Video Intercom Door Station (D Series) Quick Start Guide UD02925B
Video Intercom Door Station·Quick Start Guide Quick Start Guide © 2016 Hangzhou Hikvision Digital Technology Co., Ltd. This quick start guide is intended for users of the models below: Series Model DS-KD8102-V Door Station (D Series) DS-KD8002-VM DS-KD6002-VM It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection.
Video Intercom Door Station·Quick Start Guide SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. Support Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Door Station·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Door Station·Quick Start Guide 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.
Video Intercom Door Station·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Video Intercom Door Station·Quick Start Guide Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Video Intercom Door Station·Quick Start Guide Table of Contents 1 Appearance .................................................................................................. 1 1.1 Appearance of DS-KD8102-V ................................................................................... 1 1.2 Appearance of DS-KD8002-VM ................................................................................ 2 1.3 Appearance of DS-KD6002-VM ........................................................................
Video Intercom Door Station·Quick Start Guide Installation Notice ........................................................................................................37 Wiring Cables ...............................................................................................................
Video Intercom Door Station·Quick Start Guide 1 Appearance 1.1 Appearance of DS-KD8102-V Figure 1-1 Front View Figure 1-2 Side View Table 1-1 Descriptions of Keys No.
Video Intercom Door Station·Quick Start Guide 9 IR Emission 10 IR Receiver 11 Loudspeaker 12 TAMPER 1.2 Appearance of DS-KD8002-VM 10 Figure 1-3 Front View Figure 1-4 Side View Table 1-2 Descriptions of Keys No.
Video Intercom Door Station·Quick Start Guide 7 Call Button 8 Microphone 9 Call Center Key 10 TAMPER 1.3 Appearance of DS-KD6002-VM Figure 1-5 Front View Figure 1-6 Rear View Table 1-3 Descriptions Keys No.
Video Intercom Door Station·Quick Start Guide No.
Video Intercom Door Station·Quick Start Guide 2 Terminals and Interfaces 2.1 Terminals and Interfaces of DS-KD8102-V/ DS-KD8002-VM Figure 2-1 Terminals and Interfaces of DS-KD8102-V/DS-KD8002-VM Table 2-1 Descriptions of Terminals and Interfaces Name No.
Video Intercom Door Station·Quick Start Guide Name ALARM OUT ALARM IN DOOR RS485 SENSOR No.
Video Intercom Door Station·Quick Start Guide 2.2 Terminals and Interfaces of DS-KD6002-VM Figure 2-2 Terminals and Interfaces of DS-KD6002-VM Table 2-2 Descriptions of Terminals and Interfaces Name No.
Video Intercom Door Station·Quick Start Guide Name ALARM OUT DEBUG DOOR RS485 ALARM IN No. Interface Description B1 AO2- B2 AO2+ B3 AO1- B4 AO1+ B5 GND Grounding B6 RX Serial Port Debugging/Receive data B7 TX Serial Port Debugging/Send data B8 3.
Video Intercom Door Station·Quick Start Guide 3 Installation and Wiring Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station. Make sure all the related equipment is power-off during the installation. Check the product specification for the installation environment. 3.
Video Intercom Door Station·Quick Start Guide The dimension of gang box for model DS-KD8102-V door station is: 404 (length)×123 (width)×47.5 (depth) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. 3.1.2 Wall Mounting with Gang Box of DS-KD8102-V Steps: 1. Chisel a hole in the wall for inserting the gang box. The size of the hole should be larger than that of the gang box. The suggested size of hole is 404.5 (length) × 123.
Video Intercom Door Station·Quick Start Guide Figure 3-4 Install the Door Station 5. Pull the door station downward and then push it towards the inside to make sure it fits the hole. 6. Tighten the screws of the door station with the Allen wrench.
Video Intercom Door Station·Quick Start Guide 3.2 Installation of DS-KD8002-VM 3.2.1 Gang Box for DS-KD8002-VM 135 407.5 7.6 Figure 3-6 Front View 9 9 Figure 3-7 Overhead (Plan) View The dimension of gang box for model DS-KD8002-VM door station is: 407.5 mm × 135 mm × 55 mm. The dimensions above are for reference only. The actual size can be slightly larger than the theoretical dimension. 3.2.2 Wall Mounting with Gang Box of DS-KD8002-VM 1. Chisel a hole in the wall for inserting the gang box.
