User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable the H.265 Stream Access
- 4.1.3 ANR
- 4.1.4 Manual Recording
- 4.1.5 Configure Plan Recording
- 4.1.6 Configure Continuous Recording
- 4.1.7 Configure Motion Detection Triggered Recording
- 4.1.8 Configure Event Triggered Recording
- 4.1.9 Configure Alarm Triggered Recording
- 4.1.10 Configure Picture Capture
- 4.1.11 Configure Holiday Recording
- 4.1.12 Configure Redundant Recording and Capture
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Event
- 5.1 Normal Event Alarm
- 5.2 VCA Event Alarm
- 5.2.1 Temperature Screening
- 5.2.2 Loitering Detection
- 5.2.3 People Gathering Detection
- 5.2.4 Fast Moving Detection
- 5.2.5 Parking Detection
- 5.2.6 Unattended Baggage Detection
- 5.2.7 Object Removal Detection
- 5.2.8 Audio Exception Detection
- 5.2.9 Defocus Detection
- 5.2.10 Sudden Scene Change Detection
- 5.2.11 PIR Alarm
- 5.2.12 Thermal Camera Detection
- 5.2.13 Configure Queue Management
- 5.3 Configure Arming Schedule
- 5.4 Configure Linkage Actions
- Chapter 6 Smart Analysis
- 6.1 Engine Configuration
- 6.2 Task Configuration
- 6.3 Face Picture Comparison
- 6.4 Perimeter Protection
- 6.5 Human Body Detection
- 6.6 Multi-Target-Type Detection
- 6.7 Vehicle Detection
- 6.8 Target Detection
- 6.9 People Counting
- 6.10 Heat Map
- Chapter 7 File Management
- Chapter 8 Storage
- Chapter 9 POS Configuration
- Chapter 10 Hot Spare Recorder Backup
- Chapter 11 Network Settings
- Chapter 12 User Management and Security
- Chapter 13 System Management
- Chapter 14 Appendix
- 14.1 Glossary
- 14.2 Communication Matrix
- 14.3 Device Command
- 14.4 Frequently Asked Questions
- 14.4.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen of live view?
- 14.4.2 Why is the video recorder notifying not support the stream type?
- 14.4.3 Why is the video recorder notifying risky password after adding network camera?
- 14.4.4 How to improve the playback image quality?
- 14.4.5 How to confirm the video recorder is using H.265 to record video?
- 14.4.6 Why is the timeline at playback not constant?
- 14.4.7 When adding network camera, the video recorder notifies network is unreachable.
- 14.4.8 Why is the IP address of network camera being changed automatically?
- 14.4.9 Why is the video recorder notifying IP conflict?
- 14.4.10 Why is image getting stuck when the video recorder is playing back by single or multi-channel cameras?
- 14.4.11 Why does my video recorder make a beeping sound after booting?
- 14.4.12 Why is there no recorded video after setting the motion detection?
- 14.4.13 Why is the sound quality not good in recording video?
Network Video Recorder User Manual
126
4. Enter the virtual server setting page of router; fill in the blank of Internal Source Port with the
internal port value, the blank of External Source Port with the external port value, and other
required contents.
Note
● Each item should be corresponding with the device port, including server port, http port,
RTSP port and https port.
● The virtual server setting interface below is for reference only, it may be different due to
different router manufactures. Please contact the manufacture of router if you have any
problems with setting virtual server.
Figure 11-3 Setting Virtual Server Item
11.4 Configure SNMP
You can configure SNMP settings to get device status and parameter information.
Before You Start
Download the SNMP software to receive device information via the SNMP port. By setting the trap
address and port, the device is allowed to send alarm events and exception messages to the
surveillance center.
Steps
1. Go to System → Network → Advanced → SNMP.