Video Intercom Door Station (D Series) User Manual UD02927B
Video Intercom Door Station·User Manual User Manual © 2016 Hangzhou Hikvision Digital Technology Co., Ltd. This user manual is intended for users of the models below: Series Model DS-KD8102-V DS-KD8002-VM Door Station (D Series) DS-KD6002-VM DS-KD8402-VM It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection.
Video Intercom Door Station·User Manual OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. Support Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Door Station·User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Door Station·User Manual 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.
Video Intercom Door Station·User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Video Intercom Door Station·User Manual Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Video Intercom Door Station·User Manual Table of Contents 1 Overview ...................................................................................................... 1 1.1 Introduction ............................................................................................................. 1 1.2 Main Features .......................................................................................................... 1 2 Appearance ...................................................................
Video Intercom Door Station·User Manual 7.3.6 About .............................................................................................................. 35 7.4 Calling Resident ..................................................................................................... 36 7.5 Unlocking Door ...................................................................................................... 36 8 Remote Operation via Batch Configuration Tool .........................................
Video Intercom Door Station·User Manual 1 Overview 1.1 Introduction The video intercom system can realize functions such as video intercom, resident-to-resident video call, live view of HD video, access control, one-card system, elevator linkage, 8-ch zone alarm, notice information and visitor messages to provide a complete smart community video intercom solution. The video intercom door station is mainly applied to situations such as community, villa, and official buildings. 1.
Video Intercom Door Station·User Manual 2 Appearance 2.1 Appearance of DS-KD8102-V Figure 2-1 Front View Figure 2-2 Side View Table 2-1 Descriptions of Keys No.
Video Intercom Door Station·User Manual 9 IR Emission 10 IR Receiver 11 Loudspeaker 12 TAMPER 2.2 Appearance of DS-KD8002-VM 10 Figure 2-3 Front View Figure 2-4 Side View Table 2-2 Descriptions of Keys No.
Video Intercom Door Station·User Manual 7 Call Button 8 Microphone 9 Call Center Key 10 TAMPER 2.3 Appearance of DS-KD6002-VM Figure 2-5 Front View Figure 2-6 Rear View Table 2-3 Descriptions Keys No.
Video Intercom Door Station·User Manual No.
Video Intercom Door Station·User Manual 3 Typical Application Building PC Client Indoor Extension 2 App Indoor Extension 2 4F Resident 2 Resident 1 3F Video/Audio Distributor Resident 2 Center Master Station Resident 1 2F LAN Resident 2 Resident 1 1F Video/Audio Distributor Resident 2 Master Station In Guard's Room Resident 1 Network Cable Optical Fiber RS-485 Wi-Fi One Resident Card Reader Card Reader Door Station Outer Door Station Figure 3-1 Typical Application of Door Station 6
Video Intercom Door Station·User Manual 4 Terminals and Interfaces 4.1 Terminals and Interfaces of DS-KD8102-V/ DS-KD8002-VM Figure 4-1 Terminals and Interfaces of DS-KD8102-V/DS-KD8002-VM Table 4-1 Descriptions of Terminals and Interfaces Name No.
Video Intercom Door Station·User Manual Name ALARM OUT ALARM IN DOOR RS485 SENSOR No.
Video Intercom Door Station·User Manual 4.2 Terminals and Interfaces of DS-KD6002-VM Figure 4-2 Terminals and Interfaces of DS-KD6002-VM Table 4-2 Descriptions of Terminals and Interfaces Name No.
Video Intercom Door Station·User Manual Name ALARM OUT DEBUG DOOR RS485 ALARM IN No. Interface Description B1 AO2- B2 AO2+ B3 AO1- B4 AO1+ B5 GND Grounding B6 RX Serial Port Debugging/Receive data B7 TX Serial Port Debugging/Send data B8 3.
Video Intercom Door Station·User Manual 5 Installation and Wiring Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station. Make sure all the related equipment is power-off during the installation. Check the product specification for the installation environment. 5.
Video Intercom Door Station·User Manual The dimension of gang box for model DS-KD8102-V door station is: 404 (length)×123 (width)×47.5 (depth) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. 5.1.2 Wall Mounting with Gang Box of DS-KD8102-V Steps: 1. Chisel a hole in the wall for inserting the gang box. The size of the hole should be larger than that of the gang box. The suggested size of hole is 404.5 (length) × 123.
