw the area for motion detection by mouse. If you want to set the motion detection for all the area shot by the camera, click Full Screen. To clear the motion detection area, click Clear. Figure 5-15 Motion Detection- Mask 4) Click , and the message box for channel information pops up.
ATM Digital Video Recorder User Manual Figure 5-16 Motion Detection Settings 5) Select the channels which you want the motion detection event to trigger recording. 6) Click Apply to save the settings. 7) Click OK to return to the upper level menu. 8) Click Apply in the Motion Detection interface to save the settings. Exit from the Motion Detection interface. Step 3 Configure the schedule. Please refer to the step 4 of Chapter 5.
ATM Digital Video Recorder User Manual Figure 5-17 Alarm Settings Step 2 Click Alarm Input tab. Figure 5-18 Alarm Settings- Alarm Input Step 3 Select Alarm Input No. Step 4 Input Alarm Name. Step 5 Select N.O (normally open) or N.C (normally closed) for alarm type. Step 6 Check the checkbox of Enable to enable alarm. Step 7 Click after Settings to set the triggered channels, arming schedule, linkage actions, PTZ linking, and camera of smart ATM mode. Refer to step 4 of Chapter 5.
ATM Digital Video Recorder User Manual Figure 5-19 Alarm Handling Step 8 Click Apply to save the settings. Repeat the steps from 1 to 8 to configure other alarm input parameters. If the settings can also be applied to other alarm inputs, click Copy and select the alarm input number. Figure 5-20 Copy Alarm Input Step 9 Configure the schedule. Please refer to the step 4 of Chapter 5.2 Configuring Recording and Capture Schedule, while you need to select Alarm as the record type.
ATM Digital Video Recorder User Manual 5.5 Configuring Command Triggered Recording and Capture Before you start Connect the device to the ATM machine properly. Purpose When some transaction behaviors, such as Card In, Withdrawal, Query, etc., occur on the ATM machine, the recording/capture process will be triggered. Step 1 Enter the ATM Settings interface. Menu > Configuration > ATM Figure 5-21 ATM Settings Step 2 Select the ATM from the drop-down list and check the checkbox of Enable ATM.
ATM Digital Video Recorder User Manual Figure 5-22 Manual Record Step 2 Enable manual record. Click the status icon before camera No. to change it to Or click the status icon . of Analog or IP Camera to enable manual record of all channels. Step 3 Disable manual record. Click the status icon Or click the status icon to change it to . of Analog or IP Camera to disable manual record of all channels. After rebooting all the manual records enabled are canceled.
ATM Digital Video Recorder User Manual Figure 5-25 Smart ATM Recording 2) Click Yes to enable all-day continuous recording, all-day motion detection recording, or all-day smart ATM recording of all channels. Step 5 Configure continuous capture. 1) Click Continuous Capture tab on the left bar. Figure 5-26 Continuous Capture 2) Click the status button before camera No. to change capture. 3) Click the status button to change to to to enable continuous to disable continuous capture.
ATM Digital Video Recorder User Manual Figure 5-27 Holiday Settings Step 3 Enable Edit Holiday schedule. 1) Click to enter the Edit interface. Figure 5-28 Edit Holiday Settings 2) Check the checkbox of Enable. 3) Select Mode from the drop-down list. There are three different modes for the date format to configure holiday schedule. By Month, By Week, and By Date are selectable. 4) Set the start and end date. 5) Click Apply to save settings. 6) Click OK to exit the Edit interface.
ATM Digital Video Recorder User Manual Figure 5-29 Edit Schedule- Holiday Up to 8 periods can be configured for each day. And the time periods cannot be overlapped each other. In the time table of the channel, both holiday schedule and normal day schedule are displayed. Repeat the above step 4 to set Holiday schedule for other channels. If the holiday schedule can also be used to other channels, click Copy and choose the channel you want to apply the settings. 5.
ATM Digital Video Recorder User Manual 1) Set the HDD property to Redundant. Figure 5-31 HDD General-Editing 2) Click Apply to save the settings. 3) Click OK to back to the upper level menu. Step 3 Enter the Record setting interface. Menu> Record> Parameters 1) Select the Record tab. 2) Select Camera you want to configure. 3) Click More Settings button. Figure 5-32 More Settings 4) Check the checkbox of Redundant Record. 5) Click OK to save the settings.
ATM Digital Video Recorder User Manual 5.9 Configuring HDD Group Purpose You can group the HDDs and save the record files in certain HDD group. Step 1 Enter HDD setting interface. Menu>HDD>Advanced Step 2 Select Storage Mode tab. Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information, please refer to Chapter 13.3 Managing HDD Group. Step 3 Select General in the left bar. Click to enter editing interface. Step 4 Configuring HDD group.
ATM Digital Video Recorder User Manual 2) Select Group number in the drop-down list of Record on HDD Group 3) Check the channels you want to save in this group. 4) Click Apply to save settings. After you have configured the HDD groups, you can configure the recording settings following the procedure provided in Chapter 5.2-5.7. 5.10 Files Protection Purpose You can lock the recorded files or set the HDD property to Read-only to protect the record files from being overwritten.
ATM Digital Video Recorder User Manual Figure 5-35 Export-Search Result Step 5 Protect the record files. 1) Find the record files you want to protect, and then click the indicating that the file is locked. icon which will turn to The record files of which the recording is still not completed cannot be locked. 2) Click to change it to to unlock the file and the file is not protected.
ATM Digital Video Recorder User Manual Figure 5-37 HDD General- Editing Step 3 Set the HDD to Read-only. Step 4 Click OK to save settings and back to the upper level menu. You cannot save any files in a Read-only HDD. If you want to save files in the HDD, change the property to R/W. If there is only one HDD and is set to Read-only, the DVR cannot record any files. Only live view mode is available.
ATM Digital Video Recorder User Manual Figure 5-39 Attention Box Step 4 Click Yes to enable the function and reboot the device to have new settings taken effect. If H.264+ is already enabled for all the analog cameras, when you click Enable button, the following attention box pops up to remind you that H.264+ is already enabled for all analog cameras. Figure 5-40 Attention Box Task 2: One-Key Disabling H.
ATM Digital Video Recorder User Manual Figure 5-43 Attention Box 93
ATM Digital Video Recorder User Manual Chapter 6 Playback 6.1 Playing Back Record Files 6.1.1 Instant Playback Purpose Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported. Instant playback by channel Select a channel in live view mode and click the button in the quick setting toolbar. In the instant playback mode, only record files recorded during the last five minutes on this channel will be played back. Figure 6-1 Instant Playback Interface 6.1.
ATM Digital Video Recorder User Manual Figure 6-2 Right-Click Menu in Live View Playback by Time Purpose Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch are supported. Step 1 Enter Playback interface. Menu>Playback Step 2 Check the checkbox of channel in the channel list and then double-click to select a date on the calendar.
ATM Digital Video Recorder User Manual You can also use the toolbar in the bottom part of Playback interface to control playing progress, as shown in the following figure. Figure 6-4 Playback Interface Select the channel(s) if you want to switch playback to another channel or execute simultaneous playback of multiple channels.
