Digital Video Recorder DS-7204HTI-K1 DS-7208HTI-K2 User Manual
DS-720xHTI-Kx DVR User Manual Hikvision USA Inc., 18639 Railroad St., City of Industry, CA 91748, USA • Hikvision Canada, 4848 rue Levy, Saint Laurent, Quebec, Canada, H4R 2P1 Telephone: +1-909-895-0400 • Toll Free in USA: +1-866-200-6690 • E-Mail: sales.usa@hikvision.com • www.hikvision.com. © 2017-2018 Hikvision USA Inc. • All Rights Reserved • Any and all information, including, among others, wordings, pictures, and graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd.
DS-720xHTI-Kx DVR User Manual Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-720xHTI-Kx DVR User Manual • Maintenance ˗ Replace after a serious electrical event (e.g.
DS-720xHTI-Kx DVR User Manual • Supports cloud storage • S.M.A.R.T.
DS-720xHTI-Kx DVR User Manual • You can enable false alarm filer for the motion detection of the PIR cameras. Then only when the motion detection events and PIR events are both triggered, the motion detection alarm will be triggered.
DS-720xHTI-Kx DVR User Manual Table of Contents Chapter 1 Introduction......................................................................................................................................... 11 1.1 Front Panel ......................................................................................................................................... 11 1.2 IR Remote Control Operations ...........................................................................................................
DS-720xHTI-Kx DVR User Manual 4.2 Setting PTZ Presets, Patrols, and Patterns ...................................................................................... 43 4.2.1 Customizing Presets ................................................................................................................. 43 4.2.2 Calling Presets .......................................................................................................................... 44 4.2.3 Customizing Patrols ...........................
DS-720xHTI-Kx DVR User Manual 6.2.4 File Management....................................................................................................................... 88 Chapter 7 Backup ................................................................................................................................................. 90 7.1 Backing up Record Files .................................................................................................................... 90 7.1.
DS-720xHTI-Kx DVR User Manual 10.5 Heat Map ......................................................................................................................................... 130 Chapter 11 Network Settings ............................................................................................................................ 132 11.1 Configuring General Settings ........................................................................................................ 132 11.
DS-720xHTI-Kx DVR User Manual 14.1 Viewing System Information.......................................................................................................... 164 14.2 Searching Log Files........................................................................................................................ 164 14.3 Importing/Exporting IP Camera Info .............................................................................................. 166 14.4 Importing/Exporting Configuration Files ......
DS-720xHTI-Kx DVR User Manual Chapter 1 Introduction 1.1 Front Panel Figure 1-1 Front Panel Table 1-1Front Panel Description No. Icon Description 1 Turns white when DVR is powered up 2 Turns red when data is being read from or written to HDD 3 Flashes white when the network is well-connected 4 Receiver for IR remote control 5 Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB USB Interface Hard Disk Drive (HDD) 1.
DS-720xHTI-Kx DVR User Manual Figure 1-2 Remote Control The keys on the remote control closely resemble the ones found on the front panel. Refer to Table 1-2. Table 1-2 Description of the IR Remote Control Buttons No. Name Description Power on/off the device. 1 POWER Power on/off the device by pressing and holding the button for five seconds. Press to return to the main menu (after successful login). Press and hold for 5 seconds to turn off audible key beep.
DS-720xHTI-Kx DVR User Manual No. Name ENTER Button 5 6 PTZ Button DEV 7 Alphanumeric Buttons 8 ESC Button 9 PLAY Button 10 PREV Button Description In PTZ control mode, controls PTZ camera movement. Confirm selection in any menu mode. Can tick checkbox fields. In Playback mode, plays or pauses the video. In single-frame Playback mode, advances video a single frame. In Auto-switch mode, stops/starts auto switch. Enables/Disables Remote Control.
DS-720xHTI-Kx DVR User Manual 1. Plug USB mouse into one of the USB interfaces on the DVR front panel. 2. The mouse should automatically be detected. If the mouse is not detected, it may be that the two devices are not compatible. Refer to the recommended device list from your provider.
DS-720xHTI-Kx DVR User Manual 1.5 Rear Panels Figure 1-4 DS-7204HTI-K1 Rear Panel Figure 1-5 DS-7208HTI-K2 Rear Panel Table 1-5 Description of Rear Panel No. Item Description 1 VIDEO IN BNC interface for TurboHD and analog video input 2 AUDIO IN RCA connector 3 AUDIO OUT RCA connector VGA DB-15 connector for VGA output. Display local video output and menu. 4 5 HDMI HDMI video output connector.
DS-720xHTI-Kx DVR User Manual Chapter 2 Getting Started 2.1 Starting Up and Shutting Down the DVR Purpose Proper startup and shutdown procedures are crucial to expanding the life of the DVR. Before You Start Check that the voltage of the external power supply matches the DVR’s requirement, and ensure that the ground connection is working properly. Starting up the DVR 1. Check that the power supply is plugged into an electrical outlet.
DS-720xHTI-Kx DVR User Manual Figure 2-1 Shutdown Button Figure 2-2 Shutdown Menu 4. Click Yes. 5. Turn off the power switch on the rear panel when the following note appears. Figure 2-3 Shutdown Tips 2.2 Activating the Device Purpose For first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation. You can activate the device via Web browser, SADP, or Client Software. 1.
