User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable H.265 Stream Access
- 4.1.3 Manual Recording
- 4.1.4 Configure Recording Schedule
- 4.1.5 Configure Continuous Recording
- 4.1.6 Configure Motion Detection Triggered Recording
- 4.1.7 Configure Event Triggered Recording
- 4.1.8 Configure Alarm Triggered Recording
- 4.1.9 Configure Picture Capture
- 4.1.10 Configure Holiday Recording
- 4.1.11 Configure Redundant Recording and Capture
- 4.1.12 Configure 1080p Lite Mode
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Smart Analysis
- 5.1 Engine Configuration
- 5.2 Task Configuration
- 5.3 Configure Enhanced VCA Mode
- 5.4 Face Picture Comparison
- 5.5 Perimeter Protection
- 5.6 Human Body Detection
- 5.7 Motion Detection
- 5.8 Vehicle Detection
- 5.9 Target Detection
- 5.10 View People Counting Statistics
- 5.11 Heat Map
- Chapter 6 Event
- Chapter 7 File Management
- Chapter 8 POS Configuration
- Chapter 9 Storage
- Chapter 10 Network Settings
- Chapter 11 User Management and Security
- Chapter 12 System Management
- Chapter 13 Appendix
- 13.1 List of Applicable Power Adapter
- 13.2 Glossary
- 13.3 Communication Matrix
- 13.4 Device Command
- 13.5 Frequently Asked Questions
- 13.5.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen live view?
- 13.5.2 Why is the video recorder notifying risky password after a network camera is added?
- 13.5.3 Why is the video recorder notifying the stream type is not supported?
- 13.5.4 How to improve the playback image quality?
- 13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view?
- 13.5.6 How to confirm the video recorder is using H.265 to record video?
- 13.5.7 Why is the timeline at playback not constant?
- 13.5.8 Why is the video recorder notifying the network is unreachable when a network camera is being added?
- 13.5.9 Why is the IP address of network camera being changed automatically?
- 13.5.10 Why is the video recorder notifying IP conflict?
- 13.5.11 Why is image getting stuck when playing back by single or multi-channel cameras?
- 13.5.12 Why does my video recorder make a beeping sound after booting?
- 13.5.13 Why is there no recorded video after the motion detection is set?
- 13.5.14 Why is the device not able to control PTZ camera via coaxitron?
- 13.5.15 Why does the PTZ seem unresponsive via RS-485?
- 13.5.16 Why is the video sound quality not good?
Digital Video Recorder User Manual
xix
13.5 Frequently Asked Questions ........................................................................................... 158
13.5.1 Why is there a part of channels displaying “No Resource” or turning black
screen in multi-screen live view? ............................................................................ 158
13.5.2 Why is the video recorder notifying risky password after a network camera is
added? ..................................................................................................................... 158
13.5.3 Why is the video recorder notifying the stream type is not supported?........... 159
13.5.4 How to improve the playback image quality? .................................................... 159
13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view? ................... 159
13.5.6 How to confirm the video recorder is using H.265 to record video? ................. 160
13.5.7 Why is the timeline at playback not constant? ................................................... 160
13.5.8 Why is the video recorder notifying the network is unreachable when a network
camera is being added? ........................................................................................... 160
13.5.9 Why is the IP address of network camera being changed automatically? ........ 161
13.5.10 Why is the video recorder notifying IP conflict? ............................................... 161
13.5.11 Why is image getting stuck when playing back by single or multi-channel
cameras? .................................................................................................................. 161
13.5.12 Why does my video recorder make a beeping sound after booting? .............. 161
13.5.13 Why is there no recorded video after the motion detection is set? ................ 162
13.5.14 Why is the device not able to control PTZ camera via coaxitron? ................... 162
13.5.15 Why does the PTZ seem unresponsive via RS-485? .......................................... 162
13.5.16 Why is the video sound quality not good? ........................................................ 163