Mobile Video Recorder Quick Start Guide
Mobile Video Recorder Quick Start Guide Legal Information Quick Start Guide ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. ("Hikvision") reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Mobile Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Mobile Video Recorder Quick Start Guide equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
Mobile Video Recorder Quick Start Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Mobile Video Recorder Quick Start Guide Contents Chapter 1 Installation and Connection ........................................................................................ 1 1.1 Before You Start ..................................................................................................................... 1 1.2 Environment .......................................................................................................................... 1 1.3 Install SIM Card ..............................
Mobile Video Recorder Quick Start Guide 5.3 Why does my device fail to position? .................................................................................. 13 5.4 Why does my device make a beeping sound after startup? ................................................
Mobile Video Recorder Quick Start Guide Chapter 1 Installation and Connection Note Device pictures in this section are only for reference. In condition that device pictures conflict with the real devices, the later prevails. 1.1 Before You Start Take out the device from the package. Check the device and accessories. Contact us if something is missing or damaged. 1.2 Environment Consider the following environment conditions when installing the device.
Mobile Video Recorder Quick Start Guide Fixing position All the screws in the fixing positions must be fastened tightly to avoid device falling during the vibration in driving. 1.3 Install SIM Card Pluggable 3G/4G wireless communication module is designed for the device. Install SIM card to realize wireless communication. Before You Start Prepare SIM card and wrench. Steps Note This section is only applicable to the device supporting 3G/4G and Wi-Fi. 1. Wear antistatic gloves. 2.
Mobile Video Recorder Quick Start Guide Table 1-1 Antenna Interface Interface • • • • Corresponding Antenna M-ANT/ Main 3G/4G antenna AUX Aux Wi-Fi antenna WIFI/ Main Wi-Fi antenna GNSS/ Positioning antenna Place antenna vertically with its signal receiving end facing upward. If the cable is too long, you can roll them up to prevent signal receiving from being affected. Install 3G/4G antenna in car windshield, seat backrest, or other non-metallic objects.
Mobile Video Recorder Quick Start Guide Before You Start Prepare the key to dummy HDD (delivered with device) and SD card. Steps 1. Wear antistatic gloves. 2. Insert the key and turn counterclockwise to unlock dummy HDD. 3. Unfasten the two screws of dummy HDD and pull it out of device. 4. 5. 6. 7. Figure 1-5 Pull Dummy HDD out Open the cover of SD card slot. Insert SD card into SD card slot till you hear a click.
Mobile Video Recorder Quick Start Guide Chapter 2 Device Wiring 2.1 Power Cord Wiring Warning • In order to ensure the safety of your automobile and device, a fuse is required for wiring of automobile power and device power. • Do not connect the power cord to the device before all the cables are connected. 2.1.1 Shutdown Delay The device starts up when your automobile ignites and shuts down after automobile is off.
Mobile Video Recorder Quick Start Guide Result Figure 2-2 Shutdown Delay Note • Contact the automobile manufacturer for the connection information of starting switch. • The automobile ignition switch, also called car key, controls the startup and shutdown of your automobile. Most of automobiles adopt positive pole ignition switch currently. • The normal automobile power refers to the main power of the automobile power supply system.
Mobile Video Recorder Quick Start Guide Result Figure 2-4 Scheduled Shutdown 2.2 Alarm Input Connection The device adopts the high/low-level electrical signals triggering (high level: 6 to 36 VDC; low level: 0 to 5 VDC) to realize alarm input. And in order to avoid error report caused by voltage fluctuation, no alarm will be triggered by voltage ranging of 5 to 6 VDC. Figure 2-5 Alarm Input Connection 2.3 Sensor-In Wiring Steps 1. Connect the delivered extension cable to I/O interface. 2.
Mobile Video Recorder Quick Start Guide Figure 2-6 Sensor-In Wiring 2.4 Power on Device Connect the device to power supply after all the installations above are finished. You can view the indicators to get knowledge of the device status. Note The indicator types vary with different models. Here the most comprehensive indicators are introduced. • Power indicator (PWR) • Solid green: Device is powered on. • Solid red: Device is standby. • Ready indicator (RDY) Solid green: Device starts up normally.
Mobile Video Recorder Quick Start Guide Chapter 3 Activation For the first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation. 3.1 Default Information Device default IP address and user name are as follows. • Default IP address: 192.168.1.64 • Default user name: admin. 3.2 Activate Device Activation via local menu operation, web browser, SADP, and client software are all supported. In this section, we introduce activation via web browser.
Mobile Video Recorder Quick Start Guide Chapter 4 Basic Operation 4.1 3G/4G Dialing Before You Start Install SIM card and 3G/4G antenna. Steps 1. Go to Configuration → Network → Basic Settings → 3G/4G . 2. Check Enable. 3. Click Dial Parameters. 4. Click Save and reboot the device to activate the new settings. 5. Optional: Click Wireless Dial-up Status to view dialing status. 4.2 Mobile Surveillance Platform Connection The device can be remotely accessed via mobile surveillance platform.
Mobile Video Recorder Quick Start Guide The ID of the device registered on the eHome platform. If you leave it empty, device logs in to the platform with serial No. 5. Click Save and reboot the device to activate the new settings. 4.3 IP Camera Management The chapter is only available for device supporting IP camera feature. 4.3.1 Activate IP Camera Before adding an IP camera, activate it by setting a password. Steps 1. Go to Configuration → System → Camera Management . 2. Select an inactive IP camera.
Mobile Video Recorder Quick Start Guide Note If the passwords of the device and camera are same, click Quick Add to add the camera. 4. Enter IP camera information. 5. Click OK. 4.3.3 Edit IP Camera You can visit, delete, and modify the added IP cameras. Before You Start If the device contains only one network card, you can visit IP camera via the device directly. If the device contains dual network cards, you need to enable virtual host function before visiting IP camera.
Mobile Video Recorder Quick Start Guide Chapter 5 FAQ 5.1 Why does my device fail to start up after connecting the power? Question Why does my device fail to start up after connecting the power? Answer • Check power supply specification. • If PWR indicator is unlit, check power supply and fuse installation. • If PWR indicator is red, lock the dummy HDD. 5.2 Why does my device fail to dial? Question Why does my device fail to dial? Answer • • • • Check 3G/4G antenna connection.
Mobile Video Recorder Quick Start Guide Answer • Install at least one HDD and format it after installation. • Go to HDD management interface to check HDD status. Replace it with a good one when it is error. • Go to exception settings interface to cancel the beeping sound and use the device without HDD.
UD12581B-A