DS-720xHTI-Kx DVR User Manual Figure 2-4 Settings Admin Password STRONG PASSWORD RECOMMENDED – We highly recommend that you create a strong password of your own choosing (using a minimum of eight characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. We also recommend that you reset your password regularly.
DS-720xHTI-Kx DVR User Manual Figure 2-6 Attention 5. (Optional) Click Yes to export the GUID (Globally Unique Identifier). The Reset Password interface pops up. Click Export to export the GUID to the USB flash drive for password resetting. The GUID is a file that is generated, exported, and saved that is used to reset the user’s password. Figure 2-7 Export GUID 6. After exporting the GUID, the Attention box pops up. Click Yes to duplicate the password or No to cancel it.
DS-720xHTI-Kx DVR User Manual Figure 2-9 Set Unlock Pattern 1. Use the mouse to draw a pattern among the nine dots on the screen. Release the mouse when the pattern is done. Figure 2-10 Draw the Pattern Connect at least four dots to draw the pattern. Each dot can be connected once only. 2. Draw the same pattern again to confirm it. When the two patterns match, the pattern is successfully configured.
DS-720xHTI-Kx DVR User Manual Figure 2-11 Confirm the Pattern If the two patterns are different, you must set the pattern again. 2.3.2 Logging in via the Unlock Pattern Only the admin user has permission to unlock the device. Configure the pattern before unlocking. See 2.3.1 Configuring the Unlock Pattern. Right click the mouse on the screen and select the menu to enter the interface. Figure 2-12 Draw the Unlock Pattern 1. Draw the pre-defined pattern to unlock to enter the menu operation.
DS-720xHTI-Kx DVR User Manual Right click the mouse to log in via the normal mode. If you forgot your pattern, click Forgot My Pattern or Switch User to display the normal login dialog box. If the pattern you draw differs from the pattern you configured, try again. If you draw the wrong pattern seven times, the account will lock for one minute. Figure 2-13 Normal Login Dialog Box 2.4 Login and Logout 2.4.
DS-720xHTI-Kx DVR User Manual In the Login interface, for the admin, if you enter the wrong password seven times, the account will lock for 60 seconds. For an operator, if you enter the wrong password five times, the account will lock for 60 seconds. Figure 2-15 User Account Protection for the Admin Figure 2-16 User Account Protection for the Operator 2.4.2 User Logout Purpose You can log out of the system, shut down, or reboot the device upon demand. 1. Go to Menu > System Maintenance. 2.
DS-720xHTI-Kx DVR User Manual 2.5 Resetting Your Password Purpose When you forget the password of the admin, you can reset the password by importing the GUID file. The GUID file must be exported and saved in the local USB flash drive after you have activated the device (refer to Activating the Device 2.2 ). 1. On the user login interface, click Forgot Password to enter the Import GUID interface. Figure 2-18 Import GUID 2.
DS-720xHTI-Kx DVR User Manual Figure 2-20 GUID File Imported 5. Click OK and the Attention box below pops up to remind you to duplicate the device password to connected IP cameras with default protocol. Click Yes to duplicate the password or No to cancel it. Figure 2-21 Duplicate the Password To retrieve a forgotten password, you must first export the GUID file. Once the password is reset, the GUID file will be invalid. You can export a new GUID file. Refer to Editing a User 15.4.3 . 2.
DS-720xHTI-Kx DVR User Manual Figure 2-22 IP Camera Management Interface 2. Click the camera’s inactive icon to enter the following interface to activate it. You can also select multiple cameras from the list and click the One-touch Activate to activate the cameras in batch. Figure 2-23 Activate the Camera 3. Set the password of the camera to activate it. • Use Admin Password: When checked, the camera(s) will use the DVR’s admin password.
DS-720xHTI-Kx DVR User Manual STRONG PASSWORD RECOMMENDED – We highly recommend that you create a strong password of your own choosing (using a minimum of eight characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. We also recommend that you reset your password regularly.
DS-720xHTI-Kx DVR User Manual Figure 2-26 Select Multiple Channels OPTION 2: 1. On the IP Camera Management interface, click Custom Adding to show Add IP Camera (Custom). Figure 2-27 Custom Adding IP Camera Interface 2. Edit the IP address, protocol, management port, and other information of the camera to be added. If the IP camera to add has not been activated, activate it from the IP camera list on the IP Camera Management interface. 3. Click Add to add the camera.
DS-720xHTI-Kx DVR User Manual Table 1-6 Explanation of the Icons Icon Explanation Icon Edit basic parameters of the camera Add the detected IP camera. The camera is disconnected; you can click the icon to get the exception information of camera. Play the live video of the connected camera. Upgrade the connected IP camera. Explanation Delete the IP camera Advanced settings of the camera.
DS-720xHTI-Kx DVR User Manual Figure 2-29 Camera Network Configuration 3. You can edit the camera’s network information and password. Figure 2-30 Camera Password Configuration 4. Click OK to save the settings and exit the interface. 2.8 Configuring 5 MP Long Distance Transmission Purpose You can configure 5 MP long distance transmission on the Signal Input Status interface. 1. Go to Menu > Camera Setup > Signal Input Status. Figure 2-31 Signal Input Status 2.
DS-720xHTI-Kx DVR User Manual Figure 2-32 5 MP Long Distance Transmission Settings 3. Check the checkbox to enable 5 MP Long Distance Transmission of the selected channel. 4. Click Apply to save the settings.
