Quick Start Guide

1 2 2
3
1 2
2
2
1
3 4
6 7
5
5
6
4
3
1
DS-KH6320-WTE2
Video Intercom Two-Wire Indoor Staon
Diagram References
ENGLISH
Appearance
Installaon
Before you begin:
Wall Mounng with Juncon Box
Acvate Indoor Staon
1
3
Geng Started
4
Wiring
2
Display Screen
Microphone
Debugging Port
1 2 3
4
5 6 7
1. Tools that you need to prepare for installaon: Make sure the device in the package is in good condion
and all the assembly parts are included.
2. The power supply the indoor staon supports is 12 VDC. Please make sure your power supply matches
your indoor staon.
3. Make sure all the related equipment is power-off during the installaon.
4. Check the product specificaon for the installaon environment.
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm (length) × 50 mm (depth).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate hooks into the slots on the
rear panel of the indoor staon, during which the lock catch will be locked automacally.
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automacally.
3. Configure the indoor staon and tap Next.
a. Choose Indoor Staon Type.
b. Edit Floor and Room No.
4. Linked related devices and tap Next. If the device and the indoor staon are in the same LAN, the
device will be displayed in the list. Tap the device or enter the serial No. to link.
a. Tap the door staon in the list to link.
b. Tap the sengs icon to pop up the Network Sengs page.
c. Edit the network parameters of the door staon manually or enable DHCP to get the network
parameters automacally.
d. Oponal: Enable Synchronize Language to synchronize the Language of door staon with indoor
staon.
e. Tap OK to save the sengs.
5. Tap Finish to save the sengs.
1. Power on the device. It will enter the acvaon page automacally.
2. Create a password and confirm it.
3. Tap OK to acvate the indoor staon.
TF Card Slot
Loudspeaker
Two-Wire Interface
Alarm Terminal
Note: The debugging port is used for debugging only.
Diagram References
ENGLISH
Appearance
1
Power Indicator
Terminals
1 2
3
4 5 6Power Input
LAN
Network Indicator
Reset
There are 20 pins in the terminal on the rear panel of the indoor staon: 2 RS-485 pins, 5 reserved pins, 4
relay output pins, 8 alarm input pins, and 1 GND pin.
The wall mounng plate and the juncon box are required to install the indoor staon onto the wall.
The dimension of juncon box should be 75 mm (width) × 75 mm (length) × 50 mm (depth).
The dimension of wall mounng plate is shown.
Installaon
Before you begin:
3
Wiring
2
Make sure the device in the package is in good condion.
Make sure all the related equipment is power-off during the installaon.
Check the product specificaon for the installaon environment.
Wire the devices with power supply cables.
Door staon should be connected to CH4 of the video/audio distributor with two-wire cables.
Indoor Staon should be connected to any terminal of CH1 to CH3 of the video/audio distributor with
two-wire cables.
Cauon: Make sure all the related equipment is power-off during the installaon.
Note:
The power output of CH1 to CH3: 12 VDC, Max. 6W.
The power output of CH4: 12 VDC, Max. 8W.
Wire the devices with power supply cables.
Door staon should be connected to CH4 of the video/audio distributor with two-wire cables.
Indoor Staon should be connected to any terminal of CH1 to CH3 of the video/audio distributor with
two-wire cables.
Cauon: Make sure all the related equipment is power-off during the installaon.
Note:
The power output of CH1 to CH3: 12 VDC, Max. 6W.
The power output of CH4: 12 VDC, Max. 8W.
1. Fix the DIN rail onto the wall.
Note: You are required to ulize a matched DIN rail.
2. Press the red clip upward, and lock it to the DIN rail.
Note: Wiring descripon refers to the User Manual.
Refer to Video Intercom Indoor Staon Configuraon Guide (scan the QR code) for details.
Refer to Video Intercom Indoor Staon Operaon Guide (scan the QR code) for details.
DS-KAD704
Video Intercom Two-Wire Video/Audio Distributor
RS-485+
RS-485-
Red
RES
RES
RES
RES
RES
Blue
Green
Yellow
Yellow
Red
AIN1
White
White
White
AIN2White
AIN3White
AIN4White
AIN5White
AIN6White
AIN7Black
AIN8Black
NO2Black
NO1Black
COM2Red
COM1Black
GND
Alarm
Input
Device
Relay Output
Reserved
RS-485
Rear Panel (without Interface)
Screw
Wall Mounng Plate
Lock Catch Lock Catch
Lock CatchLock Catch
Juncon Box Wall
Hook
Hook
Hook
Hook
64.85±0.1 mm
83.3±0.1 mm
6.7±0.15 mm
26 mm 4.2 mm
2.3 mm
60±0.1 mm
32 mm
1 mm
3.5 mm
84.85±0.1 mm
53.5±0.15 mm
61±0.1 mm
Φ5
NetworkNetwork
Door Staon
Video/Audio Distributor
Power Adapter
(Oponal)
Indoor Staon
You are required to acvate the device first by seng a strong password for it before
you can use the device.
1
Quick Configuraon
2
2
1
34