ATM Digital Video Recorder User Manual Button Operation Button Operation Button Operation play/Pause 30s forward 30s reverse Fast forward Previous day Slow forward Full Screen Exit Next day Process bar Scaling up/down time line Save the clips / / / Pause/Play the Display/Hide transaction information The indicates the start time and end time of the record files.
ATM Digital Video Recorder User Manual Figure 6-6 Video Search by ATM Information Step 3 Check the checkbox of the channel in the channel list, and specify the start and end time for search. Step 4 Click ATM in the lower-right corner to enter the ATM Settings interface. 1) Input the Card No., Transaction Amount and then select the Transaction Type from the drop-down list for video search. 2) Click OK to save the settings.
ATM Digital Video Recorder User Manual Figure 6-7 ATM Parameters Step 5 Click Search, and the record files matching the search conditions will be displayed on a list. Figure 6-8 Result of Video Search by ATM Information Step 6 Click to play back the record files. You can click Back to return to the search interface.
ATM Digital Video Recorder User Manual Figure 6-9 Interface of Playback by ATM Information 6.1.4 Playing Back by Event Search Purpose Play back record files on one or several channels searched out by restricting event types (motion detection or alarm input). Channel switch is supported. For DS-8104AHQ(L)I-E4, motion detection and alarm input can be selected for the event types. For iDS-8104AHQXLI-E4, motion detection, alarm input, and smart ATM alarm can be selected for the event types.
ATM Digital Video Recorder User Manual Figure 6-10 Video Search by Motion Detection Step 4 Click Search, and the record files matching the search conditions will be displayed on a list. Step 5 Select and click to play back the record files. You can click Back button to return to the search interface. If there is only one channel triggered, click channel. to realize full-screen playback of this If several channels are triggered, click to enter the Synchronous Playback interface.
ATM Digital Video Recorder User Manual Figure 6-12 Interface of Playback by Event Pre-play and post-play can be configured for the playback of event triggered record files. Pre-play: The time you set to play back before the event. For example, when an alarm triggered the recording at 10:00, if you set the pre-play time as 5 seconds, the video plays back from 9:59:55. Post-play: The time you set to play back after the event.
ATM Digital Video Recorder User Manual Figure 6-13 Interface of Playback by Time Step 3 Click to add default tag. Step 4 Click to add customized tag and input tag name. Figure 6-14 Add Tag Max. 64 tags can be added to a single video file. Step 5 Click to check, edit and delete tag(s).
ATM Digital Video Recorder User Manual Figure 6-15 Tag Management Interface Steps Step 1 Select Tag from the drop-down list in the Playback interface. Step 2 Select channels, edit start time and end time, and then click Search to enter Search Result interface. You can enter keyword in the textbox to search the tag on your command. Figure 6-16 Video Search by Tag Step 3 Click to play back the file. You can click Back to return to the search interface.
ATM Digital Video Recorder User Manual Pre-play and post-play can be configured. You can click or to select the previous or next tag. Please refer to Table 6-1 for the description of buttons on the toolbar. 6.1.6 Playing Back by System Logs Purpose Play back record file(s) associated with channels after searching system logs. Step 1 Enter Log Search interface. Menu>Maintenance>Log Information>Log Search Figure 6-17 System Log Search Interface Step 2 Set search time and type and click Search.
ATM Digital Video Recorder User Manual Figure 6-18 Result of System Log Search Step 3 Select a log with record file and click to enter Playback interface. If there is no record file at the time point of the log, the message box “No result found” will pop up. Step 4 Playback management. The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6-19 Interface of Playback by Log 6.1.
ATM Digital Video Recorder User Manual Step 3 Select a date and start playing the video file. Step 4 Select the Split-screen Number from the drop-down list. Up to 4 screens are configurable. Figure 6-20 Interface of Sub-periods Playback According to the defined number of split-screens, the video files on the selected date can be divided into average segments for playback. E.g.
ATM Digital Video Recorder User Manual Figure 6-21 Interface of External File Playback 6.1.9 Playing Back Pictures Purpose The captured pictures stored in the HDDs of the device can be searched and viewed. Step 1 Enter Playback interface. Menu>Playback Step 2 Select Picture from the drop-down list in the upper-left corner of the page to enter the Picture Playback interface. Step 3 Check the checkbox to select the channel and specify the start time and end time for search.
ATM Digital Video Recorder User Manual Figure 6-22 Result of Picture Playback Step 6 The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6-23 Picture Playback Toolbar Table 6-2 Detailed Explanation of Picture-playback Toolbar Button Function Play reverse Button Function Button Function Previous picture Play Button Function Next picture 6.2 Auxiliary Functions of Playback 6.2.
ATM Digital Video Recorder User Manual 6.2.2 Digital Zoom Step 1 Click the button on the playback control bar to enter Digital Zoom interface. Step 2 Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times. Figure 6-24 Draw Area for Digital Zoom Step 3 Right-click the image to exit the digital zoom interface. 6.2.3 Reverse Playback of Multi-Channel Purpose You can play back record files of multi-channel reversely.
ATM Digital Video Recorder User Manual Figure 6-25 4-ch Synchronous Playback Interface Step 3 Click to play back the record files reversely.
ATM Digital Video Recorder User Manual Chapter 7 Backup 7.1 Backing up Record Files Before you start Please insert the backup device(s) into the device. 7.1.1 Quick Export Purpose Export record files to backup device(s) quickly. Step 1 Enter Normal Export interface. Menu > Export > Normal Step 2 Select the channel(s) you want to back up and set the search conditions. The start time and end time for search should be within the same day.
ATM Digital Video Recorder User Manual Figure 7-2 Quick Export Using USB1-1 Step 4 Select the backup device from the drop-down list and click Export. The record files within the start time and end time will be exported to the external storage device (e.g., USB Flash Drive) after the backup process is complete. The Player program player.exe will be exported automatically during record file export.
ATM Digital Video Recorder User Manual Backup using USB flash drives and USB HDDs Step 1 Enter Export interface. Menu>Export>Normal/Picture Step 2 Select the cameras to search. Step 3 Set search condition and click Search to enter the search result interface. Figure 7-4 Normal Video Search for Backup Step 4 The matched video files are displayed in Chart or List display mode. Click to play the record file if you want to check it. Check the checkbox before the video files you want to back up.
ATM Digital Video Recorder User Manual Figure 7-5 Result of Normal Video Search for Backup Step 5 Select video files from the Chart or List to export, and click Export to enter the Export interface. You can also click Export All to select all the video files for backup and enter the Export interface.
ATM Digital Video Recorder User Manual Figure 7-7 Export Finished The backup of pictures using USB writer or SATA writer has the same operating instructions. Please refer to steps described above. 7.1.3 Backing up by Event Search Purpose Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or eSATA HDD. Quick Backup and Normal Backup are supported. Step 1 Enter Export interface. Menu > Export > Event Step 2 Select the cameras to search.
ATM Digital Video Recorder User Manual Step 5 Select video files from the Chart or List interface to export. Figure 7-9 Result of Event Search Step 6 Export the video files. Please refer to step 5 of Chapter 7.1.2 Backing up by Normal Video/Picture Search for details. 7.1.4 Backing up Video Clips Purpose You may also select video clips in playback mode to export directly during Playback, using USB devices (USB flash drives, USB HDDs, USB writer), or SATA writer. Step 1 Enter Playback interface.