DS-720xHTI-Kx DVR User Manual Chapter 3 Live View 3.1 Introduction of Live View Live view shows the video image from each camera in real time. The DVR will automatically enter Live View mode when powered on. It is also at the very top of the menu hierarchy, thus hitting ESC many times (depending on which menu you’re on) will bring you to the Live View mode.
DS-720xHTI-Kx DVR User Manual Table 1-8 Priorities of Outputs in Independent Output Mode S.N HDMI VGA CVBS Main Output Auxiliary Output 1 √ √ √ or × HDMI VGA 2 √ or × × √ or × HDMI CVBS 3 × √ √ or × VGA CVBS For Live View Output Only CVBS VGA HDMI √ means the interface is in use, × means the interface is out of use or the connection is invalid. HDMI, VGA, and CVBS can be used at the same time. 3.2.
DS-720xHTI-Kx DVR User Manual 3.2.2 Quick Setting Toolbar in Live View Mode On the screen of each channel, there is a quick setting toolbar which shows when you click the screen.
DS-720xHTI-Kx DVR User Manual Figure 3-4 Image Settings Face Detection can be enabled if you click the icon. The dialog pops up as shown in Figure 3-6. Click Yes and the full-screen live view of the channel is enabled. Click to exit from the full-screen mode. Figure 3-5 Enable Face Detection You can configure face detection only when it is supported by the connected camera.
DS-720xHTI-Kx DVR User Manual Figure 3-7 Enable VCA Information Overlay In the live view, only the analog cameras support VCA information overlay. Enable VCA function first before showing the VCA information. Refer to Chapter 9 VCA Alarm for detailed operation. The VCA information is hidden by default. If the connected analog camera does not support VCA, the icon displays grey and cannot be operated. For the analog cameras, the VCA information includes line crossing detection and intrusion detection.
DS-720xHTI-Kx DVR User Manual Figure 3-8 Live View Channel-Zero Encoding 2. Check the checkbox after Enable Channel-Zero Encoding. 3. Configure the Frame Rate, Max. Bitrate Mode and Max. Bitrate. 4. Click Apply to activate the settings. 5. After you set the Channel-Zero encoding, you can get a view in the remote client or web browser of 16 channels in one screen. 3.4 Adjusting Live View Settings Purpose Live View settings can be customized according to different needs.
DS-720xHTI-Kx DVR User Manual If you set the video output resolution as 1024*768 in Menu > Configuration > General, when you set more than 16 windows, the following message box will pop up as below. If you set the video output resolution as 1280*720 or 1280*1024 in Menu > Configuration > General, if you set more than 25 windows, the following message box will pop up as below.
DS-720xHTI-Kx DVR User Manual 3) You can also click to start live view of all channels in order and click channels. Click or to go to the previous or next page. to stop live view of all 4) Click Apply. 3.5 Manual Video Quality Diagnostics Purpose The video quality of the analog channels can be diagnosed manually, and you can view the diagnostic results from a list. 1. Go to Menu > Manual > Manual Video Quality Diagnostics. Figure 3-12 Video Quality Diagnostics 2.
DS-720xHTI-Kx DVR User Manual Figure 3-13 Diagnostics Result Connect the camera to the device for the video quality diagnostics. Three exception types can be diagnosed: Blurred Image, Abnormal Brightness, and Color Cast.
DS-720xHTI-Kx DVR User Manual Chapter 4 PTZ Controls 4.1 Configuring PTZ Settings Purpose Configure the PTZ parameters before you attempt to control the PTZ camera. 1. Go to Menu > Cameras Setup > PTZ. Figure 4-1 PTZ Settings 2. Select the camera for PTZ setting in the Camera drop-down list. 3. Click PTZ Parameters to set the PTZ parameters.
DS-720xHTI-Kx DVR User Manual Figure 4-2 PTZ-Parameter Settings 4. Select the PTZ camera parameters from the drop-down list. All the parameters should be exactly the same as the PTZ camera parameters. For a connected Hikvision-C camera/dome, you can set the PTZ protocol to UTC. Make sure the protocol selected here is supported by the connected camera/dome. When UTC protocol is selected, all other parameters such as baud rate, data bit, stop bit, parity, and flow control are not configurable.
DS-720xHTI-Kx DVR User Manual 7. (Optional) Check the Enable Omnicast Control checkbox to enable the PTZ control of the selected camera via Omnicast VMS of Genetec. 4.2 Setting PTZ Presets, Patrols, and Patterns Before You Start Make sure that the presets, patrols, and patterns are supported by the PTZ protocols. 4.2.1 Customizing Presets Purpose To set the preset location you want the PTZ camera to point to when an event occurs. 1. Go to Menu > Cameras Setup > PTZ. Figure 4-4 PTZ Settings 2.
DS-720xHTI-Kx DVR User Manual 4.2.2 Calling Presets Purpose A preset enables the camera to point to a specified position such as a window when an event takes place. 1. Click PTZ in the lower-right corner of the PTZ setting interface or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar, or select the PTZ option in the right-click menu to show the PTZ control panel. 2. Choose Camera in the drop-down list. 3.
DS-720xHTI-Kx DVR User Manual Figure 4-6 PTZ Settings 2. Select patrol no. in the drop-down patrols list. 3. Click Set to add key points for the patrol. Figure 4-7 KeyPoint Configuration 4. Configure key point parameters such as key point no., key point stay duration, and patrol speed. The key point corresponds to the preset. KeyPoint No. determines the order in which the PTZ will follow while cycling through the patrol. Duration refers to the time interval to stay at the corresponding key point.