Video Intercom Door Station·User Manual Figure 5-4 Install the Door Station 5. Pull the door station downward and then push it towards the inside to make sure it fits the hole. 6. Tighten the screws of the door station with the Allen wrench.
Video Intercom Door Station·User Manual 5.2 Installation of DS-KD8002-VM 5.2.1 Gang Box for DS-KD8002-VM 135 407.5 7.6 Figure 5-6 Front View 9 9 Figure 5-7 Overhead (Plan) View The dimension of gang box for model DS-KD8002-VM door station is: 407.5 mm × 135 mm × 55 mm. The dimensions above are for reference only. The actual size can be slightly larger than the theoretical dimension. 5.2.2 Wall Mounting with Gang Box of DS-KD8002-VM 1. Chisel a hole in the wall for inserting the gang box.
Video Intercom Door Station·User Manual 8.75 118 8.75 408 384 135.5 55 Figure 5-8 Dimensions of the Hole 2. Insert the gang box into the hole and fix it with 4 PA4 screws. Figure 5-9 Insert the Gang Box into the Wall 3. Make sure the edges of the gang box align to the wall and the hook A and hook B of the gang box hook onto the wall. 4. Route the cables of the door station through the cable hole. 5.
Video Intercom Door Station·User Manual Figure 5-10 Install the Door Station 7. After fixing the door station onto the gang box, secure it by inserting the plate and insert 2 POM2 screws.
Video Intercom Door Station·User Manual 5.3 Installation of DS-KD6002-VM 5.3.1 Gang Box for DS-KD6002-VM Figure 5-12 Front and Side View The dimension of gang box for model DS-KD6002-VM door station is: 343(length)× 113(width)×55(depth) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. 5.3.2 Wall Mounting with Gang Box of DS-KD6002-VM Steps: 1. Chisel a hole in the wall for inserting the gang box.
Video Intercom Door Station·User Manual Screw Screw Figure 5-13 Insert the Gang Box into the Wall 3. Make sure the edges of the gang box align to the wall. 4. Route the cables of the door station through the cable hole. 5. Put the door station into the gang box. Figure 5-14 Install the Door Station 6. Fix the door station to the gang box with 4 crews.
Video Intercom Door Station·User Manual Figure 5-15 Tighten the Screws of Device 5.4 Wiring Description 5.4.1 Door Lock Wiring Figure 5-16 Door Lock Wiring Terminal NO1/COM1 is set as default for accessing magnetic lock/electric bolt; terminal NC1/COM1 is set as default for accessing electric strike.
Video Intercom Door Station·User Manual To connect electric lock in terminal NO2/COM2/NC2, it is required to set the output of terminal NO2/COM2/NC2 to be electric lock with Batch Configuration Tool or iVMS-4200. 5.4.2 Door Magnetic Wiring Door Magnetic Wiring for DS-KD8102-V/DS-KD8002-VM For DS-KD8102-V/DS-KD8002-VM, there are two optional ways of door magnetic wiring.
Video Intercom Door Station·User Manual Terminal S2 is set as default for connecting door magnetic. Door Magnetic Wiring for DS-KD6002-VM Figure 5-19 Door Magnetic Wiring for DS-KD6002-VM To connect the door magnetic, it is required to set the output of terminal AI2 to be door magnetic with Batch Configuration Tool or iVMS-4200. 5.4.3 Exit Button Wiring Exit Button Wiring for DS-KD8102-V/DS-KD8002-VM For DS-KD8102-V/DS-KD8002-VM, there are two optional ways of exit button wiring.
Video Intercom Door Station·User Manual To connect the exit button, it is required to set the output of terminal AI1 to be exit button with Batch Configuration Tool or iVMS-4200. Figure 5-21 Exit Button Wiring for DS-KD8102-V/DS-KD8002-VM (2) Exit Button Wiring for DS-KD6002-VM Figure 5-22 Exit Button Wiring for DS-KD6002-VM Terminal S1 is set as default for connecting exit button.
Video Intercom Door Station·User Manual 5.4.4 External Card Reader Wiring Please set the DIP switch first before connecting the card reader. If the DIP switch should be configured when the card reader is power-on, please reboot the card reader after configuring the DIP switch. The DIP switch description is shown in the following table: No.
