Network Video Recorder Quick Start Guide UD01971B
Network Video Recorder Quick Start Guide TABLE OF CONTENTS Chapter1 Panels Description ........................................................................................................................... 7 1.1 1.2 Front Panel ...................................................................................................................................... 7 1.1.1 DS-96000NI-I16 Series ...................................................................................................... 7 1.1.
Network Video Recorder Quick Start Guide Quick Start Guide COPYRIGHT ©2016 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network Video Recorder Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Network Video Recorder Quick Start Guide Applicable Models This manual is applicable to the models listed in the following table.
Network Video Recorder Quick Start Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Provides additional information to emphasize or supplement important points of the main text.
Network Video Recorder Quick Start Guide Chapter1 Panels Description 1.1 Front Panel 1.1.1 DS-96000NI-I16 Series Figure 1. 1 DS-96000NI-I16 Series Table 1. 1 Description No. Name Description 1 Panel lock Locks or unlocks the panel by the key. Exit 2 Shortcut buttons Menu 3 Status indicator HDD Tx/Rx 4 5 Returns to the previous menu. ● Press it twice quickly to switch the main and auxiliary port. ● In live view mode, press it to enter PTZ control interface.
Network Video Recorder Quick Start Guide No. Name Description ● Advances the video by a single frame in single-frame playback mode. ● Stops/starts auto switch in auto-switch mode. ● Navigates between different fields and items in menus. ● In the playback mode, use the Up and Down buttons to speed up and slow down recorded video. Use the Left and Right buttons to select the DIRECTION 6 next and previous video files. ● Cycles through channels in live view mode.
Network Video Recorder Quick Start Guide 1.2 Rear Panel Purpose: The interfaces of DS-96000NI-I16 and DS-96000NI-I24 are the same. Here we take the example of DS-96000NI-I16 series to introduce the rear panel. Figure 1. 3 DS-96000NI-I16 Series Table 1. 3 Panel Description No. Name Description 1 HDMI 1/2 HDMI video output connector. 2 Audio in RCA connector for audio input. Audio out RCA connector for audio output. USB 3.0 Universal Serial Bus (USB 3.
Network Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 NVR Installation During installation of the NVR: 1. 2. 3. 4. 5. 6. 7. 8. Use brackets for rack mounting. Ensure ample room for audio and video cables. When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. Connect the alarm cable. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. Ensure the NVR is grounded.
Network Video Recorder Quick Start Guide Figure 2. 2 Insert Panel Key 3. Press the buttons on the panel of two sides and open the front panel. Figure 2. 3 Open Panel Lock 4. Insert the hard disk along the slot until it is placed into position. Figure 2. 4 Insert Hard Disk 5. Repeat the above steps to install other hard disks onto the NVR. After having finished the installation of all hard disks, close the front panel and lock it with the key again. Figure 2.
Network Video Recorder Quick Start Guide 2.2.2 DS-96000NI-I24 Series Purpose: The following section introduces the HDD installation for the DS-96000NI-I24 series NVR. Steps: 1. Unlock the front panel with the panel key. Figure 2. 6 Unlock the Panel 2. To remove the cover from front panel, operate following steps: 1) Slightly pull the left part of the front panel out of the device along the direction arrow ② and ensure it is a little above the handle.
Network Video Recorder Quick Start Guide 4. Fix the hard disk in the hard disk box. 1) Place a hard disk in the hard disk box. The SATA interface must face the hard disk box bottom. 2) Adjust the hard disk position. Ensure the hard disk rear aligning with hard disk bottom. 3) Use a screwdriver to fasten the four screws into the screw holes that in both sides. Figure 2. 9 Fix the Hard Disk 5. Push the hard disk box back into the slot. Figure 2. 10 Push the Hard Disk Box into the Slot 6.
Network Video Recorder Quick Start Guide Figure 2.
Network Video Recorder Quick Start Guide 2.3 Connections 2.3.1 Alarm Input Wiring The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device. Figure 2. 13 Alarm Input Wiring 2.3.2 Alarm Output Wiring To connect to an alarm output (AC or DC load), use the following diagram: Figure 2.