Video Intercom Door Station·Quick Start Guide 8.75 118 8.75 408 384 135.5 55 Figure 3-8 Dimensions of the Hole 2. Insert the gang box into the hole and fix it with 4 PA4 screws. Figure 3-9 Insert the Gang Box into the Wall 3. Make sure the edges of the gang box align to the wall and the hook A and hook B of the gang box hook onto the wall. 4. Route the cables of the door station through the cable hole. 5.
Video Intercom Door Station·Quick Start Guide Figure 3-10 Install the Door Station 7. After fixing the door station onto the gang box, secure it by inserting the plate and insert 2 POM2 screws.
Video Intercom Door Station·Quick Start Guide 3.3 Installation of DS-KD6002-VM 3.3.1 Gang Box for DS-KD6002-VM Figure 3-12 Front and Side View The dimension of gang box for model DS-KD6002-VM door station is: 343(length)× 113(width)×55(depth) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. 3.3.2 Wall Mounting with Gang Box of DS-KD6002-VM Steps: 1. Chisel a hole in the wall for inserting the gang box.
Video Intercom Door Station·Quick Start Guide Screw Screw Figure 3-13 Insert the Gang Box into the Wall 3. Make sure the edges of the gang box align to the wall. 4. Route the cables of the door station through the cable hole. 5. Put the door station into the gang box. Figure 3-14 Install the Door Station 6. Fix the door station to the gang box with 4 crews.
Video Intercom Door Station·Quick Start Guide Figure 3-15 Tighten the Screws of Device 3.4 Wiring Description 3.4.1 Door Lock Wiring Figure 3-16 Door Lock Wiring Terminal NO1/COM1 is set as default for accessing magnetic lock/electric bolt; terminal NC1/COM1 is set as default for accessing electric strike.
Video Intercom Door Station·Quick Start Guide To connect electric lock in terminal NO2/COM2/NC2, it is required to set the output of terminal NO2/COM2/NC2 to be electric lock with Batch Configuration Tool or iVMS-4200. 3.4.2 Door Magnetic Wiring Door Magnetic Wiring for DS-KD8102-V/DS-KD8002-VM For DS-KD8102-V/DS-KD8002-VM, there are two optional ways of door magnetic wiring.
Video Intercom Door Station·Quick Start Guide Terminal S2 is set as default for connecting door magnetic. Door Magnetic Wiring for DS-KD6002-VM Figure 3-19 Door Magnetic Wiring for DS-KD6002-VM To connect the door magnetic, it is required to set the output of terminal AI2 to be door magnetic with Batch Configuration Tool or iVMS-4200. 3.4.3 Exit Button Wiring Exit Button Wiring for DS-KD8102-V/DS-KD8002-VM For DS-KD8102-V/DS-KD8002-VM, there are two optional ways of exit button wiring.
Video Intercom Door Station·Quick Start Guide To connect the exit button, it is required to set the output of terminal AI1 to be exit button with Batch Configuration Tool or iVMS-4200. Figure 3-21 Exit Button Wiring for DS-KD8102-V/DS-KD8002-VM (2) Exit Button Wiring for DS-KD6002-VM Figure 3-22 Exit Button Wiring for DS-KD6002-VM Terminal S1 is set as default for connecting exit button.
Video Intercom Door Station·Quick Start Guide 3.4.4 External Card Reader Wiring Please set the DIP switch first before connecting the card reader. If the DIP switch should be configured when the card reader is power-on, please reboot the card reader after configuring the DIP switch. The DIP switch description is shown in the following table: No.
Video Intercom Door Station·Quick Start Guide Wiegand Card Reader Wiring Figure 3-24 External Card Reader Wiring 3.4.
Video Intercom Door Station·Quick Start Guide Alarm Device Input Wiring for DS-KD6002-VM Figure 3-26 Alarm Device Input Wiring for DS-KD6002-VM 3.4.
Video Intercom Door Station·Quick Start Guide Alarm Device Output Wiring for DS-KD6002-VM Figure 3-28 Alarm Device Output Wiring for DS-KD6002-VM 24
Video Intercom Door Station·Quick Start Guide 4 Before You Start For the first time use of the device, you are required to activate the device and set the device password. You can activate the device via internet with Batch Configuration Tool, or with iVMS-4200 client software. To activate the device with Batch Configuration Tool or iVMS-4200, refer to 6.1 Activating Device Remotely. To activate the device locally, refer to 5.1 Activating Device.
