Network Dome Camera ECI-D64Z2 Quick Start Guide
ECI-D64Z2 Network Dome Camera Quick Start Guide Manual Illustrations and Features Graphics (screen shots, product pictures, etc.) in this document are for illustrative purposes only. Your actual product may differ in appearance. Your product might not support all features discussed in this document. Hikvision USA Inc., 18639 Railroad St.
ECI-D64Z2 Network Dome Camera Quick Start Guide CONFORMS TO THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ECI-D64Z2 Network Dome Camera Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions.” Warnings: Serious injury or death may occur if any of the warnings are neglected.
ECI-D64Z2 Network Dome Camera Quick Start Guide • The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. • Do not place the camera in extremely hot, cold (the operating temperature shall be -30° to +60° C, or -40° to +60° C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
ECI-D64Z2 Network Dome Camera Quick Start Guide Table of Contents 1 Appearance ...................................................................................................................... 6 1.1 Camera Overview ...................................................................................................... 6 1.1.1 Overview .......................................................................................................... 6 2 Installation.................................................
ECI-D64Z2 Network Dome Camera Quick Start Guide 1 Appearance This camera series consists of several different models. Some models are equipped with a zoom lens, in which focus levels must be manually adjusted via a zoom/focus lever. Other models have a motor-driven lens, which allow for zoom and focus adjustment to be completed via web browser or client software. Please refer to the actual device. 1.1 Camera Overview 1.1.1 Overview Camera overview is shown below.
ECI-D64Z2 Network Dome Camera Quick Start Guide ● The wall is strong enough to withstand four times the weight of the camera and mount. For IR cameras, take the following precautions in order to prevent IR reflection: ● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until installation is complete. If there is dust or grease on the dome cover, clean the dome cover with a soft cloth and isopropyl alcohol.
ECI-D64Z2 Network Dome Camera Quick Start Guide Memory Card Figure 2-2 Install the Memory Card 3. (Optional) Unmount the memory card by ejecting it. 2.2 Mounting 2.2.1 Ceiling Mount Steps: 1. Fix the supplied drill template to the area where you would like to install the camera. 2. Drill three screw holes and a cable hole (optional) into the ceiling according to the drill template. 43 .3 mm (1 .7" ) 25 mm 50 mm (0.98" ) (1.97" ) 50.3 mm (1.98" ) 58 mm (2.28" ) 29 mm (1.
ECI-D64Z2 Network Dome Camera Quick Start Guide Back Box Figure 2-4 Secure the Camera Note: ● The supplied screw package contains self-tapping screws and expansion bolts. ● For cement ceilings, secure the camera with expansion bolts. For wooden ceilings, use self-tapping screws. 5. Connect corresponding cables, such as the power cord and network cable. 6.
ECI-D64Z2 Network Dome Camera Quick Start Guide Side Outlet Waterproof Plug Figure 2-6 Remove the Waterproof Plug 2. Route the cables through the side outlet towards the conduit. 3. Insert the conduit into the outlet and tighten counterclockwise. Conduit Figure 2-7 Install the Cable Conduit Note: When mounting on a wall, position the side outlet downwards to prevent the collection of water. Downward Figure 2-8 Conduit Outlet Direction 2.
ECI-D64Z2 Network Dome Camera Quick Start Guide To a monitor Auxiliary Video Cable Auxiliary Video Output Figure 2-9 Connect Camera to a Monitor Note: For certain camera models, the auxiliary video cable is not included in the package. Instead, you can connect the video out interface of the camera to a monitor for image and focus adjustment. Video Out Interface Figure 2-10 Camera Video-Out Interface 2.3.1 3-Axis Adjustment Steps: 1. View camera output on the monitor. 2.
ECI-D64Z2 Network Dome Camera Quick Start Guide 2. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the ideal viewing angle. Zoom/Focus Lever Figure 2-12 Zoom/Focus Lever (Type II Camera) 3. Tighten the zoom lever. 4. Loosen the focus lever and move the lever between F (Far) and N (Near) to obtain the optimum focus. 5. Tighten the focus lever. Motor-Driven Lens: Some camera models in this series are equipped with a motor-driven lens.
ECI-D64Z2 Network Dome Camera Quick Start Guide or or tw Ne le ab kC Ne two rk Cab le or Network Camera Computer Figure 3-2 Connect via a Switch or a Router 3.2 Activate the Camera Activate the camera by setting a strong password. Activation via web browser, activation via SADP, and activation via client software are supported. Activation via SADP software and web browser will be used as examples to introduce camera activation.
ECI-D64Z2 Network Dome Camera Quick Start Guide STRONG PASSWORD RECOMMENDED – We highly recommend creating a strong password of your own choosing (using a minimum of eight characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. We recommend regularly resetting your password on a weekly or monthly basis, especially in high security systems. 4. Confirm the password. 5.
ECI-D64Z2 Network Dome Camera Quick Start Guide 4. Click Activate to start activation. You can check whether the activation is complete in the popup window. If activation failed, make sure that the password meets the requirements, and try again. 3.3 Modify the IP Address Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet as your PC. Use the SADP software or client software to search and change the IP address of the device.
ECI-D64Z2 Network Dome Camera Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above CPU: 2.0 GHz or greater RAM: 1 Gb or greater Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 or higher, Apple Safari 5.0.2 or higher, Mozilla Firefox 5.0 or higher, and Google Chrome 18 or higher Steps: 1. Open the Web browser. 2.
ECI-D64Z2 Network Dome Camera Quick Start Guide 6. Reopen the Web browser after plug-in installation and repeat steps 2 to 4 in order to login. Note: For further configuration instructions, please refer to the network camera user manual. 5 Hik-Connect Purpose: Hik-Connect is a mobile application to view live camera images, receive alarm notifications, etc. 5.1 Enable Hik-Connect for Use with Cameras Purpose: Enable Hik-Connect should on your camera before using the service.
ECI-D64Z2 Network Dome Camera Quick Start Guide 5.2.1 Enable Hik-Connect via a Web Browser Before You Start: Activate the camera before enabling the service. Refer to Chapter 3.2. for more information. Steps: 5. Access the camera via the Web browser. Refer to Chapter 4. 6. Enter the platform access configuration interface, as follows: Configuration > Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 7. Set the Platform Access Mode to Hik-Connect. 8.
ECI-D64Z2 Network Dome Camera Quick Start Guide Figure 5-3 Connect a Router Note: After the camera connects to the network, wait one minute before using the camera with Hik-Connect. 2. Add the camera to the Hik-Connect app: • If Accessing the Camera through an NVR: Tap “+” on the upper-right corner and scan the QR code that appears in the NVR interface. • If Accessing the Camera through a Web Browser: Tap the camera’s serial number. icon and type in the 3. Input your camera’s verification code.
ECI-D64Z2 Network Dome Camera Quick Start Guide QSG VE ECI-D64Z2 041118NA 20