Network Video Recorder Quick Start Guide 2.3.3 Using Alarm Connectors To connect alarm devices to the NVR: 1. Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block. 2. Unfasten stop screws from the pluggable block, insert signal cables into slots and fasten stop screws. Ensure signal cables are tight. 3. Connect pluggable block back into terminal block. 2.3.4 Controller Connection Figure 2. 15 Controller Connection To connect a controller to the NVR: 1.
Network Video Recorder Quick Start Guide 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate 96K 128K 160K 192K 224K 256K 320K 384K 448K 512K 640K 768K 896K 1024K 1280K 1536K 1792K 2048K Storage Used 42M 56M 70M 84M 98M 112M 140M 168M 196M 225M 281M 337M 393M 450M 562M 675M 787M 900M 4096K 1.8G 8192K 3.6G 16384K 7.
Network Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.
Network Video Recorder Quick Start Guide 3.2.2 Shutdown Steps: 1. Enter the Shutdown menu. Menu > Shutdown Figure 3. 2 Shutdown 2. Select the Shutdown button. 3. Click the Yes button. 3.3 Activating Your Device Purpose: For the first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation. You can also activate the device via Web Browser, SADP or client software. Steps: 1.
Network Video Recorder Quick Start Guide For the old version device, if you upgrade it to the new version, the following dialog box will pop up once the device starts up. You can click YES and follow the wizard to set a strong password. Figure 3. 4 Warning of Weak Password 3.4 Using the Unlock Pattern for Login For the Admin user, you can configure the unlock pattern for device login. After the device is activated, you can enter the following interface to configure the device unlock pattern. Steps: 1.
Network Video Recorder Quick Start Guide 3.5 Login and Logout 3.5.1 User Login Purpose: If NVR has logged out, you must login the device before operating the menu and other functions. Steps: 1. Select the User Name in the dropdown list. Figure 3. 6 Login 2. Input Password. 3. Click OK to log in. In the Login dialog box, if you enter the wrong password 7 times, the current user account will be locked for 60 seconds. Figure 3. 7 Account Lock 3.5.
Network Video Recorder Quick Start Guide Figure 3. 8 Logout 2. Click Logout. After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system. 3.6 Using the Setup Wizard The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts once the device has loaded. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard.
Network Video Recorder Quick Start Guide Menu > Configuration > Network Figure 3. 10 Network Settings 2. Select the General tab. 3. In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server. If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP address and other network settings from that server. 4.
Network Video Recorder Quick Start Guide Figure 3. 11 Add IP Camera 3. Select the detected IP camera and click the Add button to add it directly, and you can click the Search button to refresh the online IP camera manually. Or you can choose to custom add the IP camera by editing the parameters in the corresponding text field and then click the Add button to add it. 3.9 Live View Icons are provided on screen in Live View mode to indicate camera status.
Network Video Recorder Quick Start Guide As the default array type is RAID 5, at least 3 HDDs must be installed in you device. And if more than 10 HDDs are installed, 2 arrays can be configured. Steps: 1. Enter the Physical Disk Settings interface. Menu > HDD > RAID Figure 3. 12 RAID Settings Interface 2. Click One-touch Configuration to enter the One-touch Array Configuration interface. Figure 3. 13 One-touch Array Configuration 3.
Network Video Recorder Quick Start Guide After rebooting all the manual records enabled are cancelled. Steps: 1. On the live view window, right click the window and move the cursor to the Start Recording option, and select Continuous Record or Motion Detection Record on your demand. Figure 3. 14 Start Recording from Right-click Menu 2. Click the Yes button in the pop-up Attention message box to confirm the settings. All the channels will start to record in the selected mode. 3.
Network Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. Purpose: You can get access to the device via web browser.
Network Video Recorder Quick Start Guide Figure 4. 2 Login 3. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in. After login, you can perform the operation and configuration of the device, including the live view, playback, log search, configuration, etc.
Network Video Recorder Quick Start Guide 29