Video Intercom Door Station·Quick Start Guide 5 Local Operation Key descriptions of door stations are illustrated in the table below. The number key 2 ▲ The number key 8 ▼ The number key 4 ◄ The number key 6 ► # * Call Key (When calling residents or center) Delete Return 5.1 Activating Device Steps: 1. Power on the device to enter the activation interface automatically. Figure 5-1 Activate the Device 2. Press the # key.
Video Intercom Door Station·Quick Start Guide Figure 5-2 Set Password 3. Enter a new password, and confirm the password. 4. Press the # key to complete the activation. 5.2 Editing Network Parameters Purpose: Network connection is mandatory for the use of door station. Steps: 1. Go to the configuration mode. 1) Hold down the * key and the # key for 2s to enter the admin password interface. 2) Enter the admin password, and press the # key.
Video Intercom Door Station·Quick Start Guide Figure 5-4 Network Configuration Interface 2) Press the # key to enter the network parameters settings interface. Figure 5-5 Network Parameters Settings Interface 3. Edit network parameters. 1) Move the cursor to parameters to be configured. 2) Press the # key to enter or exit the editing mode. 4. Press the * key to exit the network configuration interface after accomplishing network parameters settings. 5.
Video Intercom Door Station·Quick Start Guide Figure 5-6 Admin Password Interface The default admin password is 888999. 2. Enter the password settings interface. 1) Press the number keys 4 and 6 to switch to the password settings interface Figure 5-7 Password Settings Interface 2) Press the # key to enter the password changing interface. Figure 5-8 Password Changing Interface 3. Enter the old password, and the new password, and confirm the new one. 1) Move the cursor to parameters to be configured.
Video Intercom Door Station·Quick Start Guide 4. Press the * key to exit the network configuration interface after changing the password. 5.4 Calling Resident You can call residents via the door station. The door station can work as main/sub door station, and outer door station, which correspond to different calling resident modes respectively. Working as Main/Sub Door Station Steps: 1. Enter the Room No.. 2. Press the # key or the key to start calling the resident.
Video Intercom Door Station·Quick Start Guide Unlocking Door by Card Before you start: Make sure the card has been issued. You can issue the card via the door station, or via iVMS-4200 client software. Please refer to User Manual for detail steps. Steps: Swipe the card on the card induction area to unlock the door. The main card does not support unlocking the door.
Video Intercom Door Station·Quick Start Guide 6 Remote Operation via Batch Configuration Software 6.1 Activating Device Remotely Purpose: You are required to activate the device first by setting a strong password for it before you can use the device. Activation via Batch Configuration Tool, and Activation via iVMS-4200 are supported. Here take activation via Batch Configuration Tool as example to introduce the device activation. Please refer to the user manual for the activation via iVMS-4200. Steps: 1.
Video Intercom Door Station·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
Video Intercom Door Station·Quick Start Guide Figure 6-4 Editing Network Parameters The default port No. is 8000. After editing the network parameters of device, you should add the devices to the device list again. 6.3 Adding Device For batch configuration tool and iVMS-4200 software, you should add device to the software so as to configure the device remotely.
Video Intercom Door Station·Quick Start Guide Figure 6-6 Login Dialog Box 3. Enter the user name and password. 4. Click the OK button to save the settings. Only devices successfully logged in will be added to the device list for configuration. If you add devices in batch, please make sure selected devices have the same user name and password. 6.3.2 Adding by IP Address Purpose: You can add the device by entering IP address. Steps: 1. Click the button to pop up the adding devices dialog box.
Video Intercom Door Station·Quick Start Guide Figure 6-8 Adding by IP Address 4. Click the OK button to add the device to the device list. You cannot add the device(s) to the device list if the user name and password are not identical. When you add devices by IP Address, IP Segment or Port No., the devices should be online devices.
Video Intercom Door Station·Quick Start Guide Appendix Installation Notice While installing the indoor station, make sure that the distance between any two devices is far enough to avoid the howling and echo. The distance between two devices is recommended to be longer than 10 meters. Here devices refer to indoor station, outdoor station and master station. Wiring Cables Cable Specification Power Cord of Door Station RVV 2*1.
Video Intercom Door Station·Quick Start Guide 38