Video Intercom Door Station·User Manual Wiegand Card Reader Wiring Figure 5-24 External Card Reader Wiring 5.4.
Video Intercom Door Station·User Manual Alarm Device Input Wiring for DS-KD6002-VM Figure 5-26 Alarm Device Input Wiring for DS-KD6002-VM 5.4.
Video Intercom Door Station·User Manual Alarm Device Output Wiring for DS-KD6002-VM Figure 5-28 Alarm Device Output Wiring for DS-KD6002-VM 26
Video Intercom Door Station·User Manual 6 Before You Start For the first time use of the device, you are required to activate the device and set the device password. You can activate the device via internet with Batch Configuration Tool, or with iVMS-4200 client software. To activate the device with Batch Configuration Tool or iVMS-4200, refer to 8 Remote Operation via Batch Configuration Tool or 9 Remote Operation via iVMS-4200 Client Software. To activate the device locally, refer to 7 Local Operation.
Video Intercom Door Station·User Manual 7 Local Operation Key descriptions of door stations are illustrated in the table below. The number key 2 ▲ The number key 8 ▼ The number key 4 ◄ The number key 6 ► # * Call Key (When calling residents or center) Confirm Return Delete 7.1 Activating Device Steps: 1. Power on the device to enter the activation interface automatically. Figure 7-1 Activate the Device 2. Press the # key.
Video Intercom Door Station·User Manual Figure 7-2 Set Password 3. Enter a new password, and confirm the password. 4. Press the # key to complete the activation. 7.2 Status Icon Description Please check the network cable of the door station. Invalid SIP server IP address. Set the SIP server IP address. Network of SIP server is not available. Check the SIP server network connection. SIP server communication is not available. Check if the SIP server IP address is correct.
Video Intercom Door Station·User Manual 7.3 Setting Parameters You can set the network configuration, local settings, password and volume of the door station. You can also view the version of the device and issue cards with it. To set parameters for the door station, you should go to the configuration mode first. Steps: 1. Hold down the * key and the # key for 2s to enter the admin password interface. 2. Enter the admin password, and press the # key.
Video Intercom Door Station·User Manual Figure 7-5 Local Parameters Settings Interface (Door Station) Figure 7-6 Local Parameters Settings Interface (Outer Door Station) 2. Edit local parameters. 1) Move the cursor to parameters to be configured. 2) Press the # key to enter or exit the editing mode. 3. Press the * key to exit the network configuration interface after accomplishing local parameters settings. In the main/sub door station mode, the serial No.
Video Intercom Door Station·User Manual Figure 7-7 Network Configuration Interface 2) Press the # key to enter the network parameters settings interface. Figure 7-8 Network Parameters Settings Interface 2. Edit network parameters. 1) Move the cursor to parameters to be configured. 2) Press the # key to enter or exit the editing mode. 3. Press the * key to exit the network configuration interface after accomplishing network parameters settings. 7.3.
Video Intercom Door Station·User Manual Figure 7-9 Password Settings Interface 2) Press the # key to enter the password changing interface. Figure 7-10 Password Changing Interface 2. Enter the old password, and the new password, and confirm the new one. 1) Move the cursor to parameters to be configured. 2) Press the # key to enter or exit the editing mode. 3. Press the * key to exit the network configuration interface after changing the password. 7.3.
Video Intercom Door Station·User Manual Figure 7-11 Card Issuing Interface 2) Press the # key to enter the main card swiping interface. 2. Swipe the main card in the card induction area, and it produces a voice prompt: Issuing card succeeded. 3. Swipe the unauthorized sub cards in turn after hearing a voice prompt: Please swipe the sub card. 4. Press the * key to exit the card issuing interface. If the main card is invalid, it prompts the message: Incorrect Main Card.
Video Intercom Door Station·User Manual Figure 7-12 Volume Settings Interface 2) Press the # key to enter the volume parameters settings interface. Figure 7-13 Volume Parameters Settings Interface 2. Set the volume. 1) Move the cursor to parameters to be configured. 2) Press the # key to enter or exit the editing mode. 3. Press the * key to exit the volume settings interface. 7.3.
