Network Dome Camera Quick Start Guide DS-2CD2121G0-IWS/2AX 0
Network Dome Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Dome Camera·Quick Start Guide logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Dome Camera·Quick Start Guide APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information For products that support Wi-Fi or cellular data: (Marked with a “W”, “GLT”, “GLE”, “GLF”, “GE”, “GT” or “GW” in the Part C of a product model. Product Model Example: Part A-Part B-Part C. Part C is optional.
Network Dome Camera·Quick Start Guide —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Network Dome Camera·Quick Start Guide 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.
Network Dome Camera·Quick Start Guide radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Network Dome Camera·Quick Start Guide energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Network Dome Camera·Quick Start Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Network Dome Camera·Quick Start Guide Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network Dome Camera·Quick Start Guide ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Cautions ● Make sure the power supply voltage is correct before using the camera. ● Do not drop the camera or subject it to physical shock. ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
Network Dome Camera·Quick Start Guide ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details.
Network Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 13 1.1 Type I ............................................................................ 13 1.2 Type II ........................................................................... 14 1.3 Type III .......................................................................... 16 1.4 Type IV ..........................................................................
Network Dome Camera·Quick Start Guide 1 Appearance Description There are five types of camera appearance for this series of camera according to the different models. 1.1 Type I 5 6 1 2 7 8 9 3 4 10 Figure 1-1 Overview of Type I Camera Table 1-1 Description of Type I Camera No. Description No.
Network Dome Camera·Quick Start Guide No. Description No. Description 5 Network Interface 6 Power Interface 7 IR LED 8 Lens 9 Black Liner 10 Safety Rope Note: Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.
Network Dome Camera·Quick Start Guide Table 1-2 Description of Type II Camera No. Description No.
Network Dome Camera·Quick Start Guide 1.
Network Dome Camera·Quick Start Guide Table 1-3 Description of Type III Camera No. Description 1 Power supply interface (12 VDC) 2* Audio input and output interface 3* Alarm input and output interface 4 RJ45 self-adaptive network interface (PoE) 5 Mounting base 6 Black liner 7 Lens 8 Bubble 9 Memory card slot 10 Reset button Note: ● The items marked with the "*" are only supported by certain camera models.
Network Dome Camera·Quick Start Guide 1.
Network Dome Camera·Quick Start Guide Table 1-4 Description of Type IV Camera No. Description 1 RJ45 self-adaptive network interface (supports PoE) 2 HDMI 3 Mounting base 4 Black liner 5 Lens 6 Bubble 7 Memory card slot 8 Reset button Note: Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.
Network Dome Camera·Quick Start Guide 4 5 1 2 6 7 8 3 9 Figure 1-5 Overview Of Type V Camera Table 1-5 Description of Type V Camera No. Description No.
Network Dome Camera·Quick Start Guide Note: Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Dome Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or PoE (802.3 af), please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Dome Camera·Quick Start Guide 2.1 Memory Card Installation For camera models that support memory card as local storage, you can follow the steps to mount and unmount the memory card. This camera series shares a similar structure, type III camera is used for demonstration. Steps: 1. Loosen the screws on the bubble. Remove the bubble to expose the memory card slot. Figure 2-1 Remove Bubble Notes: ● In case of losing, screws on bubble cannot be screwed out thoroughly.
Network Dome Camera·Quick Start Guide 2. Find the memory card slot to insert the memory card. Figure 2-2 Insert Memory Card 3. (Optional) To unmount the memory card, push to get it ejected. 2.2 Ceiling Mounting This camera series shares a similar structure, type III camera is used for demonstration. Steps: 1. Paste the drill template to desired mounting place. 2. Drill the screw holes on the ceiling according to the drill template.
Network Dome Camera·Quick Start Guide 1 1 A Drill Template Hole A: for cables routed through the ceiling Screw hole 1: for Mounting Base 1 Figure 2-3 Drill Template Notes: ● If you choose to route cable through the ceiling, cut a cable hole according to Hole A on drill template. ● You can also route cable from the side outlet. ● If you install the camera in outdoor, install the waterproof jacket to the network cable. See Section 2.4.
Network Dome Camera·Quick Start Guide 3. Route the cables and fix the mounting base on the ceiling with three screws. Figure 2-5 Fix the Mounting Base 4. Adjust surveillance angle. See the figure of each camera type for detailed angle adjustment range 1). Loosen one tilting adjust adjusting screw to adjust the tilting position. Tighten the screw after adjustment. 2). Hold the black liner to adjust the panning position. 3). Hold the lens to adjust the rotating position.
Network Dome Camera·Quick Start Guide 0°~360° Tilting Adjust Screw 0°~65° Figure 2-6 Angle Adjustment of Type I Camera Tilt: 0° to 75° Pan: 0° to 355° Tilting Adjust Screw Rotate: 0° to 355° Figure 2-7 Angle Adjustment of Type II Camera 27
Network Dome Camera·Quick Start Guide Figure 2-8 Angle Adjustment of Type III Camera 5. Install the bubble back to the camera.