ATM Digital Video Recorder User Manual Step 4 Export the video clips in playback. Please refer to step 5 of Chapter 7.1.2 Backing up by Normal Video/Picture Search for details. 7.2 Managing Backup Devices Step 1 Enter the Export interface. Figure 7-11 Storage Device Management Step 2 Backup device management. 1) Click New Folder if you want to create a new folder in the backup device. 2) Select a record file or folder in the backup device and click if you want to delete it.
ATM Digital Video Recorder User Manual Chapter 8 Alarm Settings 8.1 Setting Motion Detection Step 1 Enter Motion Detection interface of Camera Management. Menu> Camera> Motion Figure 8-1 Motion Detection Setup Interface Step 2 Select a camera you want to set up motion detection. Step 3 Check checkbox to enable motion detection. Step 4 Set detection area and sensitivity.
ATM Digital Video Recorder User Manual 1) Click Trigger Channel tab and select one or more channels which will start to record or become full-screen monitoring when motion alarm is triggered. Figure 8-3 Set Trigger Camera of Motion Detection 2) Select Arming Schedule tab to set the channel’s arming schedule. Select one day of a week and up to eight time periods can be set within each day. Or you can click the Copy button to copy the time period settings to other day(s).
ATM Digital Video Recorder User Manual 8.2 Setting Sensor Alarms Purpose Set up handling method of an external sensor alarm. Step 1 Enter Alarm Input Settings interface. Menu > Configuration > Alarm > Alarm Input Figure 8-5 Alarm Input Settings Interface Step 2 Select the alarm input. Step 3 Check the Enable checkbox and click to set its alarm response actions.
ATM Digital Video Recorder User Manual Time periods shall not be repeated or overlapped. 3) Select Linkage Action tab to set up alarm response actions of the alarm input (Refer to Chapter 8.7 Setting Alarm Response Actions). 4) (Optional) Select PTZ Linking tab and set PTZ linkage of the alarm input. Set PTZ linking parameters and click OK to complete the settings of the alarm input. 5) (Optional) Select Camera of Smart ATM Mode tab to select the camera enabled smart ATM.
ATM Digital Video Recorder User Manual Figure 8-8 Copy Settings of Alarm Input 8.3 Detecting Video Loss Purpose Detect video loss of a channel and take alarm response action(s). Step 1 Enter Video Loss interface of Camera Management. Menu> Camera> Video Loss Figure 8-9 Video Loss Setup Interface Step 2 Select a channel you want to detect. Step 3 Check the checkbox of Enable Video Loss Alarm. Step 4 Click to set up handling method of video loss.
ATM Digital Video Recorder User Manual Select one day of a week and up to eight time periods can be set within each day. Or you can click Copy to copy the time period settings to other day(s). Time periods shall not be repeated or overlapped. Figure 8-10 Set Arming Schedule of Video Loss 2) Select Linkage Action tab to set up alarm response actions of video loss (Refer to Chapter 8.7 Setting Alarm Response Actions). 3) Click OK to complete the video loss settings of the channel.
ATM Digital Video Recorder User Manual Figure 8-11 Video Tampering Interface Step 2 Select a channel you want to detect video tampering. Step 3 Check the checkbox of Enable Video Tampering Detection. Step 4 Drag the sensitivity bar to set a proper sensitivity level. Step 5 Click to set handling method of video tampering. 1) Click Arming Schedule tab to set the arming schedule of response action. Select one day of a week and up to eight time periods can be set within each day.
ATM Digital Video Recorder User Manual Step 6 Repeat the above steps to finish settings of other channels, or click Copy to copy the above settings to them. Step 7 Click Apply to save the settings. 8.5 Setting All-day Video Quality Diagnostics Purpose The device provides two ways to diagnose the video quality: manual and all-day. Perform the following steps to set the threshold of the diagnosing and the linkage actions. Step 1 Enter Video Quality Diagnostics Settings interface of Camera Management.
ATM Digital Video Recorder User Manual Select one day of a week and up to eight time periods can be set within each day. Or you can click Copy to copy the time period settings to other day(s). Time periods shall not be repeated or overlapped. Figure 8-14 Set Arming Schedule of Video Quality Diagnostics 2) Select Linkage Action tab to set alarm response actions of video quality diagnostics alarm (Refer to Chapter 8.7 Setting Alarm Response Actions).
ATM Digital Video Recorder User Manual Record/Capture Exception: No space for saving recorded files or captured pictures. Step 1 Enter Exceptions interface and handle various exceptions. Menu> Configuration> Exceptions Figure 8-15 Exception Settings Interface Step 2 Check the checkbox of Enable Event Hint to display exceptional event occurs. Step 3 Click (Event/Exception icon) when an to select the detailed event hint for display.
ATM Digital Video Recorder User Manual Figure 8-17 Detailed Event Step 4 Select the Exception Type. Step 5 Check the checkbox to set the alarm linkage actions. For details, refer to Chapter 8.7 Setting Alarm Response Actions. Step 6 Click Apply to save the settings. 8.7 Setting Alarm Response Actions Purpose Alarm response actions will be activated when an alarm or exception occurs, including Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Send Email and Trigger Alarm Output.
ATM Digital Video Recorder User Manual Sends an exception or alarm signal to remote alarm host when an event occurs. The alarm host refers to the PC installed with Remote Client. The alarm signal will be transmitted automatically at detection mode when remote alarm host is configured. Please refer to Chapter 12.2.6 Configuring More Settings for details of alarm host configuration. Send Email Send an email with alarm information to a user or users when an alarm is detected. Please refer to Chapter 12.2.
ATM Digital Video Recorder User Manual Figure 8-19 Set Arming Schedule of Alarm Output 2) Repeat step 1) to set arming schedule of other days of a week. Or click Copy to copy an arming schedule to other days. 3) Click OK to complete the arming schedule setting of alarm output. Step 3 Repeat the above steps to finish settings of other alarm outputs, or click Copy to copy the above settings to them. Step 4 Click Apply to save the settings.
ATM Digital Video Recorder User Manual Chapter 9 Smart ATM Settings For iDS-8104AHQXLI-E4 ATM DVR, you can enable smart ATM function. Four smart ATM modes are supported: panel mode, environment mode, human face mode, and safety cabin mode. The ATM DVR supports up to 4-ch smart ATM configuration of panel mode, environment mode, human face mode, and safety cabin mode together; up to 2-ch human face mode, or up to 2-ch safety cabin, or up to 1-ch human face mode and 1-ch safety cabin mode together.
ATM Digital Video Recorder User Manual Figure 9-1 Panel Mode Step 4 Configure Smart ATM Capture. 1) Click Smart ATM Capture. 2) Configure the captured picture parameters in panel mode. 3) Click Apply to save the settings. Figure 9-2 Picture Configuration Step 5 Configure Target Overlay.
ATM Digital Video Recorder User Manual 1) Click Target Overlay. 2) Check Display Target Info. on Alarm Picture or Display Rule Info. on Alarm Picture. Once they are checked, the target or rule information will be overlaid on the captured picture. 3) Click Apply to save the settings. Figure 9-3 Target Overlay Configuration Step 6 Configure Scene Description. 1) Click Scene Description. 2) Configure the scene parameters in panel mode. Mounting Location: The mounting location of the camera.
