User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable H.265 Stream Access
- 4.1.3 Manual Recording
- 4.1.4 Configure Recording Schedule
- 4.1.5 Configure Continuous Recording
- 4.1.6 Configure Motion Detection Triggered Recording
- 4.1.7 Configure Event Triggered Recording
- 4.1.8 Configure Alarm Triggered Recording
- 4.1.9 Configure Picture Capture
- 4.1.10 Configure Holiday Recording
- 4.1.11 Configure Redundant Recording and Capture
- 4.1.12 Configure 1080p Lite Mode
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Smart Analysis
- 5.1 Engine Configuration
- 5.2 Task Configuration
- 5.3 Configure Enhanced VCA Mode
- 5.4 Face Picture Comparison
- 5.5 Perimeter Protection
- 5.6 Human Body Detection
- 5.7 Motion Detection
- 5.8 Vehicle Detection
- 5.9 Target Detection
- 5.10 View People Counting Statistics
- 5.11 Heat Map
- Chapter 6 Event
- Chapter 7 File Management
- Chapter 8 POS Configuration
- Chapter 9 Storage
- Chapter 10 Network Settings
- Chapter 11 User Management and Security
- Chapter 12 System Management
- Chapter 13 Appendix
- 13.1 List of Applicable Power Adapter
- 13.2 Glossary
- 13.3 Communication Matrix
- 13.4 Device Command
- 13.5 Frequently Asked Questions
- 13.5.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen live view?
- 13.5.2 Why is the video recorder notifying risky password after a network camera is added?
- 13.5.3 Why is the video recorder notifying the stream type is not supported?
- 13.5.4 How to improve the playback image quality?
- 13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view?
- 13.5.6 How to confirm the video recorder is using H.265 to record video?
- 13.5.7 Why is the timeline at playback not constant?
- 13.5.8 Why is the video recorder notifying the network is unreachable when a network camera is being added?
- 13.5.9 Why is the IP address of network camera being changed automatically?
- 13.5.10 Why is the video recorder notifying IP conflict?
- 13.5.11 Why is image getting stuck when playing back by single or multi-channel cameras?
- 13.5.12 Why does my video recorder make a beeping sound after booting?
- 13.5.13 Why is there no recorded video after the motion detection is set?
- 13.5.14 Why is the device not able to control PTZ camera via coaxitron?
- 13.5.15 Why does the PTZ seem unresponsive via RS-485?
- 13.5.16 Why is the video sound quality not good?
Digital Video Recorder User Manual
153
12.9.4 RTSP Digest Algorithm
RTSP digest algorithm is based on RTSP protocol, it is an algorithm for digest authentication of the
user authentication. You can configure RTSP digest algorithm via web browser.
Go to Configuration → System → Security → Authentication via web browser to select the
required RTSP digest algorithm type.
12.9.5 ISAPI Service
ISAPI (Internet Server Application Programming Interface) is an open protocol based on HTTP,
which can realize the communication between the system devices (e.g., network camera, NVR,
etc.). The device is as a server, the system can find and connect the device.
Steps
1. Go to System → System Service → System Service.
2. Check Enable ISAPI.
3. Click Apply.
4. Restart the device to take effect the settings.
12.9.6 HTTP Authentication
If you need to enable the HTTP service, you can set HTTP authentication to enhance access
security.
Steps
1. Go to Maintenance → System Service → System Service.
Figure 12-22 HTTP Authentication
2. Check Enable HTTP.
3. Select HTTP Authentication Type.
Note
Two authentication types are selectable, for security reasons, it is recommended to select
digest as the authentication type.
4. Click Apply to save the settings.
5. Restart the device to take effect the settings.
12.9.7 HTTP/Web Digest Algorithm
HTTP/Web digest algorithm is based on HTTP protocol, it is an algorithm for digest authentication