User Manual
Table Of Contents
- 1.1 Product Key Features
- Chapter 1 Introduction
- Chapter 2 Getting Started
- Chapter 3 Live View
- 3.1 Introduction of Live View
- 3.2 Operations in Live View Mode
- 3.3 Channel-Zero Encoding
- 3.4 Adjusting Live View Settings
- 3.5 Manual Video Quality Diagnostics
- Chapter 4 PTZ Controls
- Chapter 5 Recording and Capture Settings
- 5.1 Configuring Encoding Parameters
- 5.2 Configuring Recording and Capture Schedule
- 5.3 Configuring Motion Detection Recording and Capture
- 5.4 Configuring Alarm Triggered Recording and Capture
- 5.5 Configuring Event Recording and Capture
- 5.6 Configuring Manual Recording and Continous Capture
- 5.7 Configuring Holiday Recording and Capture
- 5.8 Configuring Redundant Recording and Capture
- 5.9 Configuring HDD Group
- 5.10 Files Protection
- 5.11 One-Key Enabling and Disabling H.264+ for Analog Cameras
- 5.12 Configuring 1080P Lite
- Chapter 6 Playback
- 6.1 Playing Back Record Files
- 6.2 Auxiliary Functions of Playback
- Chapter 7 Backup
- Chapter 8 Alarm Settings
- Chapter 9 POS Configuration
- Chapter 10 VCA Alarm
- 10.1 Face Detection
- 10.2 Vehicle Detection
- 10.3 Line Crossing Detection
- 10.4 Intrusion Detection
- 10.5 Region Entrance Detection
- 10.6 Region Exiting Detection
- 10.7 Loitering Detection
- 10.8 People Gathering Detection
- 10.9 Fast Moving Detection
- 10.10 Parking Detection
- 10.11 Unattended Baggage Detection
- 10.12 Object Removal Detection
- 10.13 Audio Exception Detection
- 10.14 Defocus Detection
- 10.15 Sudden Scene Change
- 10.16 PIR Alarm
- Chapter 11 VCA Search
- Chapter 12 Network Settings
- Chapter 13 RAID
- Chapter 14 HDD Management
- Chapter 15 Camera Settings
- Chapter 16 DVR Management and Maintenance
- Chapter 17 Others
- Chapter 18 Appendix
- 18.1 Specifications
- 18.1.1 DS-7100HGHI-E1
- 18.1.2 DS-7200HGHI-E1
- 18.1.3 DS-7200HGHI-E2
- 18.1.4 DS-7100HGHI-F1
- 18.1.5 DS-7200HGHI-F1
- 18.1.6 DS-7200HGHI-F2
- 18.1.7 DS-7100HQHI-F1/N
- 18.1.8 DS-7200HQHI-F1/N
- 18.1.9 DS-7200HQHI-F2/N
- 18.1.10 DS-7100HGHI-F1/N
- 18.1.11 DS-7200HGHI-F1/N
- 18.1.12 DS-7200HUHI-F1/N
- 18.1.13 DS-7200HUHI-F2/N
- 18.1.14 DS-7600HUHI-F/N
- 18.1.15 DS-7300HUHI-F4/N
- 18.1.16 DS-8100HUHI-F8/N
- 18.1.17 DS-9000HUHI-F8/N
- 18.1.18 DS-9000HUHI-F16/N
- 18.1.19 DS-7300HQHI-F4/N
- 18.1.20 DS-8100HQHI-F8/N
- 18.2 Glossary
- 18.3 Troubleshooting
- 18.4 Summary of Changes
- 18.5 List of Compatible Hikvision IP Cameras
- 18.6 List of Compatible Third-Party IP Cameras
- 18.1 Specifications
Digital Video Recorder User Manual
318
If there is still no image display on the monitor after rebooting, please check if the
connection cable is good, and change a cable to connect again.
Step 3 Verify Input mode of the monitor is correct.
Please check the input mode of the monitor matches with the output mode of the device
(e.g. if the output mode of DVR is HDMI output, then the input mode of monitor must be
the HDMI input). And if not, please modify the input mode of monitor.
Step 4 Check if the fault is solved by the step 1 to step 3.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
There is a beep sound after a new bought device starts up.
Possible Reasons:
— No HDD is installed in the device.
— The installed HDD has not been initialized.
— The installed HDD is not compatible with the device or is broken-down.
Step 1 Verify at least one HDD is installed in the device.
1) If not, please install the compatible HDD.
Please refer to the “Quick Operation Guide” for the HDD installation steps.
2) If you do not want to install a HDD, select “Menu>Configuration > Exceptions”, and
uncheck the Audible Warning checkbox of “HDD Error”.
Step 2 Verify the HDD is initialized.
1) Select “Menu>HDD>General”.
2) If the status of the HDD is “Uninitialized”, please check the checkbox of corresponding
HDD and click the “Init” button.
Step 3 Verify the HDD is detected or is in good condition.
1) Select “Menu>HDD>General”.
2) If the HDD is not detected or the status is “Abnormal”, please replace the dedicated HDD
according to the requirement.
Step 4 Check if the fault is solved by the step 1 to step 3.
1) If it is solved, finish the process.
2) If not, please contact the engineer from our company to do the further process.
Live view stuck when video outputs locally.
Possible Reasons: