Digital Video Recorder Quick Start Guide
Digital Video Recorder Quick Start Guide Quick Start Guide COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Digital Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Digital Video Recorder Quick Start Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.
Digital Video Recorder Quick Start Guide Power Supply Instructions Use only power supplies listed below. For DS-7104HQHI-K1, DS-7108HQHI-K1, and DS-7104HUHI-K1. Standard British European Australia Power Supply Models Manufacturer MSA-C1500IC12.0-18P-GB MOSO Technology Co., Ltd. ADS-26FSG-12 12018EPB MSA-C1500IC12.0-18P-DE ADS-26FSG-12 12018EPG KPD-018F-VI,12V1.5A MSA-C1500IC12.0-18P-AU ADS-26FSG-12 12018EPSA Shenzhen Honor Electronic Co., Ltd. MOSO Technology Co., Ltd.
Digital Video Recorder Quick Start Guide Chapter 1 Rear Panel Interfaces Description The rear panel interfaces vary with different models. Refer to Table 1-1 for the common interfaces description of rear panels.
Digital Video Recorder Quick Start Guide 2.2 HDD Installation Before you start Before installing a hard disk drive (HDD), please make sure the power is disconnected from the device. A factory recommended HDD should be used for the installation. Tools Required: Cross screwdriver. 2.2.1 Bracket Installation Bracket installation is applicable when you need to remove the cover of the device and install the HDD to the internal bracket.
Digital Video Recorder Quick Start Guide 2.2.3 Fix-on-Bottom Installation Fix-on-bottom installation is applicable when you need to install and fix the HDD on the device bottom. Step 1 Remove the cover from device 2) Connect the other end of data Step 3 Set the device up, by unfastening the screws on cable to HDD. match HDD screw panels. 3) Connect one end of power cable to threads with the HDD. reserved holes on the 4) Connect the other end of power device bottom, and fix cable to the device motherboard.
Digital Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.1 Startup Proper startup is crucial to expanding the life of the DVR. Step 1 Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power button on the front panel should be red, indicating the device is receiving the power. Step 2 Press the POWER button on the front panel. The Power LED should turn blue.
Digital Video Recorder Quick Start Guide 3.3 Use the Unlock Pattern for Login Purpose For the Admin user, you can configure the unlock pattern for device login. After the device is activated, you can configure the device unlock pattern. Step 1 Use the mouse to draw a pattern among the 9 dots on the screen. Release the mouse when the pattern is done. Connect at least 4 dots to draw the pattern. Each dot can be connected for once only. Step 2 Draw the same pattern again to confirm it.
Digital Video Recorder Quick Start Guide 3.5 User Logout, Shutdown and Reboot Purpose You can log out of the system, shut down, or reboot the device. Step 1 Click on the menu bar. Step 2 Click Logout, Shutdown, or Reboot. After you have logged out of the system, menu operation on the screen is invalid. User name and password are required to unlock the system. 3.6 Configure Signal Input Purpose For some models, you can configure the analog and IP signal input types and 5 MP long distance transmission.
Digital Video Recorder Quick Start Guide 3.7 Add IP Cameras Purpose Add the network cameras to the connection list of the device before getting live video or recording videos. Before you start Ensure the network connection is valid and correct, and the IP camera to add has already been activated. Please refer to the User Manual for activating the inactive IP camera. Step 1 Click on the main menu bar. Step 2 Click Custom Add on the title bar.
Digital Video Recorder Quick Start Guide powered on and then powered off, and there is no video and “Insufficient Power for PoC” is overlaid on the live view image. If the power consumption of the DVR is higher than that of the AT camera, when AF or AT camera is connected, it is powered on normally. Step 4 Check the connected AF or AT camera number and the connectable camera number. Only Hikvision PoC camera is supported. The maximum connectable AT/AF camera number varies with different models.
Digital Video Recorder Quick Start Guide 3) Check The Hik-Connect service will require internet access. Please read Service Terms and Privacy Statement before enabling the service if you agree the service terms and privacy statement. 4) Click OK to save the settings. Hik-Connect is disabled by default. The verification code is empty by default. It must contain 6 to 12 letters or numbers, and it is case sensitive. Step 3 (Optional) Check Custom to enter the server address as your desire.
Digital Video Recorder Quick Start Guide Step 1 Enter the playback mode ( ). Step 2 Check the channel(s) in the list. Step 3 Double-click to select a date on the calendar. Step 4 You can use the toolbar in the bottom part of Playback interface to control playing progress.
Digital Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. Purpose You can get access to the device via web browser.