DS-720xHTI-Kx DVR User Manual 4.2.4 Calling Patrol Purpose Calling a patrol makes the PTZ move according the predefined patrol path. 1. Click PTZ in the lower-right corner of the PTZ Settings interface, or press PTZ on the front panel, or click the PTZ Control icon in the quick setting bar, or select the PTZ option in the right-click menu to show the PTZ control panel. 2. Click the General tab to show the general settings of the PTZ control. Figure 4-8 PTZ Panel - General 3.
DS-720xHTI-Kx DVR User Manual Figure 4-9 PTZ Settings 2. Choose pattern number in the drop-down list. 3. Click Start and click corresponding buttons in the control panel to move the PTZ camera, and click the Stop button to stop it. The PTZ movement is recorded as the pattern. 4.2.6 Calling Patterns Purpose Follow the procedure to move the PTZ camera according to the predefined patterns. 1.
DS-720xHTI-Kx DVR User Manual Figure 4-10 PTZ Panel - General 3. Click Call Pattern to call it. 4. Click Stop Pattern to stop calling it. 4.2.7 Customizing Linear Scan Limit Purpose Linear Scan can be enabled to trigger the scan in the horizantal direction in the predefined range. 1. Go to Menu > Cameras Setup > PTZ. Figure 4-11 PTZ Settings 2.
DS-720xHTI-Kx DVR User Manual The speed dome starts linear scan from the left limit to the right limit, and you must set the left limit to the left side of the right limit. Also, the angle from the left limit to the right limit should be no more than 180º. 4.2.8 Calling Linear Scan Purpose Follow the procedure to call the linear scan in the predefined scan range. 1.
DS-720xHTI-Kx DVR User Manual Figure 4-13 PTZ Panel - One-touch 3. There are three one-touch park types selectable. Click the button to activate the park action. • Park (Quick Patrol): The dome starts patrol from the predefined preset 1 to preset 32 in order after the park time. The undefined preset will be skipped. • Park (Patrol 1): The dome moves according to the predefined patrol 1 path after the park time. • Park (Preset 1): The dome moves to the predefined preset 1 location after the park time.
DS-720xHTI-Kx DVR User Manual Figure 4-14 PTZ Control Panels Table 1-11 Icon Descriptions of the PTZ Panel Icons Description Direction button and the auto-cycle button The speed of the PTZ movement 3D-Zoom Switch to the PTZ control interface Exit Icon Description Description Zoom+, Focus+, Iris+ Zoom-, Focus-, Iris- Light on/off Wiper on/off Image Centralization Switch to the one-touch control interface Minimize windows Menu When a Hikvision CVBS camera is connected, click UM DS-720xHTI-Kx 0129
DS-720xHTI-Kx DVR User Manual Chapter 5 Recording and Capture Settings 5.1 Configuring Encoding Parameters Before You Start 1. Make sure that the HDD has already been installed. If not, install and initialize an HDD, (Menu > System Configuration > HDD > HDD Information). Figure 5-1 HDD Information 2. Click the Advanced tab to check the storage mode of the HDD. (Menu > System Configuration > HDD > Storage Mode) 1) If the HDD mode is Quota, set the maximum record capacity. See 12.4 Configuring Quota Mode.
DS-720xHTI-Kx DVR User Manual Figure 5-3 Record Parameters 2. Set the recording parameters. 1) Select the Record tab to configure. 2) Select a camera from the camera drop-down list. 3) View the Camera Resolution. When TurboHD, AHD, or HD-CVI input is connected, you can view information including input signal type, resolution, and frame rate (e.g., 1080P30). When CVBS input is connected, you can view information such as NTSC or PAL.
DS-720xHTI-Kx DVR User Manual • Frame Rate: Set the recording frame rate. When an 8 MP signal input is connected, the main stream frame rate cannot exceed 12 fps. The minimum frame rate for the main stream is 1 fps. If you set different frame rates for continuous and event recording, when you click Apply to save the settings, the following note pops up: Figure 5-4 Note for Different Frame Rates • Max. Bitrate Mode: Set the mode to General or Custom.
DS-720xHTI-Kx DVR User Manual Figure 5-5 More Settings of Record Parameters • Pre-record: The time you set to record before the scheduled time or event. For example, when an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera records it at 9:59:55. • Post-record: The time you set to record after the event or the scheduled time.
DS-720xHTI-Kx DVR User Manual Figure 5-6 Copy Camera Settings 5. Set encoding parameters for sub-stream. 1) Select the Sub-Stream tab. Figure 5-7 Sub-Stream Encoding 2) Select a camera in the camera drop-down list. 3) Configure the parameters. 4) Click Apply to save the settings. 5) (Optional) If the parameters can also be used for other cameras, click Copy to copy the settings to other channels. The sub-stream resolution can be selected as WD1, 4CIF, or CIF.
DS-720xHTI-Kx DVR User Manual 5.2 Configuring Recording Schedule In this chapter, the record schedule procedure is used as an example. The same procedure can be applied to configure the recording schedule. Purpose Set the recording schedule, and the camera will automatically start/stop recording according to the configured schedule. 1. Go to Menu > Recording Configuration > Schedule.
