Quick Start Guide
DS-KC001
Video Intercom Monitoring Tablet
Diagram References
ENGLISH
Appearance
Installaon
Before you begin:
Wall Mounng with Juncon Box
1
3
3.1
Base Mounng with Table Bracket
3.2
Terminal
2
Screen Microphone Debugging Port
1 2 3 4
5 6 7
Make sure the device in the package is in good condion and all the assembly parts are
included.
The power supply the monitoring tablet supports is 12 VDC. Please make sure your
power supply matches your monitoring tablet.
Make sure all the related equipment is power-off during the installaon.
Check the product specificaon for the installaon environment.
Wall mounng and base mounng are supported.
The table bracket is required to install the device on the desk.
The wall mounng plate and the juncon box are required to install the device onto
the wall. The dimension of the juncon box should be 75 mm (width) × 75 mm (length)
× 50 mm (depth).
1. Put the table bracket on the desk.
2. Route the cable through the cable hole to connect the device.
3. Hook the device to the wall table bracket ghtly by inserng the table bracket hooks
into the slots on the rear panel of the device, during which the lock catch will be locked
automacally.
1. Cave a hole in the wall.
Note: The suggested dimension of the installaon hole is 76 mm (W) × 76 mm (H) × 50 mm (D).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the device to the wall mounng plate ghtly by inserng the plate hooks into the
slots on the rear panel of the device, during which the lock catch will be locked
automacally.
Regulatory Informaon
FCC Informaon
Please take aenon that changes or modificaon not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instrucons, may cause harmful interference to
radio communicaons. However, there is no guarantee that interference will not occur in a
parcular installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Condions
This device complies with part 15 of the FCC Rules. Operaon is subject to the following
two condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operaon.
Mounng Accessories
Alarm Terminals
Network Interface
Loudspeaker
12 V OUT: 12 VDC output
AIN1: Alarm Input 1
AIN2: Alarm Input 2
AIN3: Alarm Input 3
AIN4: Alarm Input 4
AIN5: Alarm Input 5
AIN6: Alarm Input 6
AIN7: Alarm Input 7
AIN8: Alarm Input 8
GND: Grounding
Power Supply Interface
Note: The appearance of the device vary according to different model. Refers to the actual device.
UD19063B
1
2
1
3
2
4
5
6 7
3.1
3.2
● All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire
prevenon regulaons and other related regulaons in your local region.
● Please use the power adapter, which is provided by normal company. The power consumpon
cannot be less than the required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or
fire hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the
device.
● When the product is installed on wall or ceiling, the device shall be firmly fixed.
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
● If the product does not work properly, please contact your dealer or the nearest service center.
Never aempt to disassemble the device yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
● Do not drop the device or subject it to physical shock, and do not expose it to high electromag-
nesm radiaon. Avoid the equipment installaon on vibraons surface or places subject to shock
(ignorance can cause equipment damage).
● Do not place the device in extremely hot (refer to the specificaon of the device for the detailed
operang temperature), cold, dusty or damp locaons, and do not expose it to high electromagnet-
ic radiaon.
● The device cover for indoor use shall be kept from rain and moisture.
● Exposing the equipment to direct sun light, low venlaon or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfuncon however), and affecng the endurance of sensor at the same
me.
● Please use the provided glove when open up the device cover, avoid direct contact with the
device cover, because the acidic sweat of the fingers may erode the surface coang of the device
cover.
● Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do not
use alkaline detergents.
● Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you
need to return the device to the factory with the original wrapper. Transportaon without the
original wrapper may result in damage on the device and lead to addional costs.
● Improper use or replacement of the baery may result in hazard of explosion. Replace with the
same or equivalent type only. Dispose of used baeries according to the instrucons provided by
the baery manufacturer.
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the RE Direcve 2014/53/EU, the EMC Direcve
2014/30/EU, the LVD Direcve 2014/35/EU, the RoHS Direcve 2011/65/EU
2012/19/EU (WEEE direcve): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collecon points.
For more informaon see: www.recyclethis.info
2006/66/EC (baery direcve): This product contains a baery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentaon for specific baery informaon. The baery is
marked with this symbol, which may include leering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to
your supplier or to a designated collecon point. For more informaon
see:www.recyclethis.info
Safety Instruction
Cauons
Warnings
Rear Panel (without Interface)
Screw
Wall Mounng Plate Juncon Box
Wall
Lock Catch Lock Catch
Lock Catch Lock Catch
Hook
Hook
Hook
60 mm
102 mm
127 mm
100 mm
27 mm
44.5 mm
70 mm
Product Informaon
©2020 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instrucons on how to use the Product. The soware embodied in the Product is governed
by the user license agreement covering that Product.
About this Manual
This Manual is subject to domesc and internaonal copyright protecon. Hangzhou Hikvision Digital
Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be
reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior
wrien permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or
the subject of applicaons for the same by Hikvision and/or its affiliates. Other trademarks menoned
in this manual are the properes of their respecve owners. No right of license is given to use such
trademarks without express permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE
OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT
YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS
INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
Data Protecon
During the use of device, personal data will be collected, stored and processed. To protect data, the
development of Hikvision devices incorporates privacy by design principles. For example, for device
with facial recognion features, biometrics data is stored in your device with encrypon method; for
fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a
fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with the
applicable data protecon laws and regulaons, including without limitaon, conducng security
controls to safeguard personal data, such as, implemenng reasonable administrave and physical
security controls, conduct periodic reviews and assessments of the effecveness of your security
controls.
Acvate Monitoring Tablet
Geng Started
4
1. Connect to the network and tap Next.
Select the Wi-Fi and enter the password to connect.
If you have connected to the wired network, you should configure network parameters.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automacally.
2. Linked related devices and tap Next. If the device and the monitoring tablet are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No. to
link.
a. Tap the device in the list to link.
b. Tap the sengs icon to pop up the Network Sengs page.
c. Edit the network parameters of the fever screen manually or enable DHCP to get the
network parameters automacally.
d. Tap OK to enable the sengs.
3. Tap Finish to save the sengs.
1. Power on the device. It will enter the acvaon page automacally.
2. Create a password and confirm it.
3. Tap OK to acvate the monitoring tablet.
You are required to acvate the device first by seng a strong password for it before
you can use the device.
1
Quick Configuraon
2
64 mm
86 mm
122 mm
AIN8
AIN7
AIN6
AIN5
AIN4
AIN3
AIN2
AIN1
GND
12V OUT
Alarm
Input
Device
Alarm
Input
Device
AIN8
AIN7
AIN6
AIN5
AIN4
AIN3
AIN2
AIN1
GND
12V OUT
Detector
+-