Video Intercom Door Station·User Manual 7.4 Calling Resident You can call residents via the door station. The door station can work as main/sub door station, and outer door station, which correspond to different calling resident modes respectively. Working as Main/Sub Door Station Steps: 1. Enter the Room No.. 2. Press the # key or the key to start calling the resident. Working as Outer Door Station Steps: 1. Enter the Community No. and the # key, the Building No. and the # key, the Unit No.
Video Intercom Door Station·User Manual Swipe the card on the card induction area to unlock the door. The main card does not support unlocking the door.
Video Intercom Door Station·User Manual 8 Remote Operation via Batch Configuration Tool You can configure and operate the video intercom devices via Batch Configuration Tool. Default parameters of door station are as follows: Default IP Address: 192.0.0.65. Default Port No.: 8000. Default User Name: admin. 8.1 Activating Device Remotely Purpose You are required to activate the device first by setting a strong password for it before you can use the device.
Video Intercom Door Station·User Manual 3. Create a password, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
Video Intercom Door Station·User Manual Figure 8-4 Editing Network Parameters The default port No. is 8000. The default IP address of the door station is 192.0.0.65. After editing the network parameters of device, you should add the devices to the device list again. Enable DHCP, and the software can obtain network parameters for the device automatically. 8.3 Adding Device Before you start: Make sure the device to be added has been activated.
Video Intercom Door Station·User Manual Figure 8-5 Online Devices Interface 2. Click the button to pop up the login dialog box. Figure 8-6 Login Dialog Box 3. Enter the user name and password. 4. Click the OK button to save the settings. Only devices successfully logged in will be added to the device list for configuration. If you add devices in batch, please make sure selected devices have the same user name and password. 8.3.
Video Intercom Door Station·User Manual Figure 8-8 Adding by IP Address 4. Click the OK button to add the device to the device list. You cannot add the device(s) to the device list if the user name and password are not identical. When you add devices by IP Address, IP Segment or Port No., the devices should be online devices. 8.3.3 Adding by IP Segment Purpose: You can add many devices at once whose IP addresses are among the IP segment. Steps: 1.
Video Intercom Door Station·User Manual Figure 8-10 Adding by IP Segment 5. Click the OK button to search and add the devices whose IP addresses are within the range of the defined IP segment to the device list. 8.4 Configuring Devices Remotely In the device list area, select a device and click the remote configuration interface. or to enter Figure 8-11 Remote Configuration 8.4.
Video Intercom Door Station·User Manual General Click the General button to enter device general parameters settings interface. You can view and edit the device name and device ID. Figure 8-13 General Time Steps: 1. Click the Time button to enter the device time settings interface. Figure 8-14 Time Settings 2. Select Time Zone or Enable NTP. Time Zone 1) Select a time zone from the drop-down list menu. 2) Click the Synchronization button. NTP 1) Check the checkbox of Enable NTP to enable NTP.
Video Intercom Door Station·User Manual The default port No. is 123. System Maintenance Purpose: You can operate the system management and remote upgrading on the system maintenance interface. Steps: 1. Click the System Maintenance button to enter the system maintenance interface. Figure 8-15 System Maintenance 2. Click Reboot and the system reboot dialog box pops up. Click Yes to reboot the system. 3. Click Restore Default Settings to restore the default parameters. 4.
Video Intercom Door Station·User Manual Figure 8-16 Import File 6. Click Export Configuration File and the export file window pops up. Select the saving path of remote configuration files and click Save to export the configuration file. Figure 8-17 Export File 7. Click to select the upgrade file and click Upgrade to remote upgrade the device. The process of remote upgrade will be displayed in the process bar.
Video Intercom Door Station·User Manual Click Restore Default Settings button, all default settings, excluding network parameters, will be restored. Click Restore All button, all default settings, including network parameters, will be restored. The device will be reset to inactivated status. User Purpose: You can edit the password for logging in the device. Steps: 1. Click the User button to enter the user information editing interface. Figure 8-19 Select User Name 2.
Video Intercom Door Station·User Manual After editing the password of device, click button from the device list, the added device will not be there. You should add the device again with new password to operate the remote configuration. RS485 Click the RS485 button to enter the RS485 setting interface. You can view and edit the RS485 parameters of the device.