DS-720xHTI-Kx DVR User Manual 2) In the message box, choose the day for which you want to set the schedule. 3) To schedule an all-day recording, check the All Day item checkbox. Figure 5-9 Edit Schedule 4) To arrange another schedule, leave the 24HR checkbox blank and set the Start/End times. Figure 5-10 Edit Schedule - Set Time Period Up to eight periods can be configured for each day, and the time periods cannot overlap.
DS-720xHTI-Kx DVR User Manual Figure 5-11 Copy Schedule to Other Days The Holiday option is available when you enable holiday schedule in Holiday Settings. See 5.7 Configuring Holiday Recording and Capture. 6) Click OK to save the settings and return to upper level menu. Draw the Schedule 1) Click the color icon to select a record type in the event list on the bottom of the interface. Figure 5-12 Draw the Recording Schedule 2) Drag the mouse on the schedule.
DS-720xHTI-Kx DVR User Manual Repeat Step 4 to set schedules for other channels. If the settings can also be used for other channels, click Copy, and then choose the channel you want to copy to. 5. Click Apply in the Record Schedule interface to save the settings. 5.3 Configuring Motion Detection Recording Purpose Follow the steps to set the motion detection parameters. In live view mode, once a motion detection event occurs, the DVR analyzes it and performs action(s) to handle it.
DS-720xHTI-Kx DVR User Manual Figure 5-14 Motion Detection Settings 6) Select the channels for which the motion detection event should trigger recording. 7) Click Apply to save the settings. 8) Click OK to return to the upper level menu. 9) Exit the Motion Detection menu. 3. Configure the schedule (see 5.
DS-720xHTI-Kx DVR User Manual Configuring Recording Schedule, and choose Motion as the record type). 5.4 Configuring Alarm Triggered Recording Purpose Follow the procedure to configure alarm triggered recording. 1. Go to Menu > Recording Configuration > Trigger > Alarm Input. Figure 5-15 Alarm Settings - Alarm Input 2. Select Alarm Input No. 3. Input Alarm Name. 4. Select N.O. (normally open) or N.C. (normally closed) for alarm type. 5. Check the Enable checkbox to enable alarm.
DS-720xHTI-Kx DVR User Manual Configuring Recording Schedule for detailed operations. Figure 5-16 Trigger Channel 7. Click Apply to save the settings. 8. Repeat steps 1 to 8 to configure other alarm input parameters. If the settings can also be applied to other alarm inputs, click Copy and choose the alarm input number. Figure 5-17 Copy Alarm Input 5.5 Configuring Event Recording Purpose Event triggered recording can be configured through the menu.
DS-720xHTI-Kx DVR User Manual For the analog channels, the line crossing detection and intrusion detection conflict with other VCA detection such as sudden scene change detection, face detection, and vehicle detection. You can enable only one function. 1. Go to Menu > Cameras Setup > VCA. Figure 5-18 VCA Settings 2. Select a Camera. 3. Configure the detection rules for VCA events. See 9.3 Line Crossing Detection. 4. Click Set to configure the alarm linkage actions for the VCA events. 5.
DS-720xHTI-Kx DVR User Manual 7. Enter Record Schedule Settings interface (Menu > Recording Configuration > Schedule), and set Event as the record type. See 5.2 Configuring Recording Schedule. 5.6 Configuring Manual Recording Purpose Follow the steps to set the manual recording parameters. Using manual recording, you need to manually cancel the record and capture. The manual recording is prior to the scheduled recording. 1. Go to Menu > Manual > Record. Figure 5-20 Manual Record 2. Enable manual record.
DS-720xHTI-Kx DVR User Manual Figure 5-21 Holiday Settings 2. Enable Edit Holiday schedule. 1) Click to enter the Edit interface. Figure 5-22 Edit Holiday Settings 2) Check the Enable checkbox. 3) Select Mode from the drop-down list. There are three different modes for the date format to configure holiday schedule. By Month, By Week, and By Date are selectable. 1) Set the start and end date. 2) Click Apply to save settings. 3) Click OK to exit the Edit interface. 3. Configure the record schedule.
DS-720xHTI-Kx DVR User Manual Up to eight periods can be configured for each day, and the time periods cannot overlap. In the channel time table, both holiday schedule and normal day schedule are displayed. 4. Repeat the above steps to set Holiday schedules for other channels. If the holiday schedule can also be used for other channels, click Copy and choose the channel for which you want to apply the settings. 5.
DS-720xHTI-Kx DVR User Manual 1) Select the camera you want to configure. 2) Click More Settings. Figure 5-25 More Settings 3) Set the following parameters: a) Pre-Record – Enter the number of seconds to record before the triggered event. b) Post-Record – Enter the number of seconds to record after the triggered event. c) Expired Time (day) – Enter the number days to keep the recording. d) Record Audio (checkbox) – Check to enable audio recording.
DS-720xHTI-Kx DVR User Manual 4. Click to enter the editing interface. 5. Assign the HDD group. 1) Use the radio selection button to choose a group number for the HDD group. 2) Click Apply to save your settings. 3) Click OK to return to the upper level menu. 6. Repeat the above steps to configure more HDD groups. 7. Choose the Channels for which you want to save the record files in the HDD group. 1) Go to Menu > System Configuration > HDD > Storage Mode.
DS-720xHTI-Kx DVR User Manual Figure 5-27 Export 2. Select the channels you want to investigate by checking the checkbox(es). 3. Configure the record mode, record type, file type, start time, and end time. 4. Click Search to show the results. Figure 5-28 Export-Search Result 5. Protect the record files. 1) Find the record files you want to protect, and then click the indicating that the file is locked. icon, which will turn to , Record files with recording not completed cannot be locked.
