User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable H.265 Stream Access
- 4.1.3 Manual Recording
- 4.1.4 Configure Recording Schedule
- 4.1.5 Configure Continuous Recording
- 4.1.6 Configure Motion Detection Triggered Recording
- 4.1.7 Configure Event Triggered Recording
- 4.1.8 Configure Alarm Triggered Recording
- 4.1.9 Configure Picture Capture
- 4.1.10 Configure Holiday Recording
- 4.1.11 Configure Redundant Recording and Capture
- 4.1.12 Configure 1080p Lite Mode
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Smart Analysis
- 5.1 Engine Configuration
- 5.2 Task Configuration
- 5.3 Configure Enhanced VCA Mode
- 5.4 Face Picture Comparison
- 5.5 Perimeter Protection
- 5.6 Human Body Detection
- 5.7 Motion Detection
- 5.8 Vehicle Detection
- 5.9 Target Detection
- 5.10 View People Counting Statistics
- 5.11 Heat Map
- Chapter 6 Event
- Chapter 7 File Management
- Chapter 8 POS Configuration
- Chapter 9 Storage
- Chapter 10 Network Settings
- Chapter 11 User Management and Security
- Chapter 12 System Management
- Chapter 13 Appendix
- 13.1 List of Applicable Power Adapter
- 13.2 Glossary
- 13.3 Communication Matrix
- 13.4 Device Command
- 13.5 Frequently Asked Questions
- 13.5.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen live view?
- 13.5.2 Why is the video recorder notifying risky password after a network camera is added?
- 13.5.3 Why is the video recorder notifying the stream type is not supported?
- 13.5.4 How to improve the playback image quality?
- 13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view?
- 13.5.6 How to confirm the video recorder is using H.265 to record video?
- 13.5.7 Why is the timeline at playback not constant?
- 13.5.8 Why is the video recorder notifying the network is unreachable when a network camera is being added?
- 13.5.9 Why is the IP address of network camera being changed automatically?
- 13.5.10 Why is the video recorder notifying IP conflict?
- 13.5.11 Why is image getting stuck when playing back by single or multi-channel cameras?
- 13.5.12 Why does my video recorder make a beeping sound after booting?
- 13.5.13 Why is there no recorded video after the motion detection is set?
- 13.5.14 Why is the device not able to control PTZ camera via coaxitron?
- 13.5.15 Why does the PTZ seem unresponsive via RS-485?
- 13.5.16 Why is the video sound quality not good?
Digital Video Recorder User Manual
109
Figure 9-6 Create Array
6. Enter Array Name.
7. Select RAID Level as required.
8. Select the physical disks to constitute the array.
Table 9-1 The Required Number of HDDs
RAID Level
The Required Number of HDDs
RAID 0
At least 2 HDDs.
RAID 1
At least 2 HDDs.
RAID 5
At least 3 HDDs.
RAID 6
At least 4 HDDs.
RAID 10
The number of HDD must be an even ranges from 4 to 16.
9. Click OK.
10. Optional: The video recorder will automatically initialize the created array. Go to Storage →
RAID Setup → Array to view the information of the created array.
Figure 9-7 Array List