User Manual

ManualsBrandsHikvision ManualsAccess Control ProductsUltra Series Wall-Mounted Face Access Terminal

Table Of Contents

Legal Information
Symbol Conventions
Regulatory Information
Safety Instruction
Available Models
Chapter 1 Overview
- 1.1 Overview
- 1.2 Features
Chapter 2 Appearance
Chapter 3 Installation
- 3.1 Installation Environment
- 3.2 Flush Mounting with Gang Box
- 3.3 Surface Mounting
Chapter 4 Wiring
- 4.1 Terminal Description
- 4.2 Wire Normal Device
- 4.3 Wire Secure Door Control Unit
- 4.4 Wire Fire Module
  - 4.4.1 Wiring Diagram of Door Open When Powering Off
  - 4.4.2 Wiring Diagram of Door Locked When Powering Off
Chapter 5 Activation
- 5.1 Activate via Device
- 5.2 Activate via Web Browser
- 5.3 Activate via SADP
- 5.4 Activate Device via Client Software
Chapter 6 Quick Operation
- 6.1 Select Language
- 6.2 Set Application Mode
- 6.3 Set Network Parameters
- 6.4 Link to Mobile Client
- 6.5 Set Administrator
Chapter 7 Basic Operation
- 7.1 Login
  - 7.1.1 Login by Administrator
  - 7.1.2 Login by Activation Password
- 7.2 Communication Settings
- 7.3 User Management
- 7.4 Data Management
- 7.5 Identity Authentication
  - 7.5.1 Authenticate via Single Credential
  - 7.5.2 Authenticate via Multiple Credential
- 7.6 Basic Settings
- 7.7 Set Biometric Parameters
- 7.8 Set Access Control Parameters
- 7.9 Time and Attendance Status Settings
- 7.10 System Maintenance
- 7.11 Video Intercom
Chapter 8 Operation via Web Browser
- 8.1 Login
- 8.2 Live View
- 8.3 Person Management
- 8.4 Search Event
- 8.5 Configuration
Chapter 9 Client Software Configuration
- 9.1 Configuration Flow of Client Software
- 9.2 Device Management
  - 9.2.1 Add Device
  - 9.2.2 Reset Device Password
- 9.3 Group Management
- 9.4 Person Management
- 9.5 Configure Schedule and Template
  - 9.5.1 Add Holiday
  - 9.5.2 Add Template
- 9.6 Set Access Group to Assign Access Authorization to Persons
- 9.7 Configure Advanced Functions
- 9.8 Configure Linkage Actions for Access Control
- 9.9 Door Control
  - 9.9.1 Control Door Status
  - 9.9.2 Check Real-Time Access Records
- 9.10 Event Center
- 9.11 Time and Attendance
Appendix A. Tips for Scanning Fingerprint
Appendix B. Tips When Collecting/Comparing Face Picture
Appendix C. Tips for Installation Environment
Appendix D. Dimension
Appendix E. Function Differences
Appendix F. Communication Matrix and Device Command

Chapter 3 Installaon

3.1 Installaon Environment

• Avoid backlight, direct sunlight, and indirect sunlight.

• For beer recognion, there should be light source in or near the installaon environment.

• If you have to install the device outdoors, you should install a

protecve shield (oponal) for the

device.

Note

For details about installaon environment, see Tips for Installaon Environment.

3.2 Flush Mounng with Gang Box

Steps

Note

The gang box is oponal. You should purchase it separately.

1. Remove the back sheet under the TAMPER buon by removing the 2 screws. Secure the

mounng plate on the base plate with 4 screws. Remove the sponge tage on the base plate and

secure the device on the

mounng plate with 2 screws.

Figure 3-1 Secure the Device on the mounng plate

2. Secure the decoraon plate on the base plate with 4 screws. Sck 3 waterproof membranes on

the decoraon plate as shown below. Route the cable through the cable hole of the plates, and

connect to external device's cables.

Note

The waterproof membranes is used only in the ush mounng.

DS-K1T680 Series Face Recognion Terminal User Manual