DS-720xHTI-Kx DVR User Manual Figure 5-29 HDD Information 2. Click to edit the HDD you want to protect. Figure 5-30 HDD Information - Editing 3. Set the HDD to Read-only. 4. Click OK to save the settings and return to the upper level menu. You cannot save any files to a Read-only HDD. To save files to the HDD, change the property to R/W. If there is only one HDD and it is set to Read-only, the DVR cannot record any files. Only live view mode is available.
DS-720xHTI-Kx DVR User Manual Figure 5-31 Advanced Settings 2. Click Enable to enable H.264+/H.265+ for all the analog cameras, and the following box pops up. Figure 5-32 Attention Box 3. Click Yes to enable the function and reboot the device to have the new settings take effect. One-Key Disabling H.264+/H.265+ for All Analog Cameras 1. Go to Menu > System Configuration > HDD > Record Information. 2. Click Disable to disable H.264+/H.265+ for all the analog cameras and the following box pops up.
DS-720xHTI-Kx DVR User Manual Chapter 6 Playback 6.1 Playing Back Record Files 6.1.1 Instant Playback Purpose Play back the recorded video files of a specific channel in live view mode. Channel switch is supported. Instant Playback by Channel Choose a channel in live view mode and click in the quick setting toolbar. In instant playback mode, only record files recorded during the last five minutes on this channel will be played back. Figure 6-1 Instant Playback Interface 6.1.
DS-720xHTI-Kx DVR User Manual Figure 6-2 Right-click Menu under Live View Playback by Time Purpose Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch are supported. 1. Go to Menu > Playback. 2. Check the checkbox of channel(s) in the channel list, then double-click to select a calendar date. Figure 6-3 Playback Calendar If there are record files for that camera on a day, the color for that day shows Event Record.
DS-720xHTI-Kx DVR User Manual You can also use the toolbar at the bottom of the Playback interface to control the playing progress. Figure 6-4 Playback Interface Select the channel(s) if you want to switch playback to another channel or execute simultaneous playback of multiple channels.
DS-720xHTI-Kx DVR User Manual The indicates the start time and end time of the record files. represents normal recording (manual or schedule); motion | alarm, motion & alarm). represents event recording (motion, alarm, Playback progress bar: use the mouse to click any point on the progress bar to locate special frames. 6.1.3 Playing Back by Event Search Purpose Play back record files on one or several channels searched out by restricting event type (motion detection, alarm input or VCA).
DS-720xHTI-Kx DVR User Manual Figure 6-7 Select Channels for Synchronous Playback 6. On the Event Playback interface, select main stream or sub-stream from the Playback drop-down list. The toolbar in the bottom of the Playback interface can be used to control the playing process. Figure 6-8 Playback by Event Interface Pre-play and post-play can be configured for playback of event triggered record files. • Pre-play: The time you set to play back before the event.
DS-720xHTI-Kx DVR User Manual 6.1.4 Playing Back by Tag Purpose Video tags allow you to record related information such as people and location of a certain time point during playback. You can also use video tag(s) to search for record files and position time points. Before Playing Back by Tag 1. Go to Menu > Playback. 2. Search and play back the record file(s). Refer to 6.1.2 Playing Back by Normal Search for detailed information about searching and playback of the record files.
DS-720xHTI-Kx DVR User Manual Figure 6-10 Add Tag A maximum of 64 tags can be added to a single video file. Tag Management 1. Click to check, edit and delete tag(s). Figure 6-11 Tag Management Interface 1) Select Tag from the drop-down list in the Playback interface. 2) Choose channels, edit start time and end time, then click Search to enter Search Result interface. You can enter keyword in the textbox UM DS-720xHTI-Kx 012918NA to search for the tag.
DS-720xHTI-Kx DVR User Manual Figure 6-12 Video Search by Tag 2. Click to play back the file. 3. You can click Back to return to the search interface. Pre-play and post-play can be configured. Click or to select the previous or next tag. 6.1.5 Playing Back by Smart Search Purpose The Smart Playback function provides an easy way to get through the less relevant information.
DS-720xHTI-Kx DVR User Manual Figure 6-13 Setting Intrusion Detection on IP Camera 2. Configure the required intrusion detection parameters, including area, arming schedule, and linkage methods. Refer to the Smart IP Camera user manual for detailed instructions. 1) Go to Menu > Playback. 2) Select Smart in the drop-down list on the top-left. 3) Select a camera in the camera list. Figure 6-14 Smart Playback Interface 4) Select a date in the calendar and click UM DS-720xHTI-Kx 012918NA to play.
DS-720xHTI-Kx DVR User Manual Table 1-13 Icon Explanation of the Smart Playback Toolbar Operation Icon Operation Draw line for the Draw quadrilateral line crossing for the intrusion detection detection Set full screen for Clear all motion detection File management Stop playing for video clips Icon Operation Draw rectangle for the intrusion detection / Start/stop clipping Search matched video files Smart settings / Pause playing /play Filter video files by setting the target characters Show/hide V
DS-720xHTI-Kx DVR User Manual Pre-play and post-play is not available for the motion event type. 5. Click to search and play the matched video files. 6. (Optional) Click to filter the searched video files by setting the target characters, including the gender and age of the human and whether he/she wears glasses. Figure 6-16 Set Result Filter The Result Filter function is supported by IP cameras only. 7. (Optional) For cameras supporting VCA, click to show the VCA information.