ATM Digital Video Recorder User Manual Figure 9-4 Scene Description Step 7 (Optional) Configure the shield region. You can configure shield regions to shield the influence of the configured rules towards the regions. The region easily influenced by light interference can be configured as the shield region to avoid false alarm. Up to four shield regions can be configured and enabled together. 1) Select a shield region from Select Shield Region drop-down list. 2) Click Draw Shield Region.
ATM Digital Video Recorder User Manual 4) Click OK to save the settings. Figure 9-5 Rule Configuration Rules of different types can be enabled together for the panel mode. Step 9 Draw the rule region. 1) Select a rule. 2) Click the buttons to draw the rule region. If you select Human Entrance, click Draw Entrance Region to draw the region. If you select Operation Timeout, Sticking Scrip, and Installing Scanner, click Draw Rectangular Frame, Draw Polygon, or Full Screen to draw the region.
ATM Digital Video Recorder User Manual Figure 9-6 Alarm Response Actions Configuration Step 11 Click Apply in Smart ATM Configuration interface to save the settings. 9.2 Environment Mode Purpose Environment mode supports the following smart ATM protection rule types: line crossing, region entrance, region exiting, intrusion, loitering, objects removal or unattended baggage, violent motion, tailing, falling down, and sudden change of sound intensity. Eight rules can be set for the mode.
ATM Digital Video Recorder User Manual Figure 9-7 Environment Mode Step 4 Configure Smart ATM Capture. Refer to step 4 of Chapter 9.1 Panel Mode for details. Step 5 Configure Target Overlay. Refer to step 5 of Chapter 9.1 Panel Mode for details. Step 6 (Optional) Configure the shield region. Refer to step 7 of Chapter 9.1 Panel Mode for details. Step 7 Select a rule and click to configure the rule. 1) Edit Name. 2) Select Type.
ATM Digital Video Recorder User Manual Figure 9-8 Rule Configuration Rules of different types can be enabled together for the environment mode. Step 8 Draw the rule region. Refer to step 9 of Chapter 9.1 Panel Mode for details. Step 9 Configure the alarm response actions. Refer to step 10 of Chapter 9.1 Panel Mode for details. Step 10 Click Apply in Smart ATM Configuration interface to save the settings. 9.
ATM Digital Video Recorder User Manual Figure 9-9 Human Face Mode Step 4 Configure Smart ATM Capture. Refer to step 4 of Chapter 9.1 Panel Mode for details. Step 5 (Optional) Configure the shield region. Refer to step 7 of Chapter 9.1 Panel Mode for details. Step 6 Select the rule and click to configure the rule. 1) Edit Name. 2) Check Type. Normal Human Face, Abnormal Human Face, Multiple Human Faces, Wearing Sunglasses, and Using Mobile Phone are selectable.
ATM Digital Video Recorder User Manual Figure 9-10 Rule Configuration Step 7 Draw the rule region. 1) Click Draw Max. Size to draw the maximum size of the human face. 2) Click Draw Min. Size to draw the minimum size of the human face. The max. face size should be larger than the min. face size. Step 8 Configure the alarm response actions. Refer to step 10 of Chapter 9.1 Panel Mode for details. Step 9 Click Apply in Smart ATM Configuration interface to save the settings. 9.
ATM Digital Video Recorder User Manual Figure 9-11 Safety Cabin Mode Step 4 Configure Smart ATM Capture. Refer to step 4 of Chapter 9.1 Panel Mode for details. Step 5 Configure Target Overlay. Refer to step 5 of Chapter 9.1 Panel Mode for details. Step 6 Configure Scene Description. 1) Click Scene Description. 2) Configure the scene parameters in safety cabin mode. Mounting Height: The mounting height of the camera.
ATM Digital Video Recorder User Manual Figure 9-12 Scene Description Step 7 (Optional) Configure the shield region. Refer to step 7 of Chapter 9.1 Panel Mode for details. Step 8 Select the rule and click to configure the rule. 1) Edit Name. 2) Select Type. Intrusion, Object Removal or Unattended Baggage, Violent Motion, Tailing, Falling Down, and Sudden Change of Sound Intensity are selectable. 3) Configure other parameters according to the selected type. 4) Click OK to save the settings.
ATM Digital Video Recorder User Manual Rules of different types can be enabled together for the safety cabin mode. Step 9 Draw the rule region. Refer to step 9 of Chapter 9.1 Panel Mode for details. Step 10 Configure the alarm response actions. Refer to step 10 of Chapter 9.1 Panel Mode for details. Step 11 Click Apply in Smart ATM Configuration interface to save the settings.
ATM Digital Video Recorder User Manual Chapter 10 Network Settings 10.1 Configuring General Settings Purpose Network settings must be properly configured before you operate the device over network. Step 1 Enter the Network Settings interface. Menu > Configuration > Network > General Figure 10-1 Network Settings Interface Step 2 Configure the following parameters: Working Mode, NIC Type, IPv4 Address, IPv4 Gateway, MTU, DNS Server and Main NIC.
ATM Digital Video Recorder User Manual The valid value of MTU is from 500 to 1500. If the DHCP server is available, you can check the checkbox of Enable DHCP to automatically obtain an IP address and other network settings from that server. If DHCP is enabled, you can check the checkbox of Enable DNS DHCP or uncheck it and edit the Preferred DNS Server and Alternate DNS Server. Step 3 Click Apply to save the settings. 10.2 Configuring Advanced Settings 10.2.
ATM Digital Video Recorder User Manual Step 1 Enter the Network Settings interface. Menu > Configuration > Network Step 2 Select the DDNS tab to enter the DDNS Settings interface. Step 3 Check the Enable DDNS checkbox to enable this feature. Step 4 Select DDNS Type. 5 different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP and HiDDNS. IPServer Enter Server Address for IPServer, and other fields are read only. The Server Address should be the IP address of the PC that runs IPServer.
ATM Digital Video Recorder User Manual Figure 10-5 PeanutHull Settings Interface NO-IP: Enter the account information in the corresponding fields. Refer to the DynDNS settings. 1) Enter Server Address for NO-IP. 2) In the Device Domain Name text field, enter the domain obtained from the NO-IP website (www.no-ip.com). 3) Enter the User Name and Password registered in the NO-IP website. Figure 10-6 NO-IP Settings Interface HiDDNS: The Server Address of the HiDDNS server appears by default: www.
ATM Digital Video Recorder User Manual Figure 10-7 HiDDNS Settings Interface Register the device on the HiDDNS server. 1) Go to the HiDDNS website: www.hik-online.com. Figure 10-8 Login Interface 2) Click log in.
ATM Digital Video Recorder User Manual Figure 10-9 Register an Account 3) In the Device Management interface, click to register the device. Figure 10-10 Register the Device 4) Input Device Serial No., Device Domain (Device Name) and HTTP Port. And click OK to add the device. Access the Device via Web Browser or Client Software After having successfully registered the device on the HiDDNS server, you can access your device via web browser or Client Software with the Device Domain (Device Name).
