Handheld Thermal Monucular Camera UD17958B
Legal Information ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website ( https://www.hikvision.com/ ).
PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Warning This is a class B product. In a domestic environment this product may cause radio inter-ference in which case the user may be required to take adequate measures.
Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Note Provides additional information to emphasize or supplement important points of the main text.
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. Laws and Regulations • Use of the product must be in strict compliance with the local electrical safety regulations. Transportation • Keep the device in original or similar packaging while transporting it. • Keep all wrappers after unpacking them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper.
• Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary. • If the equipment is used in a manner not specified by the manufacturer, the protection provided by the device may be impaired. Using Environment • Make sure the running environment meets the requirement of the device. The operating temperature shall be -30°C to 55°C (-22°F to 131°F), and the operating humidity shall be 95% or less. • DO NOT expose the device to high electromagnetic radiation or dusty environments.
User Manual of Electrical Version Scan the QR code to view the user manual on your mobile phone. Note that mobile data charges may apply if Wi-Fi is unavailable.
1 Overview 1.1 Brief Description The handheld observational thermal monocular is a handheld device with functions of observation, highest temperature target tracking, distance measurement, Wi-Fi hot spot, and so on. The high-sensitivity built-in thermal detector provides you with clear view even in total darkness. The device is mainly applied to outdoor scenarios such as patrolling, law enforcement, searching and rescuing, drug enforcement, anti-smuggling, criminal seizing, hiking, travel, and hunting, etc.
Table 1-1 Function of Button Icon Button Function Power Press: standby mode on/ off Hold: power on/off Mode Press: palettes Hold: FFC Capture Press: capture Hold: start/stop recording Menu Hold: display menu or not Zoom Press: digital zoom 1.3.2 Interface Figure 1-2 Overview of Interfaces • Lens Cover: protect the lens from dust or scratch. • Diopter Adjustment Knob: adjust the view according to your degree of myopia.
USB Cable × 1 User Manual × 1 No-Dust Cloth × 1 Neck Belt × 1 Thermal Camera × 1 Protective Bag × 1 2.2 Charge Device After the device starts up, the OSD (on-screen display) shows the battery status. When the battery is low, charge the device and ensure it works properly. Before You Start • The charging temperature should be from 0 °C to 45 °C (32 °F to 113 °F). • Charge the device with the delivered USB cable. Steps 1. Lift the USB cover. 2. Plug in the USB cable and charge the device.
When the device is connected to USB cable or the battery is enough, press for 2 seconds to power on the device. Power Off When the device is turned on, hold off the device. for 2 seconds to power 2.4 Menu Description When the device powers on, hold to display the menu. Figure 2-2 Menu Description • Press to move the cursor up. • Press to move the cursor down. • Press to confirm and hold it to exit the menu.
Figure 3-2 Adjust Diopter 3.2 Adjust Brightness to adjust brightness. In white hot mode, Select and press the higher the value of brightness is, the brighter the image is. The image effect in white hot mode is showed as picture below and effect in black hot mode is opposite. Figure 3-3 Adjust Brightness in White Hot Mode 3.3 Adjust Contrast Select and press to adjust image contrast. 3.4 Select Scene You can select proper scene according to environment temperature to improve the display effect.
Black Hot The hot part is black-colored in view. The higher the temperature is, the more black the color is. Red Hot The hot part is red-colored in view. The higher the temperature is, the redder the color is. Fusion From high temperature to low temperature, the image is colored in from white, yellow, red, pink to purple. 3.6 Adjust Digital Zoom You can zoom the image by using this function. in the view mode, the live view switches between 1 ×, 2 Press ×, and 4 ×. 3.
Figure 3-4 Flat Field Correction 3. Hold to save the settings and exit. 3.8 Correct Defective Pixel The device can correct the defective pixels on the screen which are not performed as expected. Steps 1. Hold to show the menu. 2. Select . 3. press to select the offset. The offset refers to the moving length of cursor. 4. Press or to select the moving direction. 5. Press to move the cursor to the position of dead pixel. Hold to correct the dead pixel.
Note The available height ranges from 0.1 m to 9.9 m. 3) Press to confirm. 3. Align the center of top mark with the edge of target top. Press . Figure 4-1 Set the Edge of Target Top The cursor blinks on the top edge of the target. 4. Align the center of bottom mark with the edge of target bottom. Press . Figure 4-2 Set the Edge of Target Bottom Result The left top of the image displays the distance measurement result and the height of the target.
When the function is enabled, displays in the spot of highest temperature. When the scene changes, the moves. 6 Picture and Video You can manually record video or capture picture when displaying live view. 6.1 Capture Picture On the main live view page, press to capture picture. Note • When capturing succeeds, the image freezes for 1 second and a prompt shows on the display. • For exporting captured pictures, refer to Export Files. 6.2 Record Video Steps 1.
Note • The device displays images when you connect it to PC. But functions such as recording, capturing and hot spot are disabled. • When you connect the device to PC for the first time, it installs the drive program automatically. 7 Client Software Connection Connect the device to the T-Vision APP via hot spot, then you can capture picture, record video, or configure parameters on your phone. Before You Start Install the T-Vision APP on your phone first.
Steps 1. Hold to show the menu of device. 2. Select , and press . You can view the device information such as version, and serial No. 9.2 Upgrade Device Before You Start Please get the upgrade package first. Steps 1. Connect the device to your PC with USB cable. 2. Open the detected disk, copy the upgrade file and paste it to the root directory of the device. 3. Disconnect the device from your PC. 4. Reboot the device. Result The device upgrades automatically.
10.5 Why the PC cannot identify the device? Check the following items. • Whether the device is connected to your PC with supplied USB cable. • If you use other USB cables, make sure the cable length is no longer than 1 m. • Whether the hot spot function is turned on. If so, go to device menu and turn off hot spot. 11 Appendix 11.1 Device Command Scan the following QR code to get device common serial port commands.
