User Manual

ManualsBrandsHikvision ManualsAccess Control ProductsUltra Series Wall-Mounted Face Access Terminal

100

Table Of Contents

Legal Information
Symbol Conventions
Regulatory Information
Safety Instruction
Available Models
Chapter 1 Overview
- 1.1 Overview
- 1.2 Features
Chapter 2 Appearance
Chapter 3 Installation
- 3.1 Installation Environment
- 3.2 Flush Mounting with Gang Box
- 3.3 Surface Mounting
Chapter 4 Wiring
- 4.1 Terminal Description
- 4.2 Wire Normal Device
- 4.3 Wire Secure Door Control Unit
- 4.4 Wire Fire Module
  - 4.4.1 Wiring Diagram of Door Open When Powering Off
  - 4.4.2 Wiring Diagram of Door Locked When Powering Off
Chapter 5 Activation
- 5.1 Activate via Device
- 5.2 Activate via Web Browser
- 5.3 Activate via SADP
- 5.4 Activate Device via Client Software
Chapter 6 Quick Operation
- 6.1 Select Language
- 6.2 Set Application Mode
- 6.3 Set Network Parameters
- 6.4 Link to Mobile Client
- 6.5 Set Administrator
Chapter 7 Basic Operation
- 7.1 Login
  - 7.1.1 Login by Administrator
  - 7.1.2 Login by Activation Password
- 7.2 Communication Settings
- 7.3 User Management
- 7.4 Data Management
- 7.5 Identity Authentication
  - 7.5.1 Authenticate via Single Credential
  - 7.5.2 Authenticate via Multiple Credential
- 7.6 Basic Settings
- 7.7 Set Biometric Parameters
- 7.8 Set Access Control Parameters
- 7.9 Time and Attendance Status Settings
- 7.10 System Maintenance
- 7.11 Video Intercom
Chapter 8 Operation via Web Browser
- 8.1 Login
- 8.2 Live View
- 8.3 Person Management
- 8.4 Search Event
- 8.5 Configuration
Chapter 9 Client Software Configuration
- 9.1 Configuration Flow of Client Software
- 9.2 Device Management
  - 9.2.1 Add Device
  - 9.2.2 Reset Device Password
- 9.3 Group Management
- 9.4 Person Management
- 9.5 Configure Schedule and Template
  - 9.5.1 Add Holiday
  - 9.5.2 Add Template
- 9.6 Set Access Group to Assign Access Authorization to Persons
- 9.7 Configure Advanced Functions
- 9.8 Configure Linkage Actions for Access Control
- 9.9 Door Control
  - 9.9.1 Control Door Status
  - 9.9.2 Check Real-Time Access Records
- 9.10 Event Center
- 9.11 Time and Attendance
Appendix A. Tips for Scanning Fingerprint
Appendix B. Tips When Collecting/Comparing Face Picture
Appendix C. Tips for Installation Environment
Appendix D. Dimension
Appendix E. Function Differences
Appendix F. Communication Matrix and Device Command

Peripheral Type

Select a peripheral from the drop-down list according the actual situaon. You can select from

Card Reader, Extension Module, Access Controller, or Disable.

Note

Aer the peripheral is changed and saved, the device will reboot automacally.

RS-485 Address

Set the RS-485 Address according to your actual needs.

Note

If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set

the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address

according to the door No.

Baud Rate

The baud rate when the devices are communicang via the RS-485 protocol.

Output Type

If you select Access Controller as the peripheral type, you should set the parameter. The device

will output the card No. or the employee ID to the access controller.

8.5.19 Set Wiegand Parameters

You can set the Wiegand transmission direcon.

Steps

Note

Some device models do not support this funcon. Refer to the actual products when conguraon.

1. Click Conguraon → Access Control → Wiegand Sengs .

Figure 8-14 Wiegand Page

2. Check Wiegand to enable the Wiegand funcon.

3. Set a transmission direcon.

Input

The device can connect a Wiegand card reader.

DS-K1T680 Series Face Recognion Terminal User Manual