Video Intercom Door Station·User Manual 2. Select the device type from the drop-down list, and set the corresponding information. 3. Click the Save button to enable the device number configuration. For main door station (D series or V series), the serial No. is 0. For sub door station (D series or V series), the serial No. is higher than 0. Serial No. ranges from 1 to 99.
Video Intercom Door Station·User Manual Figure 8-25 Password Configuration Access Control and Elevator Step: 1. Click the Access Control and Elevator button to enter password changing interface. Figure 8-26 Access Control and Elevator Configuration 2. Set corresponding parameters on the access control and elevator settings interface. Access Control 1) Select the door No. 2) Set the door-unlocked duration.
Video Intercom Door Station·User Manual 3) 4) (Optional) Enable the function of Delay Door Alarm. Click the Save button to enable the settings. Enabling Card Encrypt, the door station can recognize the encrypted information of the card when you swiping the card on the door station. Elevator Control 1) Select the elevator No., interface, RS485 protocol. 2) Select Yes/No of the elevator linkage. 3) Enter the server IP address and server port No.. 3. Click the Save button to enable the settings.
Video Intercom Door Station·User Manual Volume Input and Output Step: 1. Click Volume Input/Output button to enter the volume input and output interface. Figure 8-28 Volume Configuration 2. Slide the slider to adjust the volume input and volume output. 3. Click the Save button to enable the settings. 8.4.3 Network Local Network Configuration Steps: 1. Click the Local Network Configuration button to enter local network configuration interface. Figure 8-29 Local Network Parameters 2.
Video Intercom Door Station·User Manual The devices can be linked to the door station and realize the linkage between these devices. Steps: 1. Click the Linked Network Configuration button to enter linked network configuration interface. Figure 8-30 Linked Network Configuration 2. Enter the master station IP address, (main) door station IP address, SIP server IP address, management center IP address, and doorphone IP address. 3. Select the main door station type from the drop-down list. 4.
Video Intercom Door Station·User Manual Figure 8-31 FTP Configuration 2. Check the checkbox of Enable Main FTP. 3. Select IP address from the drop-down list of server mode. 4. Enter the FTP server address, and port No.. 5. Check the checkbox to enable the anonymity (optional). 6. Enter the name and password. 7. Select the directory structure and set the separator, naming item, and naming element. 8. Click the Save button to enable the FTP parameters settings. The default port No. is 21.
Video Intercom Door Station·User Manual Figure 8-32 Video Display 2. Select the camera No.. 3. Select the video standard (PAL and NTSC can be selected). 4. Set the brightness, contrast, and saturation of the video. 5. Click the Save button to enable the settings. Click the Restore Default Settings button to restore all parameters excluding network parameters to the factory settings. 8.
Video Intercom Door Station·User Manual 8.5.1 Setting a Community Structure Set a community structure in the video intercom device set-up tool first, based on the real community situation, and then assign devices to the community accordingly. Figure 8-34 Setting a Community Structure 8.5.2 Setting Main/Sub Door Station Setting Main Door Station Purpose: You can activate the online main door station, and configure the building No. for the online main door station. Steps: 1.
Video Intercom Door Station·User Manual Figure 8-35 Setting Main Door Station 2. Select the door station type from the drop-down list menu: Door Station for Unit, or Door Station for Villa. 3. Enter the main door station start IP address, set the main door station floor No., and then click the Calculate button to generate the main door station end IP address and main door station No. (like 1-1-1) automatically. 4.
Video Intercom Door Station·User Manual Setting Sub Door Station Steps: 1. Select the community, and press the Sub Door Station tab to switch to the sub door station configuration interface. Figure 8-36 Setting Sub Door Station 2. Select the door station type from the drop-down list menu: Door Station for Unit, or Door Station for Villa. 3. Set the sub door station parameters (sub door station amount, floor No.
Video Intercom Door Station·User Manual Up to 8 sub door stations can be added to a main door station. For the login password, if the sub door station has been activated, enter the activation password here. If the sub door station is not activated, create a login password here, and the sub door station will be activated simultaneously. When the device is successfully configured, it prompts the note: Configuring main door station parameters succeeded 8.
Video Intercom Door Station·User Manual Figure 8-38 Login 2. Select a device, enter the user name and password, and click the Login Device button. 3. Click the Add Device button, and the device is added to the batch upgrading tool.