ATM Digital Video Recorder User Manual Example: http://www.hik-online.com/nvr If you mapped the HTTP port on your router and changed it to port No. except 80, you have to enter http://www.hik-online.com/alias:HTTP port in the address bar to access the device. You can refer to Chapter 12.2.7 Configuring HTTPS Port for the mapped HTTP port No.. OPTION 2: Access the devices via iVMS-4200 For iVMS-4200, in the Add Device window, select information.
ATM Digital Video Recorder User Manual Figure 10-12 NTP Settings Interface Step 3 Check the Enable NTP checkbox to enable this feature. Step 4 Configure the following NTP settings: Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute. NTP Server: IP address of NTP server. NTP Port: Port of NTP server. Step 5 Click Apply to save the settings and exit from the interface.
ATM Digital Video Recorder User Manual Figure 10-13 UPnP™ Settings Interface Step 3 Check Enable UPnP checkbox to enable UPnP™. Step 4 Select the Mapping Type as Manual or Auto in the drop-down list. OPTION 1: Auto If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router automatically. 1) Click Apply button to save the settings. 2) You can click Refresh button to get the latest status of the port mapping.
ATM Digital Video Recorder User Manual Figure 10-15 External Port Settings Dialog Box 2) Click Apply button to save the settings. 3) You can click Refresh button to get the latest status of the port mapping. Figure 10-16 UPnP™ Settings Finished-Manual 10.2.5 Configuring More Settings Step 1 Enter the Network Settings interface. Menu > Configuration > Network Step 2 Select the More Settings tab to enter the More Settings interface.
ATM Digital Video Recorder User Manual range of 224.0.0.0 to 239.255.255.255. It is recommended to use the IP address ranging from 239.252.0.0 to 239.255.255.255. When adding a device to the CMS (Client Management System) software, the multicast address must be the same as the device’s multicast IP. RTSP Port: The RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers.
ATM Digital Video Recorder User Manual Step 2 Input the correct user name and password, and click Login button to log in the device. Step 3 Enter the HTTPS settings interface. Configuration > Remote Configuration > Network Settings > HTTPS Step 4 Create the self-signed certificate or authorized certificate. Figure 10-18 HTTPS Settings OPTION 1: Create the self-signed certificate 1) Click the Create button to create the following dialog box.
ATM Digital Video Recorder User Manual Step 5 There will be the certificate information after you successfully create and install the certificate. Figure 10-20 Installed Certificate Property Step 6 Check the checkbox to enable the HTTPS function. Step 7 Click the Save button to save the settings. 10.2.7 Configuring Email Purpose The system can be configured to send an Email notification to all designated users if an event is detected, e.g. an alarm or motion event is detected, etc.
ATM Digital Video Recorder User Manual Step 3 Configure the following Email settings: Enable Server Authentication (optional): Check the checkbox to enable the server authentication feature. User Name: The user account of sender’s Email for SMTP server authentication. Password: The password of sender’s Email for SMTP server authentication. SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com). SMTP Port: The SMTP port. The default TCP/IP port used for SMTP is 25.
ATM Digital Video Recorder User Manual 10.3 Configuring Network Detection Purpose You can obtain network connecting status of DVR through the network detection function, including network delay, packet loss, etc. 10.3.1 Checking Network Traffic Purpose You can check the network traffic to obtain real-time information of DVR such as linking status, MTU, sending/receiving rate, etc. Step 1 Enter the Network Traffic interface.
ATM Digital Video Recorder User Manual Figure 10-24 Network Detection Interface Step 3 Select a NIC to test network delay and packet loss. Step 4 Enter the destination address in the text field of Destination Address. Step 5 Click the Test button to start testing network delay and packet loss. 10.3.3 Exporting Network Packet Purpose By connecting the DVR to network, the captured network data packet can be exported to USB-flash disk, SATA and other local backup devices.
ATM Digital Video Recorder User Manual Figure 10-26 Packet Export Attention Up to 1M data can be exported each time. 10.3.4 Checking Network Status Purpose You can also check the network status and quick set the network parameters in this interface. Step 1 Enter the Network Traffic interface. Menu > Maintenance > Net Detect Step 2 Click the Network Detection tab to enter the Network Detection interface. Step 3 Click Status on the right bottom of the interface.
ATM Digital Video Recorder User Manual Figure 10-29 Network Parameters Configuration 10.3.5 Checking Network Statistics Purpose: You can check the network statistics to obtain the real-time information of the device. Step 1 Enter the Network Statistics interface. Menu > Maintenance> Net Detect Step 2 Click the Network Stat. tab to enter the Network Statistics interface. Figure 10-30 Network Stat.
ATM Digital Video Recorder User Manual Chapter 11 ATM Settings 11.1 Network Interception Before you start Connect the device and the ATM (Automatic Teller Machine) to the network properly. Purpose The transaction information of ATM, including transaction card No, transaction amount, transaction behaviour, etc., can be captured by monitoring the data package of the network communication. Step 1 Enter the ATM Settings interface.
ATM Digital Video Recorder User Manual Figure 11-2 Network Interception Settings Step 6 Select the protocol for the network interception. 2 types of protocols are selectable: PSBC and Custom. If you select Custom as the protocol, click Setting to customize the protocol for network communication. For details, see Chapter 10.5 Custom Protocol Settings. Step 7 Click Apply and reboot the device to activate the new settings. 11.
ATM Digital Video Recorder User Manual Step 4 Select Serial Port Interception from the drop-down list as the input mode. Step 5 Configure the serial port interception settings. 1) Click Setting to enter the Serial Port Interception Settings interface. 2) Set the baud rate, data bit, stop bit, parity, flow ctrl and usage for the serial port communication. 3) Click OK to save the settings and exit.
ATM Digital Video Recorder User Manual Step 1 Enter the ATM Settings interface. Menu > Configuration > ATM Figure 11-5 ATM Settings-Network Protocol Step 2 Select the ATM from the drop-down list. Step 3 Check the checkbox of Enable ATM. Step 4 Select Network Protocol from the drop-down list as the input mode. Step 5 Configure the network protocol settings. 1) Click Setting to enter the Network Protocol Settings interface. 2) Set the Interception Port for the network communication.
ATM Digital Video Recorder User Manual 11.4 Serial Port Protocol Before you start Connect the device and the ATM (Automatic Teller Machine) via the serial port properly. Purpose The transaction information, including transaction card No, transaction amount, transaction behaviour, etc., will be sent from the ATM to the device. Step 1 Enter the ATM Settings interface. Menu > Configuration > ATM Figure 11-7 ATM Settings-Serial Port Protocol Step 2 Select the ATM from the drop-down list.
ATM Digital Video Recorder User Manual Figure 11-8 Serial Port Protocol Settings Step 6 Select the protocol from the drop-down list for the serial port communication. 2 types of protocols are selectable: HIKVISION and ICBC. Step 7 Click Apply and reboot the device to activate the new settings.
ATM Digital Video Recorder User Manual 11.5 Custom Protocol Settings Purpose When Network Interception or Serial Port Interception is selected as the input mode of the device, you can configure the custom protocols to analyze the data package captured via the network or serial port, thus to get the ATM transaction information. Step 1 Enter the ATM Settings interface. Menu > Configuration > ATM Step 2 Select Custom as the protocol. Step 3 Click Setting to enter the Custom Protocol Settings interface.
