LCD Display User Manual
LCD Display User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
LCD Display User Manual INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS.
LCD Display User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
LCD Display User Manual standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: http://www.recyclethis.info .
LCD Display User Manual Preface Applicable Models This manual is applicable to the LCD displays. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
LCD Display User Manual • CAUTION: Risk of explosion if the battery is replaced by an incorrect type. • Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types). • Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.
LCD Display User Manual • Install the equipment according to the instructions in this manual. • To prevent injury, this equipment must be securely attached to the bracket in accordance with the installation instructions. • The equipment shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the equipment. • Ensure correct wiring of the terminals for connection to an AC mains supply.
LCD Display User Manual • When replacing the parts of the product, please ensure that maintenance personnel use the parts designated by the manufacturer or the parts with the same performance as the original parts, so as to avoid fire, electric shock or other damage caused by the use of unauthorized parts. • After completing service or maintenance, maintenance technicians are required to perform safety checks to ensure stable operation of the product.
LCD Display User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Introduction ........................................................................................................................... 1 1.2 Key Features ........................................................................................................................... 1 Chapter 2 Remote Control .............................
LCD Display User Manual 4.3.6 Configure Screen Parameters ...................................................................................... 20 4.4 Screen On/Off ...................................................................................................................... 21 4.4.1 Turn On/Off the Screen Manually ............................................................................... 21 4.4.2 Turn On/Off the Screen on Schedule ..............................................................
LCD Display User Manual Chapter 1 Overview 1.1 Introduction The LCD display uses industrial ultra-narrow bezel and direct-lit LED backlighting. It features ultrahigh brightness, uniform brightness, no boundary shadow, long lifespan and so on. The built-in splicing controller helps realize the self-splicing of screens from the same source signals. The LCD display has abundant interfaces to receive DVI, VGA, HDMI and other signal sources, and supports a variety of control methods. 1.
LCD Display User Manual Chapter 2 Remote Control 2.1 Remote Control Functions The following table describes the functions of the remote control. Table 2-1 Remote Control Functions Appearance Key Functions POWER Power switch. TEST Enter the aging test. INFO View system information. 0-9 Enter numbers to select the desired screen or enter the special menu such as factory menu, etc. SOURCE Switch signal sources. MENU Enter/Exit the menu. IDSEL Select the desired display(s).
LCD Display User Manual Table 2-2 Startup Wizard Settings Parameter Setting OSD Language English/中文 Picture Mode Standard/Presentation/Movie/Monitor/Text/User OSD Rotation Off/90°/180°/270° Pivot Off/90°/270° System Time Year/Month/Day/Hour/Minute Menu Settings You can press MENU on your remote control to go to the menu settings. The following table describes the settings.
LCD Display User Manual Menu Setting • Left Edge: 0 to 100 • Right Edge: 0 to 100 ID Settings • • • • Config Mode: Manual/Auto Total Rows: 1 to 15 Total Columns: 1 to 15 Auto Config: Choose to automatically configure the IDs.
LCD Display User Manual To control all screens, press IDSEL, and then press IDALL. 2.4 Virtual Remote Control You can use Remote Control in the lower left corner of the client interface to control the display(s).
LCD Display User Manual Chapter 3 Installation and Connection 3.1 Installation Notice • The LCD display must be installed or moved by two or more persons. • When moving the LCD display, ensure to grasp the grips at the rear and bottom. Do not hold the LCD screen as it may cause damage, malfunction or personal injury. • The LCD display should be mounted vertically relative to horizontal line. • Mounting the LCD display on the wall requires special technologies, which must be done by professionals.
LCD Display User Manual • If your LCD display is not working normally, especially if an unusual smell is emitted from the inside, unplug it immediately and contact your dealer. • Please note that in addition to the compensation provided by law, the company is not responsible for errors caused by customers or third parties when using the machine, and is not responsible for any other related malfunctions or damages.
LCD Display User Manual Figure 3-1 Serial Port Connection • • • • Note The length of the cable as well as the environment condition may affect the image quality. The DVI-IN interface is suggested to be used as the signal input port. When operating on the cable connections, you must turn off the main power switch and pull out the power plug. Please read the Installation Guide first. Do not confuse the input and output interface, or it may cause the device exceptions or other problems. 3.
LCD Display User Manual Clean the casing of the LCD unit • Do not use benzene, thinner or other chemical products to wipe the casing; do not spray volatile solvents such as insecticide on the casing; do not leave the casing exposed to plastic or rubber materials for a long time; do not use chemical fiber cloth, detergent or paraffin. All of the above behaviors may cause cracking, deformation and stripping of the casing. • Use a non-shrinking cloth to wipe the device casing and its remote control.
LCD Display User Manual Chapter 4 Client Configuration and Operation 4.1 Register and login Steps 1. Double click LCD Display Controller.exe in the disk to install the client according to the Install Shield Wizard. Note Recommended runtime environment of the computer: • Operating system: Windows 7/Windows 8/Windows 8.1/Windows 10 (32/64-bit) English system, and Windows 7 64-bit system recommended. • CPU: Intel Pentium 4.3.0@3.0 GHz or above, and Core i3-2100 3.1 GHz recommended.