Video Intercom Door Station·User Manual Adding by IP Address/IP Segment Steps: 1. Click the Manual button to open the device adding window. 2. Enter the corresponding information (IP address, user name, password, start IP address, end IP address). 3. Click the Add button. Figure 8-40 Adding by IP Address/IP Segment 8.6.2 Upgrading Devices There are 2 upgrading modes available: upgrading by file, and online upgrading.
Video Intercom Door Station·User Manual Figure 8-41 Upgrade by File 3. Open the upgrading file, and click the Upgrade button. Online Upgrading Online Upgrading: The batch upgrading tool will search the latest upgrading file for the device automatically. You upgrade the device or devices via the local upgrade files. Steps: 1. Select a device or multiple devices, and select “Online Upgrading” as the upgrading mode. 2. Click the Download button.
Video Intercom Door Station·User Manual 9 Remote Operation via iVMS-4200 Client Software The Video Intercom module provides remote control and configuration on video intercom products via the iVMS-4200 client software. Before remote configure and control the video intercom, you are required to add the device to the software first. Refer to 9.2 Device Management. For remote configuration of video intercom device via the iVMS-4200 client software, refer to 9.3 Configuring Devices Remotely via iVMS-4200.
Video Intercom Door Station·User Manual Figure 9-1 System Configuration Interface 9.2 Device Management Purpose: Device management includes device activation, adding device, editing device, and deleting device, and so on. After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 9.2.
Video Intercom Door Station·User Manual 1. Click the icon on the control panel, or click Tools->Device Management to open the Device Management page. 2. Click the Server tab. To add indoor station or master station: 1) Click Add New Device Type to enter add new device type interface. Select Indoor Station/Master Station and click OK. Figure 9-2 Adding New Device Type 2) In the Server tab, Video Intercom Device will display, select Video Intercom Device and add indoor station and master station.
Video Intercom Door Station·User Manual 4. Select the devices to be added from the list. 5. Click Add to Client to open the device adding dialog box. 6. Input the required information. Nickname: Edit a name for the device as you want. Address: Input the device’s IP address. The IP address of the device is obtained automatically in this adding mode. Port: Input the device port No.. The default value is 8000. User Name: Input the device user name. By default, the user name is admin.
Video Intercom Door Station·User Manual If you want to add multiple online devices to the client software, click and hold Ctrl key to select multiple devices, and click Add to Client to open the device adding dialog box. In the pop-up message box, enter the user name and password for the devices to be added. Add All the Online Devices If you want to add all the online devices to the client software, click Add All and click OK in the pop-up message box.
Video Intercom Door Station·User Manual If the window with import file button, key importing mode drop-down list, password and confirm password field pops up, follow the steps below to reset the password: This option is available to door stations. Figure 9-6 Resetting Password (Option 1) 1. Click Export to save the device file on your computer. 2. Send the file to our technical engineers. 3. Our technical engineer will send you a file to you.
Video Intercom Door Station·User Manual If the window with import file and export file buttons, password and confirm password field pops up, follow the steps below to reset the password: Note: This option is available to indoor stations and master stations. Figure 9-7 Resetting Password (Option 2) 1. Click Export to save the device file on your computer. 2. Send the file to our technical engineers. 3. Click Import and select the file received from the technical engineer. 4.
Video Intercom Door Station·User Manual 9.4 Picture Storage When the video intercom device is under armed status, it will capture the picture automatically after unlocking the door. The captured picture can be uploaded and stored in the storage server. When starting the live view of door station via iVMS-4200, you can capture the live view picture. The captured picture can be uploaded and stored in the storage server. This function is only available to door stations.
Video Intercom Door Station·User Manual 4. Click Storage Server on the list to enter the Storage Server Adding interface. For adding the storage server, please refer to User Manual of iVMS-4200 (Video Intercom) V2.4.2 in the disk. 9.4.2 Formatting the HDDs The HDDs of the storage server need to be formatted for the captured picture storage. Steps: 1. Select the added storage server from the list and click Remote Config. 2. Click Storage->General to enter the HDD Formatting interface. 3.