ATM Digital Video Recorder User Manual Figure 11-10 Custom Protocol Settings-Data Package Step 2 Select the Data Format and then set the Start Tag for the data package. Step 3 Select the Data Format and then set the End Tag for the data package. Step 4 (Optional) Check the checkbox of Enable Filter, select the Data Format, input the Content and set the Content Position to filter the specified contents. Step 5 Click Apply to save the new settings and click OK to exit.
ATM Digital Video Recorder User Manual Figure 11-11 Custom Protocol Settings-Transaction Information Step 2 Select the Major Type of transaction information from the drop-down list, including the Card No., Transaction Behaviour, Transaction Amount or Serial No. When the Transaction Behaviour is set as the major type, 8 minor types are selectable: Card In, Card Out, Overlay, Query, Withdrawal, Deposit, Change Password and Transfer.
ATM Digital Video Recorder User Manual Figure 11-13 Length Settings Select the Length Type to Variable, set the minimum length and maximum length for the transaction information, and then select data format and set the end character. Or select the Length Type to Fixed, and set the fixed length value. Or select the Length Type to Auto, set the length digits and length position, and then the length of the transaction information will be obtained from the message automatically.
ATM Digital Video Recorder User Manual Figure 11-14 Custom Protocol Settings-Trigger Channel Step 2 Check the checkboxes to select the analog channels or IP channels for the text overlay of transaction information and command triggered recording. Step 3 Check the check of Enable Time Delay. Step 4 Set the Delay Time value for menu display if there is no Card In or Card Out in the transaction information. The default delay time is 60s. The valid range of delay time is [0 ~ 65535].
ATM Digital Video Recorder User Manual Figure 11-15 Custom Protocol Settings-Overlay Position Step 2 If you do not need to overlay the transaction information on the display window, select None as the overlay position; If you need to overlay the transaction information on the display window, select Custom as the overlay position, and then drag the yellow rectangle to the desired position on the display window.
ATM Digital Video Recorder User Manual Chapter 12 RAID 12.1 Configuring Array Purpose RAID (redundant array of independent disks) is a storage technology that combines multiple disk drive components into a logical unit. A RAID setup stores data over multiple hard disk drives to provide enough redundancy so that data can be recovered if one disk fails. Data is distributed across the drives in one of several ways called "RAID levels", depending on what level of redundancy and performance is required.
ATM Digital Video Recorder User Manual Figure 12-1 RAID Working Flow 12.1.1 Enable RAID Purpose Perform the following steps to enable the RAID function, or the disk array cannot be created. OPTION 1: Enable the RAID function in the Wizard when the device startup, please refer to step 4 of Chapter 2.4.2. OPTION 2: Enable the RAID function in the HDD Management Interface. Step 1 Enter the Disk Mode configuration interface.
ATM Digital Video Recorder User Manual 12.1.2 One-touch Configuration Purpose Through one-touch configuration, you can quickly create the disk array. By default, the array type to be created is RAID 5. Before you start 1. The RAID function should be enabled, please refer to the Chapter 12.1.1 for details. 2. As the default array type is RAID 5, please install at least 3 HDDs in you device. Step 1 Enter the RAID configuration interface.
ATM Digital Video Recorder User Manual If you install 4 HDDs for one-touch configuration, a hot spare disk will be set by default. It is recommended to set hot spare disk for automatically rebuilding the array when the array is abnormal. Step 5 When the array configuration is completed, click OK button in the pop-up message box to finish the settings. Step 6 You can click Array tab to view the information of the successfully created array.
ATM Digital Video Recorder User Manual Figure 12-7 Physical Disk Settings Interface Step 2 Click Creat button to enter the Create Array interface. Figure 12-8 Create Array Interface Step 3 Edit the Array Name; set the RAID Level to RAID 0, RAID 1, RAID 5, or RAID 10; select the Physical Disk that you want to configure array. If you choose RAID 0, at least 2 HDDs must be installed. If you choose RAID 1, 2 HDDs need to be configured for RAID 1.
ATM Digital Video Recorder User Manual Figure 12-9 Error Message Box Step 5 You can click Array tab to view the successfully created array. Figure 12-10 Array Settings Interface 12.2 Rebuilding Array Purpose The working status of array includes Functional, Degraded and Offline. By viewing the array status, you can take immediate and proper maintenance for the disks so as to ensure the high security and reliability of the data stored in the disk array.
ATM Digital Video Recorder User Manual Figure 12-11 Physical Disk Settings Interface Step 2 Select a disk and click to set it as the hot spare disk. Only global hot spare mode is supported. 12.2.1 Automatically Rebuilding Array Purpose When the virtual disk is in Degraded status, the device can start rebuilding the array automatically with the hot spare disk to ensure the high security and reliability of the data. Step 1 Enter the Array Settings interface. The status of the array is Degraded.
ATM Digital Video Recorder User Manual Step 1 Enter the Array Settings interface. The disk 3 is lost. Menu > HDD > RAID > Array Figure 12-13 Array Settings Interface Step 2 Click Array tab to return to the Array Settings interface and click rebuild. to configure the array At least one available physical disk should exist for rebuilding the array. Figure 12-14 Rebuild Array Interface Step 3 Select the available physical disk and click OK button to confirm to rebuild the array.
ATM Digital Video Recorder User Manual Figure 12-15 Array Settings Interface Step 2 Select an array and click to delete the array. Figure 12-16 Confirm Array Deletion Step 3 In the pop-up message box, click Yes button to confirm the array deletion. Deleting array will cause to delete all the data in the array. 12.4 Checking and Editing Firmware Purpose You can view the information of the firmware and set the background task speed on the Firmware interface.
ATM Digital Video Recorder User Manual Chapter 13 HDD Management 13.1 Initializing HDDs Purpose A newly installed hard disk drive (HDD) must be initialized before it can be used with your DVR. Step 1 Enter the HDD Information interface. Menu > HDD > General Figure 13-1 HDD Information Interface You can view the Total Capacity, Free Space and Remaining Recording Time of the HDD.
ATM Digital Video Recorder User Manual Figure 13-3 Start Initialization Step 5 After the HDD has been initialized, the status of the HDD will change from Uninitialized to Normal. Figure 13-4 HDD Status Changes to Normal Initializing the HDD will erase all data on it. The HDDs which are free of working for a long time can be enabled to sleep, thus to decrease the power consumption of the device and extend the life of the HDDs.
ATM Digital Video Recorder User Manual Figure 13-6 HDD Information Interface Step 2 Click the Add button to enter the Add NetHDD interface, as shown in Figure 13-7. Figure 13-7 HDD Information Interface Step 3 Add the allocated NetHDD. Step 4 Select the type to NAS or IP SAN. Step 5 Configure the NAS or IP SAN settings. Add NAS disk: 1) Enter the NetHDD IP address in the text field. 2) Click Search to search the available NAS disks. 3) Select the NAS disk from the list shown below.
ATM Digital Video Recorder User Manual Figure 13-8 Add NAS Disk Add IP SAN: 1) Enter the NetHDD IP address in the text field. 2) Click the Search button to the available IP SAN disks. 3) Select the IP SAN disk from the list shown below. 4) Click the OK button to add the selected IP SAN disk. Up to 8 IP SAN disks can be added. Figure 13-9 Add IP SAN Disk 5) After having successfully added the NAS or IP SAN disk, return to the HDD Information menu. The added NetHDD will be displayed in the list.