LCD Display User Manual Note If you forgot your password, you have to uninstall the client and reinstall it. You need to reconfigure the client. 4.2 Basic Configuration 4.2.1 Configure the Serial Port After registration, Serial Port Configuration interface will pop up. You need to firstly configure the serial port of your PC to control screens. Incorrect serial port configuration may result in screen control failure.
LCD Display User Manual 4.2.2 Configure the Screen Layout After configuring the serial port, you need to configure the screen layout according to the actual connections. Steps 1. Enter Number of Rows and Number of Columns in the upper right corner of the client. Figure 4-3 Screen Layout Configuration 2. Click OK to save the screen layout. 3. Optional: Click Refresh to get the newest screen status. Note Refresh is available only when the screen number is smaller than or equal to 9.
LCD Display User Manual Steps 1. Click in the upper right corner of the client. 2. In the pop-up window, click Confirm to enter the technical page. Figure 4-4 Prompt Note Click to go back to the home page. 3. Click Manual Match → Start Matching to match the screen ID manually. Figure 4-5 Manual Match the Screen ID 4. After clicking Start Matching, the attribute code defining the screen will be displayed on the upper left corner of every physical screen.
LCD Display User Manual Note You can also match the screen ID using the remote control. Auto Match Before You Start Screen layout has been set. Steps 1. Click in the upper right corner of the client. 2. In the pop-up window, click Confirm to enter the technical page. 3. Click Auto Match. Figure 4-6 Auto Match Screen ID 4. Enter Number of Rows and Number of Columns according to the actual connections.
LCD Display User Manual 2. You can switch the signal source using the following two ways. - Right-click and select Switch Signal Source to switch signal sources. Figure 4-7 Switch Signal Sources by Right-click - Select one signal source in the drop-down list of Signal Source on the right of the client, and click OK to switch signal sources.
LCD Display User Manual Note • The types of signals sources supported vary with LCD display model. The client will obtain the types of signal sources supported from the LCD display when the serial port is connected. • If a display does not send information about signal source types to the client, the client provides only three default types for you to switch. The three types include HDMI, VGA, and DVI. 4.3.2 Join Screens Steps 1.
LCD Display User Manual Figure 4-10 After Screen Splicing After the screen splicing, multiple virtual screens are joined into one screen to display one signal source image of the screen in the upper left corner. 2. Optional: Select the joined screen, and click Split on the right of the client to split the joined screen. 4.3.3 Manage Scenes You can set and call a scene to configure screens quickly.
LCD Display User Manual Figure 4-11 Scene Management Table 4-1 Operations of Scene Management Operation Step Save a Scene After setting a scene, a prompt will pop up to remind you to save the scene before you switch to other scenes. Rename a Scene Select a scene, and click Call a Scene Select a scene, and click to call the scene. You can also double click the scene to call it as desired. Note • The client supports 8 scenes at most. • The default scene layout is 2 × 2. 4.3.
LCD Display User Manual Figure 4-12 Time Sync Settings 2. You can set the screen time in either of the following two ways. - Click to set the time and date. - Check Use Local Time to save the computer time to the screen. 3. Click Save to finish time sync. 4.3.5 View Screen Status Select one virtual screen, and hover over information.
LCD Display User Manual Table 4-2 Description of Virtual Screen Color Color Description Green The screen signal source is normal. Black The screen has no signal input. The screen is powered off. The serial port connection is abnormal. Grey The Screen status is unknown. Click Refresh to get the latest status when the screen layout is less than 3 × 3. Orange The screen temperature is too high. 4.3.6 Configure Screen Parameters Only professionals are recommended to configure screen parameters.
LCD Display User Manual Color Temperature You can configure red/green/blue gains or offsets. Backlight You can increase or decrease the brightness of screen backlight. Screen Type Different images can be selected to adjust chromatic aberration. 4.4 Screen On/Off 4.4.1 Turn On/Off the Screen Manually Before You Start The serial port has already been configured correctly. Steps 1. Select one or more screens. 2. You can turn on/off the screens in either of the following two ways.
LCD Display User Manual Figure 4-15 Startup Time Settings 3. Drag and draw green bars in the days of a week. The area in green indicates the diaplay is turned on. In other duration, the display turns off. 4. Select the green bars to precisely set the starting and ending time. 5. Repeat the operations to set the schedule of the whole week. Note • Only 2 startup periods can be set at most. • The interval between startup periods must be at least 2 minutes. 6.
LCD Display User Manual Note For some LCD display models, the startup time settings take effect only when the client is running. 4.5 Client Management 4.5.1 Lock/Unlock the Client You can lock the client to prevent others from changing the configuration. Steps 1. Click in the upper right corner to lock the client. What to do next To unlock the client, you need to enter the login password, and then click Unlock. Figure 4-16 Unlock the Client 4.5.2 Change Login Password Steps 1.
LCD Display User Manual 2. Enter the Old Password, then set a New Password and confirm. 3. Click Save to change the login password. Note You need to enter the new password when logging in next time. You need to check Save Password and Auto Login again, too. 4.5.3 Enable/Disable Auto Login Click in the upper right corner of the client, and select Enable/Disable Auto Login. Check/ Uncheck Auto Login. 4.5.
UD19076B
