User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable H.265 Stream Access
- 4.1.3 Manual Recording
- 4.1.4 Configure Recording Schedule
- 4.1.5 Configure Continuous Recording
- 4.1.6 Configure Motion Detection Triggered Recording
- 4.1.7 Configure Event Triggered Recording
- 4.1.8 Configure Alarm Triggered Recording
- 4.1.9 Configure Picture Capture
- 4.1.10 Configure Holiday Recording
- 4.1.11 Configure Redundant Recording and Capture
- 4.1.12 Configure 1080p Lite Mode
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Smart Analysis
- 5.1 Engine Configuration
- 5.2 Task Configuration
- 5.3 Configure Enhanced VCA Mode
- 5.4 Face Picture Comparison
- 5.5 Perimeter Protection
- 5.6 Human Body Detection
- 5.7 Motion Detection
- 5.8 Vehicle Detection
- 5.9 Target Detection
- 5.10 View People Counting Statistics
- 5.11 Heat Map
- Chapter 6 Event
- Chapter 7 File Management
- Chapter 8 POS Configuration
- Chapter 9 Storage
- Chapter 10 Network Settings
- Chapter 11 User Management and Security
- Chapter 12 System Management
- Chapter 13 Appendix
- 13.1 List of Applicable Power Adapter
- 13.2 Glossary
- 13.3 Communication Matrix
- 13.4 Device Command
- 13.5 Frequently Asked Questions
- 13.5.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen live view?
- 13.5.2 Why is the video recorder notifying risky password after a network camera is added?
- 13.5.3 Why is the video recorder notifying the stream type is not supported?
- 13.5.4 How to improve the playback image quality?
- 13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view?
- 13.5.6 How to confirm the video recorder is using H.265 to record video?
- 13.5.7 Why is the timeline at playback not constant?
- 13.5.8 Why is the video recorder notifying the network is unreachable when a network camera is being added?
- 13.5.9 Why is the IP address of network camera being changed automatically?
- 13.5.10 Why is the video recorder notifying IP conflict?
- 13.5.11 Why is image getting stuck when playing back by single or multi-channel cameras?
- 13.5.12 Why does my video recorder make a beeping sound after booting?
- 13.5.13 Why is there no recorded video after the motion detection is set?
- 13.5.14 Why is the device not able to control PTZ camera via coaxitron?
- 13.5.15 Why does the PTZ seem unresponsive via RS-485?
- 13.5.16 Why is the video sound quality not good?
Digital Video Recorder User Manual
62
1) Click Edit.
2) Optional: Check Enable of Display Status and Notify Surveillance Center.
3) Set Start Time of video to analyze.
4) Click OK.
4. Check cameras and click Enabled to start analyzing.
Task status includes 3 conditions: Disabled, Waiting, and Enabled.
● Disabled: No analysis task is enabled on the camera.
● Waiting: The analysis task of the camera is enabled. Device is waiting to analyze data.
● Enabled: The analysis task of the camera is enabled and device is analyzing data of the
camera.
5. Optional: For Non-Real-Time Face Picture Comparison analysis mode, click View Record to view
the progress of each day.
5.3 Configure Enhanced VCA Mode
Enabling enhanced VCA mode will maximize the connectable channel number for line crossing
detection and intrusion detection. However, it will disable 2K/4K HDMI output resolution and 4
MP/5 MP/8 MP signal input for HUHI-K series. And for HQHI-K series, it will disable CVBS output
and channel-zero encoding.
Go to System → General, and check Enhanced VCA Mode.
5.4 Face Picture Comparison
The device supports the face picture comparison alarm and face capture for the connected camera
based on face recognition feature.
Go to Smart Analysis → Smart Analysis → Engine Configuration. Configure at least one engine
usage as Facial Recognition. Refer to Engine Configuration for details.
Note
The chapter is only available for certain models of iDS series.
5.4.1 Facial Detection
The facial detection detects the face appearing in the surveillance scene. Linkage actions can be
triggered when a human face is detected.
Steps
1. Go to System → Event → Smart Event.
2. Click Face Detection.