ATM Digital Video Recorder User Manual Figure 13-10 Initialize Added NetHDD 13.3 Managing HDD Group 13.3.1 Setting HDD Groups Purpose Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD group through HDD settings. Step 1 Enter the Storage Mode interface. Menu > HDD > Advanced Step 2 Set the Mode to Group, as shown in Figure 13-11. Figure 13-11 Storage Mode Interface Step 3 Click the Apply button and the following Attention box will pop up.
ATM Digital Video Recorder User Manual Figure 13-13 Local HDD Settings Interface Step 7 Select the Group number for the current HDD. The default group No. for each HDD is 1. Step 8 Click the OK button to confirm the settings. Figure 13-14 Confirm HDD Group Settings Step 9 In the pop-up Attention box, click the Yes button to finish the settings. 13.3.2 Setting HDD Property Purpose The HDD property can be set to redundancy, read-only or read/write (R/W).
ATM Digital Video Recorder User Manual Figure 13-15 Set HDD Property Step 3 Set the HDD property to R/W, Read-only or Redundancy. Step 4 Click the OK button to save the settings and exit the interface. Step 5 In the HDD Information menu, the HDD property will be displayed in the list. At least 2 hard disks must be added on your DVR when you want to set a HDD to Redundancy, and there is one HDD with R/W property. 13.
ATM Digital Video Recorder User Manual Figure 13-16 Storage Mode Settings Interface Step 4 Select a camera for which you want to configure quota. Step 5 Enter the storage capacity in the text field of Max. Record Capacity (GB). Step 6 You can copy the quota settings of the current camera to other cameras if required. Click the Copy button to enter the Copy Camera interface, as shown in Figure 13-17.
ATM Digital Video Recorder User Manual You may check the status of the installed HDDs on DVR so as to take immediate check and maintenance in case of HDD failure. Checking HDD Status in HDD Information Interface Step 1 Enter the HDD Information interface. Menu > HDD > General Step 2 Check the status of each HDD which is displayed on the list, as shown in Figure 13-18. Figure 13-18 View HDD Status (1) If the status of HDD is Normal or Sleeping, it works normally.
ATM Digital Video Recorder User Manual If you want to use the HDD even when the S.M.A.R.T. checking is failed, you can check the checkbox before the Continue to use this disk when self-evaluation is failed item. Figure 13-20 S.M.A.R.T Settings Interface 13.7 Detecting Bad Sector Purpose You can detect the bad sector of the HDD to check the status of the HDD. Step 1 Enter the HDD Detect interface. Menu>HDD>HDD Detect Step 2 Click the Bad Sector Detection tab to enter the interface.
ATM Digital Video Recorder User Manual Step 4 You can click the Pause button to pause the detection and click the Resume button to resume the detection. Step 5 If there is error information about the HDD, you can click the Error Info button to view the information. 13.8 Configuring HDD Error Alarms Purpose You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal. Step 1 Enter the Exception interface.
ATM Digital Video Recorder User Manual Chapter 14 Camera Settings 14.1 Configuring OSD Settings Purpose You can configure the OSD (On-Screen Display) settings for the camera, including date/time, camera name, etc. Step 1 Enter the OSD Configuration interface. Menu > Camera > OSD Step 2 Select the camera to configure OSD settings. Step 3 Edit the Camera Name in the text field. Step 4 Configure the Display Name, Display Date and Display Week by checking the checkbox.
ATM Digital Video Recorder User Manual Figure 14-2 Copy Settings to Other Cameras 2) Select the camera (s) to be configured with the same OSD settings. You can also check the checkbox of Analog to select all cameras. 3) Click the OK button to finish the Copy settings and back to the OSD Configuration interface. Step 8 Click Apply to save the settings. 14.2 Configuring Privacy Mask Purpose You are allowed to configure the four-sided privacy mask zones that cannot be viewed or recorded by the operator.
ATM Digital Video Recorder User Manual Figure 14-3 Set Privacy Mask Area Step 6 You can click the Copy button to copy the privacy mask settings of the current camera to other cameras. Please refer to step 7 of Chapter 14.1 Configuring OSD Settings. Step 7 Click Apply to save the settings. 14.3 Configuring Video Parameters 14.3.1 Configuring Image Settings Step 1 Enter the Image Settings interface. Menu > Camera > Image Step 2 Select the Image Settings tab.
ATM Digital Video Recorder User Manual Figure 14-5 Image Settings Interface (IP Camera) Step 3 Select the camera to set image parameters. Step 4 Two periods for different image settings are provided, select the period name in the drop-down list. The time periods cannot be overlapped with each other. Step 5 Select the mode from the drop-down list of Mode. There are four modes selectable for the analog cameras: Standard, Indoor, Dim Light and Outdoor.
ATM Digital Video Recorder User Manual Figure 14-6 Camera Parameters Settings Step 3 Select the Camera from the drop-down list. Step 4 (Optional) Adjust the parameters including Day to Night Sensitivity, Night to Day Sensitivity and IR Light Brightness for the analog cameras. You can also click Default to set the parameters to the default settings. Step 5 (Optional) Click Copy to copy the parameters of the current camera to other analog cameras. Step 6 Click Apply to save the settings.
ATM Digital Video Recorder User Manual Chapter 15 DVR Management and Maintenance 15.1 Viewing System Information Step 1 Enter the System Information interface. Menu > Maintenance > System Info Step 2 You can click the Device Info, Camera, Record, Alarm, Network and HDD tabs to view the system information of the device. Figure 15-1 System Information Interface 15.
ATM Digital Video Recorder User Manual Figure 15-2 Log Search Interface Step 2 Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and Minor Type. Step 3 Click the Search button to start search log files. Step 4 The matched log files will be displayed on the list shown below. Up to 2000 log files can be displayed each time. Figure 15-3 Log Search Results Step 5 You can click the button of each log or double-click it to view its detailed information.
ATM Digital Video Recorder User Manual Figure 15-4 Log Information Interface Step 6 If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure 15-5. Figure 15-5 Export Log Files Step 7 Select the backup device from the drop-down list of Device Name. Step 8 Click the Export to export the log files to the selected backup device.
ATM Digital Video Recorder User Manual 15.3 Importing/Exporting IP Camera Info Purpose The information of added IP camera can be generated into an excel file and exported to the local device for backup, including the IP address, manage port, password of admin, etc. And the exported file can be edited on your PC, like adding or deleting the content, and copy the setting to other devices by importing the excel file to it. Step 1 Enter the camera management interface.
ATM Digital Video Recorder User Manual Step 2 Click the Export button to export configuration files to the selected local backup device. Step 3 To import a configuration file, select the file from the selected backup device and click the Import button. After the import process is completed, you must reboot the DVR. After having finished the import of configuration files, the device will reboot automatically. 15.
ATM Digital Video Recorder User Manual Figure 15-8 FTP Upgrade Interface Step 3 Enter the FTP Server Address in the text field. Step 4 Click the Upgrade button to start upgrading. Step 5 After the upgrading is completed, reboot the DVR to activate the new firmware. 15.6 Upgrading Camera Purpose You can upgrade multiple connected analog cameras supporting HDTVI signal simultaneously with DVR. Step 1 Enter the Camera Upgrade interface.