Video Intercom Door Station·User Manual 9.4.3 Configuring Storage Server Picture Storage Before you start: The storage server needs to be added to the client software and the HDDs need to be formatted for the captured pictures storage. Steps: 1. Open the Record Schedule page. 2. Select the camera from the Camera Group list. 3. Select the storage server from the Storage Server drop-down list. You can click Storage Server Management to add, edit or delete the storage server. 4.
Video Intercom Door Station·User Manual Figure 9-11 Setting Quota Example: If you set the picture quota as 60%, then the 60% of the storage space can be used for storing the captured pictures. 6. Click Save to save the settings. 9.5 Live View Steps: 1. Enter the main view interface of iVMS-4200 client software to display the live view of door station.
Video Intercom Door Station·User Manual Figure 9-12 Live View of Doo Station (D Series) 2. Right click on the live view interface to display the menu and select Unlock to remote unlock the door.
Video Intercom Door Station·User Manual 9.6 Video Intercom Configuration Click the icon on the control panel of iVMS-4200 or click View -> Video Intercom to open the Video Intercom page. On the Video Intercom page, you can control video intercom devices remotely. There are 4 modules on the Video Intercom page: Video Intercom: Start visual communication with door stations, and manage incoming calls from indoor stations and door stations and master stations. Refer 9.6.2 Video Intercom for detail steps.
Video Intercom Door Station·User Manual 9.6.1 Group Management Purpose: You can add groups to community, outer door station, or other, and assign devices to each group. Enter Control Panel -> Video Intercom -> Group Management to add, edit, and delete groups. Three group types can be selected: community, outer door station and other. Adding Group 1. Click the Group Management tab to enter the group management interface. Figure 9-15 Adding Group 2.
Video Intercom Door Station·User Manual Figure 9-16 Adding Community Select Outer Door Station as group type, and then input the outer door station No. (Range: 1 to 9) to set the outer door station, as shown in the figure below. Figure 9-17 Adding Outer Door Station Select Other as group type, and then input the group name.
Video Intercom Door Station·User Manual Figure 9-18 Adding Other For example: You can name the group as administrator, entrance guard and cleaning staff, etc. When selecting Other as the group type, you can set different groups for staff other than residents, such as administrator, security guard and cleaning staff, etc., and you can assign cards to these staff and configure different permissions to them. 3. Click OK to complete group adding.
Video Intercom Door Station·User Manual Figure 9-19 Adding Resident 2. Check the checkbox of device. Indoor Station: set a Room No. for the indoor station. Door Station: set a No. for the door station. 3. Click OK to save the settings. Assigning Analog Devices to Group When assigning analog devices to group, only analog indoor stations are supported. 1. Click Add Analog to pop up analog device adding window. You can add analog devices singly or in batch.
Video Intercom Door Station·User Manual Figure 9-20 Adding Devices in Batch Room Numbers here refers to the room numbers in each floor. Adding Devices Singlly: Enter the room No.. Figure 9-21 Adding Device Singly The room No. format is like 101. 2. Click OK to save the settings. Modifying Device Information 1. Select an added device. 2. Click Modify to enter the device modifying interface.
Video Intercom Door Station·User Manual Figure 9-22 Modifying Device Information 3. Click OK to complete the device modifying operation. Deleting Device 1. Select an added device. 2. Click Remove to pop up a dialog box. Figure 9-23 Information 3. Click OK to complete the group deleting operation. 9.6.2 Video Intercom Receiving Call from Door Station Purpose: When the door station has been added to the client software, you can call iVMS-4200 via door station.
Video Intercom Door Station·User Manual Figure 9-24 Calling from Door Station When the SIP server IP of the door station is configured, press Calling Center key on the door station to call the master station instead of iVMS-4200. Click Unlock to unlock the building or villa door via iVMS-4200, no matter whether answering the call from door station or not. Click Answer to answer the call from door station. Click Hang Up to end the call from door station.
Video Intercom Door Station·User Manual For example, if there are 3 residents living in Room 401, you can assign 3 cards to No. 401 Indoor Station. For each indoor station, you can assign multiple cards, and you can assign these cards to the door station in the same building. Note: Indoor extension does not support Card Management. Before you start: Make sure the indoor station and door station have been added to the iVMS-4200 client software.
