User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable H.265 Stream Access
- 4.1.3 Manual Recording
- 4.1.4 Configure Recording Schedule
- 4.1.5 Configure Continuous Recording
- 4.1.6 Configure Motion Detection Triggered Recording
- 4.1.7 Configure Event Triggered Recording
- 4.1.8 Configure Alarm Triggered Recording
- 4.1.9 Configure Picture Capture
- 4.1.10 Configure Holiday Recording
- 4.1.11 Configure Redundant Recording and Capture
- 4.1.12 Configure 1080p Lite Mode
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Smart Analysis
- 5.1 Engine Configuration
- 5.2 Task Configuration
- 5.3 Configure Enhanced VCA Mode
- 5.4 Face Picture Comparison
- 5.5 Perimeter Protection
- 5.6 Human Body Detection
- 5.7 Motion Detection
- 5.8 Vehicle Detection
- 5.9 Target Detection
- 5.10 View People Counting Statistics
- 5.11 Heat Map
- Chapter 6 Event
- Chapter 7 File Management
- Chapter 8 POS Configuration
- Chapter 9 Storage
- Chapter 10 Network Settings
- Chapter 11 User Management and Security
- Chapter 12 System Management
- Chapter 13 Appendix
- 13.1 List of Applicable Power Adapter
- 13.2 Glossary
- 13.3 Communication Matrix
- 13.4 Device Command
- 13.5 Frequently Asked Questions
- 13.5.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen live view?
- 13.5.2 Why is the video recorder notifying risky password after a network camera is added?
- 13.5.3 Why is the video recorder notifying the stream type is not supported?
- 13.5.4 How to improve the playback image quality?
- 13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view?
- 13.5.6 How to confirm the video recorder is using H.265 to record video?
- 13.5.7 Why is the timeline at playback not constant?
- 13.5.8 Why is the video recorder notifying the network is unreachable when a network camera is being added?
- 13.5.9 Why is the IP address of network camera being changed automatically?
- 13.5.10 Why is the video recorder notifying IP conflict?
- 13.5.11 Why is image getting stuck when playing back by single or multi-channel cameras?
- 13.5.12 Why does my video recorder make a beeping sound after booting?
- 13.5.13 Why is there no recorded video after the motion detection is set?
- 13.5.14 Why is the device not able to control PTZ camera via coaxitron?
- 13.5.15 Why does the PTZ seem unresponsive via RS-485?
- 13.5.16 Why is the video sound quality not good?
Digital Video Recorder User Manual
157
Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of
computers over a network.
NTSC
Acronym for National Television System Committee. NTSC is an analog television standard used
in such countries as the United States and Japan. Each frame of an NTSC signal contains 525
scan lines at 60Hz.
NVR
Acronym for Network Video Recorder. An NVR can be a PC-based or embedded system used for
centralized management and storage for IP cameras, IP Domes and other DVRs.
PAL
Acronym for Phase Alternating Line. PAL is also another video standard used in broadcast
televisions systems in large parts of the world. PAL signal contains 625 scan lines at 50Hz.
PTZ
Acronym for Pan, Tilt, Zoom. PTZ cameras are motor driven systems that allow the camera to
pan left and right, tilt up and down and zoom in and out.
USB
Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices
to a host computer.
13.3 Communication Matrix
Please scan the QR code below to view the communication matrix document.
Figure 13-1 Communication Matrix