DS-720xHTI-Kx DVR User Manual If the connected camera does not support VCA, the icon is grey and unavailable. For analog cameras, the VCA information includes line crossing detection and intrusion detection. For IP cameras, the VCA information includes all the smart IP camera VCA detections. 6.1.6 Playing Back by System Logs Purpose Play back record file(s) associated with channels after searching system logs. 1. Go to Menu > Maintenance > System Logs. Figure 6-18 System Log Search Interface 2.
DS-720xHTI-Kx DVR User Manual 6.1.7 Playing Back by Sub-Periods Purpose The video files can be played in multiple sub-periods simultaneously on the screens. 1. Go to Menu > Playback. 2. Select Sub-periods from the drop-down list in the upper-left corner of the page to enter the Sub-periods Playback interface. 3. Select a date and start playing the video file. 4. Select the Split-screen Number from the drop-down list. Up to 16 screens are configurable.
DS-720xHTI-Kx DVR User Manual • Click to refresh the file list. 3. Select and click to play it. Figure 6-21 External File Playback Interface 6.2 Auxiliary Playback Functions 6.2.1 Playing Back Frame-by-Frame Purpose Play video files frame-by-frame to check image details of the video when abnormal events occur. 1. Go to the Playback interface and click until the speed changes to Single frame. 2. One click on the playback screen represents playback or reverse playback of one frame.
DS-720xHTI-Kx DVR User Manual Figure 6-22 Digital Zoom Draw Area 3. Right-click the image to exit the digital zoom interface. 6.2.3 Reverse Playback of Multi Channels Purpose You can play back record files of multi channels in reverse. Up to 16-ch simultaneous reverse playback is supported. 1. Go to Menu > Playback. 2. Check checkbox(es) to select multiple channels and click to select a date on the calendar. Figure 6-23 4-ch Synchronous Playback Interface 3.
DS-720xHTI-Kx DVR User Manual 6.2.4 File Management Purpose Manage video clips, pictures captured in playback, locked files, and tags added in playback mode. 1. Go to Menu > File Management > Record. Figure 6-24 File Management > Record 2. Check the cameras you wish to search. 3. Set the search filters: a. Record Mode ˗ Main Stream ˗ Sub Stream b. Recording Mode ˗ Continuous ˗ Event ˗ Manual ˗ All c. File Type ˗ Unlocked ˗ Locked ˗ All d. Start Time e.
DS-720xHTI-Kx DVR User Manual Figure 6-25 File Management > Event 4. You can view the saved video clips, captured playback pictures, lock/unlock the files, and edit the tags that you added in the playback mode. 5. If required, select the items and click Export All or Export to export the clips/pictures/files/tags to a local storage device.
DS-720xHTI-Kx DVR User Manual Chapter 7 Backup 7.1 Backing up Record Files Before You Start Attach the backup device(s) to the DVR. 7.1.1 Backing up by Normal Video/Picture Search Purpose The record files or pictures can be backed up to various devices such as USB devices (USB flash drives, USB HDDs, USB writer), SATA writer, and e-SATA HDD. Back up Using USB Flash Drives and USB HDDs. 1. Go to Menu > File Management. • To Choose Record Files To Back Up 1. Select Record on the left panel. 2.
DS-720xHTI-Kx DVR User Manual Figure 7-1 Menu > File Management > Record • To Choose the Event Files To Back Up: Select Event on the left panel. 1. Select Event on the left panel. 2. Set the search conditions. a. Major Type b. Recording Mode c. Start Time d. End Time e. Pre-Play f. Post-Play 3. Use the checkboxes to select which cameras to search. 4. Click Search to display the found files.
DS-720xHTI-Kx DVR User Manual Figure 7-2 Menu > File Management > Event 2. The matched video files are displayed in Chart or List display mode. 1) Click to play the record file if you want to check it. 2) Check the checkbox adjacent to the video files you want to back up. The size of the currently selected files is displayed in the lower-left corner of the window.
DS-720xHTI-Kx DVR User Manual 3. Select video files from the Chart or List to export, and click Export to enter the Export interface. You can also click Export All to select all the video files for backup and enter the Export interface. Figure 7-4 Export using USB Flash Drive 4. Select the backup device from the drop-down list and you can also select the file format to filter the files existing in the backup device. 5. Select the saving format type. 6.
DS-720xHTI-Kx DVR User Manual Figure 7-6 Export Finished Backing up pictures using a USB writer or SATA writer uses the same procedures as above. 7.1.2 Backing up Video Clips Purpose You may also select video clips in playback mode to export directly during playback, using USB devices (USB flash drive, USB HDD, USB writer), or a SATA writer. 1. Go to Menu > Playback. 2. During playback, use or in the playback toolbar to start or stop clipping record file(s).
DS-720xHTI-Kx DVR User Manual 3. Click to enter the file management interface. Figure 7-8 Video Clips Export Interface 4. Check the checkboxes of video clips you want to export. 5. Click Export. Figure 7-9 Export 6. Double-click a folder to save the chosen video clips to (click New Folder to create a new folder). 7. Click Export to save the video clips.
DS-720xHTI-Kx DVR User Manual 8. To format the disk, click Format. 9. To delete a file, highlight the file and click . If the inserted storage device is not recognized, click Refresh. If it is still not recognized, disconnect then reconnect the device. If it is still not recognized, check for compatibility from vendor.