Video Intercom Door Station·User Manual Figure 9-26 Adding Cards in Batch 2. Select card adding mode and card type. Two types of card are available. Resident Card is used by residents living in the community, and Other Card is used by visitors (guest, serviceman, etc.) in the community. If you add card in batch, please set the start card No. and the end card No.. If you add card singly, please enter the card No..
Video Intercom Door Station·User Manual Figure 9-27 Issuing Card Issuing Resident Cards Steps: 1. Select Community from the organization list (like 1-1-1) and the indoor stations of the community will be listed in the resident list.
Video Intercom Door Station·User Manual 2. Click Card Selection to pop up card selection window where unauthorized resident cards are listed. Figure 9-29 Selecting Cards 3. Check the checkboxes of the cards or enter the card No. in the filter textbox you need to assign to the indoor station, and check the checkbox of door stations, doorphones and outer door stations. Only resident cards can be assigned to indoor stations. 4. Click Issue Card to complete the card issuing operation.
Video Intercom Door Station·User Manual Figure 9-30 Displaying Card Issued After issuing resident cards to the indoor station, the card No. will also be listed in the resident list. Issuing Other Cards Steps: 1. Select Other from the group list (like Cleaning Staff).
Video Intercom Door Station·User Manual 2. Click Card Selection to pop up card selection window where unauthorized other cards are listed. Figure 9-32 Selecting Cards 3. Check the checkboxes of the cards or enter the card No. in the filter textbox you need to assign to the person, and check the checkbox of door stations, doorphones and outer door stations. 4. Click Issue Card to complete the card issuing operation.
Video Intercom Door Station·User Manual Figure 9-33 Displaying Card Issued After issuing other cards to the person, the card No. will also be listed in the resident list page. Canceling Cards When canceling cards, cards that have been issued will be reset to authorized ones. Via iVMS-4200, there are two ways to cancel the cards which have been issued. Option 1: Steps: 1. Select Community from the organization list (like 1-1-1) and the indoor stations of the community will be listed in the resident list.
Video Intercom Door Station·User Manual Figure 9-34 Card Selection Interface 2. Click Card Selection to pop up card selection window where normal cards and unauthorized resident cards are listed. Figure 9-35 Selecting Cards 3. Check the checkboxes of the cards that has been issued (normal cards). 4. Click Issue Card to complete the card canceling operation.
Video Intercom Door Station·User Manual On the card issuing interface, check the checkboxes of Room No. (for resident card) or Name (for other card), click Cancel Card to cancel all card issued to the device. Through Option 1, you can cancel card from single or certain door stations. Through Option 2, you will cancel all issued cards at a time. Normal Card Click Normal Card to display normal card list.
Video Intercom Door Station·User Manual Figure 9-37 Importing File 2. Click Export Template to export the template of the batch import file. 3. Fill in the template of the batch import file and save it. 4. Click to select the batch import file and click Open. 5. Click OK to start importing the batch import file. Batch Exporting Unauthorized Cards Steps: 1. After adding unauthorized cards, and click Batch Export. 2. Select the saving file path and click Save. 3.
Video Intercom Door Station·User Manual Figure 9-38 Call Log Interface 3. Click Export to export the call logs as an excel file. Querying Unlocking Log Steps: 1. Click Query Unlocking Logs to enter the unlocking log querying page. 2. Select the unlocking type, device type, and set the start time and end time, and click Query.
Video Intercom Door Station·User Manual Figure 9-39 Unlocking Log Interface 3. Click Export to export the unlocking logs as an excel file. 9.7 Device Arming Control Steps: 1. Select Tool->Device Arming Control to pop up device arming control window.
Video Intercom Door Station·User Manual 2. Set the arming status of the device as armed, and the alarm information will be auto uploaded to the client software when alarm occurs. Figure 9-41 Device Arming Control Figure 9-42 Alarm Events After adding the device to the client software, it will be armed automatically.
Video Intercom Door Station·User Manual Appendix Installation Notice While installing the indoor station, make sure that the distance between any two devices is far enough to avoid the howling and echo. The distance between two devices is recommended to be longer than 10 meters. Here devices refer to indoor station, outdoor station and master station. Wiring Cables Cable Specification Power Cord of Door Station RVV 2*1.
Video Intercom Door Station·User Manual 97
Video Intercom Door Station·User Manual 98