Network Dome Camera·Quick Start Guide 2.3 Mounting with Brackets This camera series supports mounting with wall mounting bracket, pendant mounting bracket, and incline mounting bracket. We take Type III camera as the demonstration example. 2.3.1 Wall Mounting The wall mounting bracket is not included in the package. You need to prepare one, if you adopt this mounting type. Steps: 1. Mark the screw holes on desired mounting place.
Network Dome Camera·Quick Start Guide 2. Drill 4 screw holes for expansion screws. 3. Unscrew the bubble of the camera. 4. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 5. Route the cables and fix the camera to the cap of the wall mounting bracket with three supplied self-tapping screws. Cable Hole Wall Mounting Bracket Figure 2-11 Fix the Camera to Wall Mounting Bracket 6.
Network Dome Camera·Quick Start Guide Figure 2-12 Fix the Wall Mounting Bracket to Wall 7. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 8. Install the bubble back to the camera.
Network Dome Camera·Quick Start Guide 2.3.2 Wall Mounting with Junction Box The wall mounting bracket with junction box is not included in the package. You need to prepare one, if you adopt this mounting type. Steps: 1. Mark the screw holes on desired mounting place. 2. Fix the bracket to the wall with four expansion bolts. Figure 2-14 Fix the Bracket 3. Unscrew the junction box cover.
Network Dome Camera·Quick Start Guide Cover Figure 2-15 Unscrew the Cover 4. Route and connect the cables. Source cables of network, power, etc., go in from the side outlet of the junction box. Camera cables go in from the cap and the bracket. Note: If you install the camera in outdoor, install the waterproof jacket to the network cable. See Section 2.4. 5. Screw the cover back.
Network Dome Camera·Quick Start Guide Camera Cable Source Cable Figure 2-16 Cable Routing 6. Unscrew the bubble of the camera. 7. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 8. Fix the camera to the cap of the wall mounting bracket with three supplied self-tapping screws.
Network Dome Camera·Quick Start Guide Figure 2-17 Fix the Camera to Wall Mounting Bracket 9. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 10. Install the bubble back to the camera.
Network Dome Camera·Quick Start Guide 2.3.3 Pendant Mounting The pendant mounting bracket is not included in the package. You need to prepare one in advance, if you adopt this mounting type. Steps: 1. Mark the screw holes on desired mounting place. 2. Drill three screw holes for expansion bolts. 3. Route the cables and fix the pendant mounting bracket to ceiling. Cables Figure 2-19 Fix Pendant Mount 4. (Optional) Insert the memory card to the camera, if your camera supports memory card installation.
Network Dome Camera·Quick Start Guide Cap Figure 2-20 Fix the Camera to Cap 6. Screw the cap to the pendant mounting bracket.
Network Dome Camera·Quick Start Guide 7. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 8. Install the bubble back to the camera. 2.3.4 Incline Mounting The incline mounting bracket is not included in the package. You need to prepare one, if you adopt this mounting type. Steps: 1. Paste the drill template to desired mounting place. Ceiling Mounting Screw Hole Screw Hole Cable Hole Figure 2-22 Drill Template 2.
Network Dome Camera·Quick Start Guide Figure 2-23 Fix Incline Mounting Bracket to Wall 4. Unscrew the bubble of the camera. 5. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 6. Route the cables and fix the camera to the incline mounting bracket with three supplied self-tapping screws. Note: If you install the camera in outdoor, install the waterproof jacket to the network cable. See Section 2.4.
Network Dome Camera·Quick Start Guide 7. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 8. Install the bubble back to the camera. Figure 2-25 Install the Bubble 2.4 (Optional) Network Cable Waterproof Jacket Installation Purpose: If the camera is installed outdoor, you can adapt the waterproof accessory for the network cable after the camera is secured on the installation surface.
Network Dome Camera·Quick Start Guide ① ② ③ ④ ⑤ ⑥ ⑦ Figure 2-26 Waterproof Accessory Components Table 2-1 Components No. Components 1 Camera’s Network Interface Socket 2 O-Type Gasket 3 Network Plug 4 Waterproof Endcap 5 Waterproof Rubber Gasket 6 Lock Nut 7 Network Cable from Router/Switch Steps: 1. Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (rubber gasket inset ridge must face waterproof endcap), and the waterproof endcap ④ in order. 2.
Network Dome Camera·Quick Start Guide 3. Place the O-type gasket ② onto the end of the camera’s network interface socket ①. 4. Insert the network plug ③ into the camera’s network interface socket ①. 5. Insert the waterproof rubber gasket ⑤ into the waterproof endcap ④, and secure lock nut ⑥ with the waterproof endcap ④. 6.
Network Dome Camera·Quick Start Guide 3 Set the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Dome Camera·Quick Start Guide 3.2 Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are all supported. We will take activation via SADP software and activation via web browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Dome Camera·Quick Start Guide Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Dome Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch.
Network Dome Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Dome Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP.
Network Dome Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Dome Camera·Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Dome Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Dome Camera·Quick Start Guide 5 Operate via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Dome Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Dome Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Dome Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Add Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Dome Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Dome Camera·Quick Start Guide 5.4 Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
UD07705B 0
