iDS-2CD7046G0-AP Network Box Camera Quick Start Guide
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide © 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Warnings Follow these safeguards to prevent serious injury or death. Cautions Cautions Follow these precautions to prevent potential injury or material damage.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide • • The sensor may be burned out by a laser beam, so when any laser equipment is in use, make sure that the sensor surface will not be exposed to the laser beam. Do not place the camera in extremely hot, cold (the operating temperature shall be -30° to +60°C (-22° to 140° F)), dusty or damp locations, and do not expose it to high electromagnetic radiation. • To avoid heat accumulation, good ventilation is required for operating environment.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Table of Contents 1 Appearance Description.............................................................................................................................. 7 2 Installation .................................................................................................................................................. 8 2.1 Memory Card Installation .............................................................................................
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide 1 Appearance Description The box camera overview is shown below: Figure 1, Overview Description No. Description No. Description 1 Lens mount 2 Auto-iris interface 3 Power indicator 4 ¼-20 UNC screw hole The interfaces on the real panel are described as follows. The actual interfaces may vary by model.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide NOTE: Power indicator: red stands for starting and blue for working. To reset the camera default parameters, press and hold the RESET button and power on the camera. After the camera powers on, continue to press and hold the Reset button for 10 seconds. ABF is supported by certain camera models. 2 Installation Before You Start • Make sure the device in the package is in good condition and all the assembly parts are included.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide 2.2 Lens Installation The actual device appearance may vary by model. The following takes a model as an example to illustrate the installation steps. Before You Start The lens shown below is for example only. Figure 3, Lens Installation Steps: 1. Fit the lens (not supplied) to the camera, and rotate it to tighten. NOTES: • • Install the adapter ring to the lens interface if a C-mount lens is used.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Steps 1. Install the pendent mount to the ceiling with the supplied screws. Figure 4, Install the Mount 2. Screw the camera to the pendent mount and tighten the nut. 3. Adjust surveillance angle Adjusting Knob Figure 5, Adjust Surveillance Angle 1) Loosen the adjusting knob.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide 2) Hold the camera body to adjust panning and tilting position. 3) Tighten the knob after adjustment. 4. Adjust zoom and focus level. Refer to Section 2.5. 2.3.2 Wall Mounting Before You Start Wall mount is not included in package. If you adopt this mounting style, you need to prepare a mounting bracket in advance. The shown wall mount is for example. Steps 1. Separate the pedestal from the wall mount. Figure 6, Separate Pedestal 2.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Figure 8, Install Camera to Wall Mount 5. Adjust the surveillance angle. 1) Loosen tilt adjusting screw. Tighten the screw after adjusting. 2) Loosen pan adjusting screw. Tighten the screw after adjusting. Tilt Adjusting Screw Pan Adjusting Screw Figure 9, Adjust Surveillance Angle 6. Adjust zoom and focus level. Refer to Section 2.5. 2.4 Mounting with Housing Before You Start The shown housing is not included in package.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide 2.3.3 Mounting Type I Housing Steps 1. Screw the camera to housing mounting plate. Figure 10, Install Camera to Mounting Plate 2. Screw the mounting plate together with the camera back to the housing. NOTE: Push the camera as close to the window as possible. Window Cable Outlet Figure 11, Install Camera to Housing 3. Connect and route cables through the cable outlet of the housing.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Figure 12, Wiring Board in Housing 4. Buckle the housing. 5. Install the housing to surveillance scene. Using brackets, the housing supports wall mounting, pole mounting, and pendent mounting.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide 3) Install the bracket onto the wall/ceiling/pole. The wall mounting bracket, pole mounting bracket, and the pendent bracket are shown in the figures below. Figure 13, Install the Bracket to Mounting Place (1) Figure 14, Install the Bracket to Mounting Place (2) 4) Fix the housing (with camera) onto the bracket with the supplied screws. 5) Loosen the adjusting screw to adjust the surveillance angle of the camera. Tighten the screw after adjustment.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Figure 16, Fix the Housing to Brackets (2) 6. Adjust zoom and focus. Refer to Section 2.5. 2.3.4 Mounting Type II Housing Steps 1. Connect and route cables through the cable outlet of the housing. 1) For network, alarm input and output, and audio input and output, plug corresponding plugs to the rear panel of the camera. See Figure 1-1. 2) For power supply and RS-485, see the following figure. Figure 17, Wiring Board in Housing 2. Buckle the housing.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide 1) Install the bracket onto the wall/ceiling/pole/ground. The wall mounting bracket, pole mounting bracket, pendent bracket, column mounting bracket, integrated mounting bracket, and junction box are shown in the figures below.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Figure 18, Install the Bracket to Mounting Place 2) Fix the housing (with camera) onto the bracket with the supplied screws. 3) Loosen the adjusting screw to adjust the surveillance angle of the camera. Tighten the screw after adjustment.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide Figure 19, Fix the Housing to Brackets (1) Figure 20, Fix the Housing to Brackets (2) Figure 21, Fix the Housing to Brackets (3) Figure 22, Fix the Housing to Brackets (4) QSG iDS-2CD7046G0-AP 022321NA 19
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide 4. Adjust zoom and focus. Refer to Section 2.5. 2.5 Zoom and Focus Adjustment Steps 1. Power on the camera. 2. Connect the video out interface of the camera to the installation display device. 3. Adjust zoom and focus. • NOTE: • For certain camera models, zoom and focus must be manually adjusted via zoom/focus lever according to the image on the display device.
iDS-2CD7046G0-AP Network Box Camera Quick Start Guide QSG iDS-2CD7046G0-AP 022321NA 21