ATM Digital Video Recorder User Manual Figure 15-10 Restore Defaults Step 2 Select the restoring type from the following three options. Restore Defaults: Restore all parameters, except the network (including IP address, subnet mask, gateway, MTU, NIC working mode, default route, server port, etc.) and user account parameters, to the factory default settings. Factory Defaults: Restore all parameters to the factory default settings. Restore to Inactive: Restore the device to the inactive status.
ATM Digital Video Recorder User Manual Chapter 16 Others 16.1 Configuring General Settings Purpose You can configure the output resolution, system time, mouse pointer speed, etc. Step 1 Enter the General Settings interface. Menu > Configuration > General Step 2 Select the General tab. Figure 16-1 General Settings Interface Step 3 Configure the following settings: Language: The default language used is English. Output Standard: Select the output standard to be PAL or NTSC.
ATM Digital Video Recorder User Manual HDMI and VGA share simultaneous output. The LCD does not share simultaneous output with HDMI/VGA output. The LCD resolution stays as 1024 × 600. The default VGA/HDMI resolution is 1024 × 768/60Hz. If you connect the external display to the DVR via the HDMI or VGA interface, set the VGA/HDMI resolution between 1280 × 720/60Hz to 1920 × 1080/60Hz, and click Apply. The attention box will pop up as shown below.
ATM Digital Video Recorder User Manual Menu >Configuration> RS-232 Figure 16-3 RS-232 Settings Interface Step 2 Configure RS-232 parameters, including baud rate, data bit, stop bit, parity, flow control and usage. Step 3 Click Apply to save the settings. 16.3 Configuring DST Settings Step 1 Enter the General Settings interface. Menu >Configuration>General Step 2 Choose DST Settings tab. Figure 16-4 DST Settings Interface You can check the checkbox before the Auto DST Adjustment item.
ATM Digital Video Recorder User Manual Figure 16-5 More Settings Interface Step 3 Configure the following settings: Device Name: Edit the name of DVR. Device No.: Edit the serial number of DVR. The Device No. can be set in the range of 1 to 255, and the default No. is 255. Auto Logout: Set timeout time for menu inactivity. E.g., when the timeout time is set to 5 Minutes, then the system will exit from the current operation menu to live view screen after 5 minutes of menu inactivity.
ATM Digital Video Recorder User Manual Figure 16-6 User Management Interface Step 2 Click Add to enter the Add User interface. Figure 16-7 Add User Menu Step 3 Enter the information for new user, including User Name, Password, Confirm, Level and User’s MAC Address. Password: Set the password for the user account.
ATM Digital Video Recorder User Manual Guest: The Guest user has no permission of Two-way Audio in Remote Configuration and only has the local/remote playback in the Camera Configuration by default. User’s MAC Address: The MAC address of the remote PC which logs onto the DVR. If it is configured and enabled, it only allows the remote user with this MAC address to access the DVR. Step 4 Click the OK button to save the settings and go back to the User Management interface.
ATM Digital Video Recorder User Manual Local Camera Management: Enabling and disabling analog camera (s). Adding, deleting and editing of network camera (s). This function is supported by HDVR series. Local Advanced Operation: Operating HDD management (initializing HDD, setting HDD property), upgrading system firmware. Local Shutdown /Reboot: Shutting down or rebooting the device. Remote Configuration Remote Log Search: Remotely viewing logs that are saved on the device.
ATM Digital Video Recorder User Manual 3) Click OK to save the settings and exit. 16.5.2 Deleting a User Step 1 Enter the User Management interface. Menu >Configuration>User Step 2 Select the user to be deleted from the list, as shown in Figure 16-10. Figure 16-10 User List Step 3 Click to delete the selected user account. 16.5.3 Editing a User Purpose For the added user accounts, you can edit the parameters. Step 1 Enter the User Management interface.
ATM Digital Video Recorder User Manual Figure 16-11 Edit User Interface Step 4 Edit the corresponding parameters. Operator and Guest You can edit the user information, including user name, password, permission level and MAC address. Check the checkbox of Change Password if you want to change the password, and input the new password in the text field of Password and Confirm. A strong password is recommended. Admin You are only allowed to edit the password and MAC address.
ATM Digital Video Recorder User Manual 2) Use the mouse to draw a pattern among the 9 dots on the screen. Release the mouse when the pattern is done. 3) Confirm the pattern again with the mouse. Please refer to Chapter 2.3.1 Configuring the Unlock Pattern for detailed instructions. Figure 16-12 Set Unlock Patter for Admin User Step 6 (Optional) Click icon after Draw Unlock Pattern to modify the pattern. Step 7 (Optional) Click icon after Export GUID to pop up the Reset Password interface.
ATM Digital Video Recorder User Manual Chapter 17 Appendix 17.1 Glossary • Dual-Stream: Dual-stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 1080P and the sub-stream having a maximum resolution of CIF. • DVR: Acronym for Digital Video Recorder.
ATM Digital Video Recorder User Manual • PTZ: Acronym for Pan, Tilt, Zoom. PTZ cameras are motor driven systems that allow the camera to pan left and right, tilt up and down and zoom in and out. • USB: Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices to a host computer. 17.2 Troubleshooting No image displayed on the monitor after the device is starting up normally. Possible Reasons: — No VGA or HDMI connections. — Connection cable is damaged.
ATM Digital Video Recorder User Manual Step 2 Verify the HDD is initialized. 1) Select “Menu>HDD>General”. 2) If the status of the HDD is “Uninitialized”, please check the checkbox of corresponding HDD and click the “Init” button. Step 3 Verify the HDD is detected or is in good condition. 1) Select “Menu>HDD>General”. 2) If the HDD is not detected or the status is “Abnormal”, please replace the dedicated HDD according to the requirement. Step 4 Check if the fault is solved by the step 1 to step 3.
ATM Digital Video Recorder User Manual If not, please contact the engineer from our company to do the further process. The image gets stuck when DVR is playing back by single or multi-channel cameras. Possible Reasons: — The frame rate is not the real-time frame rate. — The DVR supports up to 16-channel synchronize playback at the resolution of 4CIF, if you want a 16-channel synchronize playback at the resolution of 720p, the frame extracting may occur, which leads to a slight stuck.
ATM Digital Video Recorder User Manual 17.3 Summary of Chnages 17.3.1 Version 3.4.83 Upgraded: iDS-8104AHQXLI-E4 supports up to 4-ch smart ATM configuration of panel mode, environment mode, human face mode, and safety cabin mode together; up to 2-ch human face mode, up to 2-ch safety cabin, or up to 1-ch human face mode and 1-ch safety cabin mode together. Panel mode and environment mode can be enabled for all the cameras respectively. Advanced parameters upgrade of smart ATM protection system.
ATM Digital Video Recorder User Manual Clear-text password available. GUID file can be exported for password resetting. Multiple connected analog cameras supporting HDTVI signal can be upgraded simultaneously via DVR. Configurable output bandwidth limit. If DHCP is enabled, you can enable DNS DHCP or disable it and configure the Preferred DNS Server and Alternate DNS Server.
ATM Digital Video Recorder User Manual 223
