User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable H.265 Stream Access
- 4.1.3 Manual Recording
- 4.1.4 Configure Recording Schedule
- 4.1.5 Configure Continuous Recording
- 4.1.6 Configure Motion Detection Triggered Recording
- 4.1.7 Configure Event Triggered Recording
- 4.1.8 Configure Alarm Triggered Recording
- 4.1.9 Configure Picture Capture
- 4.1.10 Configure Holiday Recording
- 4.1.11 Configure Redundant Recording and Capture
- 4.1.12 Configure 1080p Lite Mode
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Smart Analysis
- 5.1 Engine Configuration
- 5.2 Task Configuration
- 5.3 Configure Enhanced VCA Mode
- 5.4 Face Picture Comparison
- 5.5 Perimeter Protection
- 5.6 Human Body Detection
- 5.7 Motion Detection
- 5.8 Vehicle Detection
- 5.9 Target Detection
- 5.10 View People Counting Statistics
- 5.11 Heat Map
- Chapter 6 Event
- Chapter 7 File Management
- Chapter 8 POS Configuration
- Chapter 9 Storage
- Chapter 10 Network Settings
- Chapter 11 User Management and Security
- Chapter 12 System Management
- Chapter 13 Appendix
- 13.1 List of Applicable Power Adapter
- 13.2 Glossary
- 13.3 Communication Matrix
- 13.4 Device Command
- 13.5 Frequently Asked Questions
- 13.5.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen live view?
- 13.5.2 Why is the video recorder notifying risky password after a network camera is added?
- 13.5.3 Why is the video recorder notifying the stream type is not supported?
- 13.5.4 How to improve the playback image quality?
- 13.5.5 Why is analog channel having "NO VIDEO" overlaid on live view?
- 13.5.6 How to confirm the video recorder is using H.265 to record video?
- 13.5.7 Why is the timeline at playback not constant?
- 13.5.8 Why is the video recorder notifying the network is unreachable when a network camera is being added?
- 13.5.9 Why is the IP address of network camera being changed automatically?
- 13.5.10 Why is the video recorder notifying IP conflict?
- 13.5.11 Why is image getting stuck when playing back by single or multi-channel cameras?
- 13.5.12 Why does my video recorder make a beeping sound after booting?
- 13.5.13 Why is there no recorded video after the motion detection is set?
- 13.5.14 Why is the device not able to control PTZ camera via coaxitron?
- 13.5.15 Why does the PTZ seem unresponsive via RS-485?
- 13.5.16 Why is the video sound quality not good?
Digital Video Recorder User Manual
x
Safety Instruction
● Proper configuration of all passwords and other security settings is the responsibility of the
installer and/or end-user.
● In the use of the product, you must be in strict compliance with the electrical safety regulations
of the nation and region.
● Firmly connect the plug to the power socket. Do not connect several devices to one power
adapter. Power off the device before connecting and disconnecting accessories and peripherals.
● Shock hazard! Disconnect all power sources before maintenance.
● The equipment must be connected to an earthed mains socket-outlet.
● The socket-outlet shall be installed near the equipment and shall be easily accessible.
● indicates hazardous live and the external wiring connected to the terminals requires
installation by an instructed person.
● Never place the equipment in an unstable location. The equipment may fall, causing serious
personal injury or death.
● Input voltage should meet the SELV (Safety Extra Low Voltage) and the LPS (Limited Power
Source) according to the IEC62368.
● High touch current! Connect to earth before connecting to the power supply.
● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
● Use the device in conjunction with an UPS, and use factory recommended HDD if possible.
● This product contains a coin/button cell battery. If the battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
● This equipment is not suitable for use in locations where children are likely to be present.
● CAUTION: Risk of explosion if the battery is replaced by an incorrect type.
● Improper replacement of the battery with an incorrect type may defeat a safeguard (for
example, in the case of some lithium battery types).
● Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery,
which may result in an explosion.
● Do not leave the battery in an extremely high temperature surrounding environment, which
may result in an explosion or the leakage of flammable liquid or gas.
● Do not subject the battery to extremely low air pressure, which may result in an explosion or
the leakage of flammable liquid or gas.
● Dispose of used batteries according to the instructions.
● Keep body parts away from fan blades and motors. Disconnect the power source during
servicing.
● Keep body parts away from motors. Disconnect the power source during servicing.