User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable the H.265 Stream Access
- 4.1.3 ANR
- 4.1.4 Manual Recording
- 4.1.5 Configure Plan Recording
- 4.1.6 Configure Continuous Recording
- 4.1.7 Configure Motion Detection Triggered Recording
- 4.1.8 Configure Event Triggered Recording
- 4.1.9 Configure Alarm Triggered Recording
- 4.1.10 Configure Picture Capture
- 4.1.11 Configure Holiday Recording
- 4.1.12 Configure Redundant Recording and Capture
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Event
- 5.1 Normal Event Alarm
- 5.2 VCA Event Alarm
- 5.2.1 Temperature Screening
- 5.2.2 Loitering Detection
- 5.2.3 People Gathering Detection
- 5.2.4 Fast Moving Detection
- 5.2.5 Parking Detection
- 5.2.6 Unattended Baggage Detection
- 5.2.7 Object Removal Detection
- 5.2.8 Audio Exception Detection
- 5.2.9 Defocus Detection
- 5.2.10 Sudden Scene Change Detection
- 5.2.11 PIR Alarm
- 5.2.12 Thermal Camera Detection
- 5.2.13 Configure Queue Management
- 5.3 Configure Arming Schedule
- 5.4 Configure Linkage Actions
- Chapter 6 Smart Analysis
- 6.1 Engine Configuration
- 6.2 Task Configuration
- 6.3 Face Picture Comparison
- 6.4 Perimeter Protection
- 6.5 Human Body Detection
- 6.6 Multi-Target-Type Detection
- 6.7 Vehicle Detection
- 6.8 Target Detection
- 6.9 People Counting
- 6.10 Heat Map
- Chapter 7 File Management
- Chapter 8 Storage
- Chapter 9 POS Configuration
- Chapter 10 Hot Spare Recorder Backup
- Chapter 11 Network Settings
- Chapter 12 User Management and Security
- Chapter 13 System Management
- Chapter 14 Appendix
- 14.1 Glossary
- 14.2 Communication Matrix
- 14.3 Device Command
- 14.4 Frequently Asked Questions
- 14.4.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen of live view?
- 14.4.2 Why is the video recorder notifying not support the stream type?
- 14.4.3 Why is the video recorder notifying risky password after adding network camera?
- 14.4.4 How to improve the playback image quality?
- 14.4.5 How to confirm the video recorder is using H.265 to record video?
- 14.4.6 Why is the timeline at playback not constant?
- 14.4.7 When adding network camera, the video recorder notifies network is unreachable.
- 14.4.8 Why is the IP address of network camera being changed automatically?
- 14.4.9 Why is the video recorder notifying IP conflict?
- 14.4.10 Why is image getting stuck when the video recorder is playing back by single or multi-channel cameras?
- 14.4.11 Why does my video recorder make a beeping sound after booting?
- 14.4.12 Why is there no recorded video after setting the motion detection?
- 14.4.13 Why is the sound quality not good in recording video?
Network Video Recorder User Manual
109
Use the eSATA for record/capture. Refer to the following steps for operating instructions.
Figure 8-4 eSATA Mode
What to do next
If eSATA usage is set as Record/Capture, enter the storage device interface to edit its property or
initialize it.
Configure eSATA for Auto Backup
If you made an automatic backup plan, the video recorder will back up the local videos of 24 hours
ahead of the backup start time to eSATA.
Before You Start
Ensure the device has correctly connected with an external eSATA hard drive, and its usage type is
set as Export. Refer to Manage eSATA for details.
Steps
1. Go to Storage → Auto Backup.
2. Check Auto Backup.
3. Set the backup start time in Start Backup at.
Note
If the day experiences a failed backup, the video recorder will back up the videos 48 hours
ahead of the backup start time in the next day.
4. Select channels for backup.
5. Select Backup Stream Type as your desire.
6. Select Overwrite type.
– Disable: When HDD is full, it will stop writing.
– Enable: When HDD is full, it will continue to write new files by deleting the oldest files.
7. Click Apply.