User Manual
Table Of Contents
- Chapter 1 Basic Operation
- Chapter 2 Camera Settings
- Chapter 3 Live View
- Chapter 4 Recording and Playback
- 4.1 Recording
- 4.1.1 Configure Recording Parameters
- 4.1.2 Enable the H.265 Stream Access
- 4.1.3 ANR
- 4.1.4 Manual Recording
- 4.1.5 Configure Plan Recording
- 4.1.6 Configure Continuous Recording
- 4.1.7 Configure Motion Detection Triggered Recording
- 4.1.8 Configure Event Triggered Recording
- 4.1.9 Configure Alarm Triggered Recording
- 4.1.10 Configure Picture Capture
- 4.1.11 Configure Holiday Recording
- 4.1.12 Configure Redundant Recording and Capture
- 4.2 Playback
- 4.3 Playback Operations
- 4.1 Recording
- Chapter 5 Event
- 5.1 Normal Event Alarm
- 5.2 VCA Event Alarm
- 5.2.1 Temperature Screening
- 5.2.2 Loitering Detection
- 5.2.3 People Gathering Detection
- 5.2.4 Fast Moving Detection
- 5.2.5 Parking Detection
- 5.2.6 Unattended Baggage Detection
- 5.2.7 Object Removal Detection
- 5.2.8 Audio Exception Detection
- 5.2.9 Defocus Detection
- 5.2.10 Sudden Scene Change Detection
- 5.2.11 PIR Alarm
- 5.2.12 Thermal Camera Detection
- 5.2.13 Configure Queue Management
- 5.3 Configure Arming Schedule
- 5.4 Configure Linkage Actions
- Chapter 6 Smart Analysis
- 6.1 Engine Configuration
- 6.2 Task Configuration
- 6.3 Face Picture Comparison
- 6.4 Perimeter Protection
- 6.5 Human Body Detection
- 6.6 Multi-Target-Type Detection
- 6.7 Vehicle Detection
- 6.8 Target Detection
- 6.9 People Counting
- 6.10 Heat Map
- Chapter 7 File Management
- Chapter 8 Storage
- Chapter 9 POS Configuration
- Chapter 10 Hot Spare Recorder Backup
- Chapter 11 Network Settings
- Chapter 12 User Management and Security
- Chapter 13 System Management
- Chapter 14 Appendix
- 14.1 Glossary
- 14.2 Communication Matrix
- 14.3 Device Command
- 14.4 Frequently Asked Questions
- 14.4.1 Why is there a part of channels displaying “No Resource” or turning black screen in multi-screen of live view?
- 14.4.2 Why is the video recorder notifying not support the stream type?
- 14.4.3 Why is the video recorder notifying risky password after adding network camera?
- 14.4.4 How to improve the playback image quality?
- 14.4.5 How to confirm the video recorder is using H.265 to record video?
- 14.4.6 Why is the timeline at playback not constant?
- 14.4.7 When adding network camera, the video recorder notifies network is unreachable.
- 14.4.8 Why is the IP address of network camera being changed automatically?
- 14.4.9 Why is the video recorder notifying IP conflict?
- 14.4.10 Why is image getting stuck when the video recorder is playing back by single or multi-channel cameras?
- 14.4.11 Why does my video recorder make a beeping sound after booting?
- 14.4.12 Why is there no recorded video after setting the motion detection?
- 14.4.13 Why is the sound quality not good in recording video?
Network Video Recorder User Manual
14
Note
The protocol type and the transfer protocol must be supported by the network camera to add.
3. Click OK.
After adding the customized protocol, you can see it in Protocol.
1.5 Platform Access
1.5.1 Configure ISUP
SDK is based on Intelligent Security Uplink Protocol (ISUP). It provides APIs, library files, and
commands for the third-party platform to access devices such as NVRs, speed domes, DVRs,
network cameras, mobile NVRs, mobile devices, decoding devices, etc. With this protocol, the
third-party platform can realize functions like live view, playback, two-way audio, PTZ control, etc.
Steps
1. Go to System → Network → Advanced → Platform Access.
Figure 1-15 ISUP Settings
2. Select Access Type as ISUP.
3. Check Enable.
Note
Enabling ISUP will disable other platform access.
4. Set the related parameters.
Server Address
The platform server IP address.