User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable H.265 Stream Access
- 4.1.3 Manual Recording
- 4.1.4 Configure Recording Schedule
- 4.1.5 Configure Continuous Recording
- 4.1.6 Configure Motion Detection Triggered Recording
- 4.1.7 Configure Event Triggered Recording
- 4.1.8 Configure Alarm Triggered Recording
- 4.1.9 Configure Picture Capture
- 4.1.10 Configure Holiday Recording
- 4.1.11 Configure Redundant Recording and Capture
- 4.1.12 Configure 1080p Lite Mode
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Smart Analysis
- 5.1 Engine Configuration
- 5.2 Task Configuration
- 5.3 Configure Enhanced VCA Mode
- 5.4 Face Picture Comparison
- 5.5 Perimeter Protection
- 5.6 Human Body Detection
- 5.7 Motion Detection
- 5.8 Vehicle Detection
- 5.9 Target Detection
- 5.10 View People Counting Statistics
- 5.11 Heat Map
- Chapter 6 Event
- Chapter 7 File Management
- Chapter 8 POS Configuration
- Chapter 9 Storage
- Chapter 10 Network Settings
- Chapter 11 User Management and Security
- Chapter 12 System Management
- Chapter 13 Appendix
- 13.1 List of Applicable Power Adapter
- 13.2 Glossary
- 13.3 Communication Matrix
- 13.4 Device Command
- 13.5 Frequently Asked Questions
- 13.5.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen live view?
- 13.5.2 Why is the video recorder notifying risky password after a network camera is added?
- 13.5.3 Why is the video recorder notifying the stream type is not supported?
- 13.5.4 How to improve the playback image quality?
- 13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view?
- 13.5.6 How to confirm the video recorder is using H.265 to record video?
- 13.5.7 Why is the timeline at playback not constant?
- 13.5.8 Why is the video recorder notifying the network is unreachable when a network camera is being added?
- 13.5.9 Why is the IP address of network camera being changed automatically?
- 13.5.10 Why is the video recorder notifying IP conflict?
- 13.5.11 Why is image getting stuck when playing back by single or multi-channel cameras?
- 13.5.12 Why does my video recorder make a beeping sound after booting?
- 13.5.13 Why is there no recorded video after the motion detection is set?
- 13.5.14 Why is the device not able to control PTZ camera via coaxitron?
- 13.5.15 Why does the PTZ seem unresponsive via RS-485?
- 13.5.16 Why is the video sound quality not good?
Digital Video Recorder User Manual
155
Chapter 13 Appendix
13.1 List of Applicable Power Adapter
Only use power adapters listed below.
Power Adapter Model
Specifications
Manufacturer
ADS-26FSG-12 12024EPG
12 V, 2 A
Shenzhen Honor Electronic
Co., Ltd.
MSA-Z3330IC12.0-48W-Q
12 V, 3.33 A
Moso Power Supply
Technology Co., Ltd.
MSA-C1500IC12.0-18P-DE
12 V, 1.5 A
0000201935 MOSO
Technology Co., Ltd.
ADS-25FSG-12 12018GPG
CE, 100 to 240 VAC, 12 V, 1.5
A, 18 W, Φ5.5 × 2.1 × 10
0000200174 Shenzhen Honor
Electronic Co., Ltd.
MSA-C1500IC12.0-18P-US
12 V, 1.5 A
0000201935 MOSO
Technology Co., Ltd.
TS-A018-120015AD
100 to 240 VAC, 12 V, 1.5 A,
18 W, Φ5.5 × 2.1 × 10
0000200878 Shenzhen Transin
Technologies Co., Ltd.
MSA-C2000IC12.0-24P-DE
12 V, 2 A
0000201935 MOSO
Technology Co., Ltd.
ADS-24S-12 1224GPG
CE, 100 to 240 VAC, 12 V, 2 A,
24 W, Φ2.1
0000200174 Shenzhen Honor
Electronic Co., Ltd.
MSA-C2000IC12.0-24P-US
US, 12 V, 2 A
0000201935 MOSO
Technology Co., Ltd.
ADS-26FSG-12 12024EPCU
US, 12 V, 2 A
0000200174 Shenzhen Honor
Electronic Co., Ltd.
KPL-040F-VI
12 V, 3.33 A, 40 W
0000203078 Channel Well
Technology Co., Ltd.
MSA-Z3330IC12.0-48W-Q
12 V, 3.33 A
0000201935 MOSO
Technology Co., Ltd.
MSP-Z1360IC48.0-65W
48 V, 1.36 A
0000201935 MOSO
Technology Co., Ltd.
KPL-050S-II
48 V, 1.04 A
0000203078 Channel Well