DS-720xHTI-Kx DVR User Manual Chapter 8 Alarm Settings 8.1 Setting Motion Detection 1. Go to Menu > Recording Configuration > Motion Detect. Figure 8-1 Motion Detection Setup Interface 2. Select a camera for which you want to set up motion detection. 3. Set detection area and sensitivity. 1) Check checkbox to enable motion detection. Use the mouse to draw detection area(s) or click Full Screen to set the detection area to be the full screen, and drag the sensitivity bar to set sensitivity.
DS-720xHTI-Kx DVR User Manual Figure 8-2 Set Motion Detection Trigger Camera 4. Click Trigger Channel tab and select one or more channels which will start to record or become full-screen monitoring when motion alarm is triggered. 5. Set the channel’s arming schedule. 1) Select Arming Schedule tab. 2) Choose one day of a week, with up to eight time periods set within each day, or click Copy to copy the time period settings to other day(s). Time periods cannot repeat or overlap.
DS-720xHTI-Kx DVR User Manual 6. Click Linkage Action tab to set up motion alarm response actions (refer to 8.8 Setting Alarm Response Actions). Figure 8-4 Set Motion Detection Linkage Action 7. Repeat the above steps to set up arming schedule for other days of the week. 8. Click OK to complete the channel motion detection settings. 9. To set motion detection for another channel, repeat the above steps or copy the above settings to it. You are not allowed to copy the “Trigger Channel” action. 8.
DS-720xHTI-Kx DVR User Manual Figure 8-5 Motion Detection 2. Select the connected PIR camera. 3. Check Enable Motion Detection. 4. Check False Alarm Filter to enable PIR motion detection. The message box pops up as below. Figure 8-6 Note 5. Click OK to enable PIR motion detection. Then, only when the motion detection events and PIR events are both triggered, the motion detection alarm will be triggered. 6. Set detection area and sensitivity. Refer to 8.1 Setting Motion Detection. 7.
DS-720xHTI-Kx DVR User Manual 8.3 Setting Sensor Alarms Purpose Set up external sensor alarm handling method. 1. Go to Menu > Recording Configuration > Trigger > Alarm Input. Figure 8-7 Alarm Input Settings Interface 2. Set the handling method of the selected alarm input. 1) Check the Enable Alarm Input checkbox and click Set to set its alarm response actions. Figure 8-8 Set Trigger Channel of Alarm Input 3.
DS-720xHTI-Kx DVR User Manual 1) Select one day of a week, and a maximum of eight time periods can be set within each day. Time periods shall not repeat or overlap. Figure 8-9 Alarm Arming Schedule 5. Select Linkage Action tab to set up alarm response actions of the alarm input (refer to 8.8 Setting Alarm Response Actions). 1) Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy to copy an arming schedule to other days. Figure 8-10 Alarm Linkage Actions 6.
DS-720xHTI-Kx DVR User Manual Figure 8-11 Set PTZ Linking of Alarm Input 7. If you want to set handling action of another alarm input, repeat the above steps or just copy the above settings to it. Figure 8-12 Copy Alarm Input Settings 8. (Optional) Enable the one-key disarming for local alarm input 1 (Local<-1). 1) Check the Enable One-Key Disarming checkbox. 2) Click Settings to enter the linkage action settings interface.
DS-720xHTI-Kx DVR User Manual Figure 8-13 Disarm Linkage Actions When alarm input 1 (Local<-1) is enabled with one-key disarming, the other alarm input settings are not configurable. 8.4 Detecting Video Loss Purpose Detect video loss of a channel and take alarm response action(s). 1. Go to Menu > Cameras Setup > Video Loss. Figure 8-14 Video Loss Setup Interface 2. Select a Camera you want to detect. 3. Set up the video loss handling method. 1) Check the Enable Video Loss Alarm checkbox.
DS-720xHTI-Kx DVR User Manual 4. Set the channel’s arming schedule. 1) Select the Arming Schedule tab to set the channel’s arming schedule. 2) Choose one day of a week, and up to eight time periods can be set within each day. Time periods must not repeat or overlap. Figure 8-15 Set Video Loss Arming Schedule 3) Repeat the above steps to set the arming schedule for other days of a week. You can also use Copy to copy an arming schedule to other days. 5.
DS-720xHTI-Kx DVR User Manual 8.5 Detecting Video Tampering Purpose Trigger an alarm when the lens is covered and take alarm response action(s). 1. Go to Menu > Cameras Setup > Video Tampering Detection. Figure 8-17 Video Tampering Interface 2. Select a Camera for which you want to detect video tampering. 3. Check the Enable Video Tampering Detection checkbox. 4. Drag the sensitivity bar and choose a sensitivity level. 5. Click Set to set the video tampering handling method.
DS-720xHTI-Kx DVR User Manual 3) Select Linkage Action tab to set the video tampering alarm response actions of (refer to 8.8 Setting Alarm Response Actions). 4) Repeat the above steps to set arming schedule for other days of the week. You can use Copy to copy an arming schedule to other days. 5) Click OK to complete the channel’s video tampering settings. 6) Repeat the above steps to finish setting other channels, or click Copy to copy the above settings to them. 6.
DS-720xHTI-Kx DVR User Manual Figure 8-20 Video Quality Diagnostics Interface 2. Select a Camera for which you want to detect video tampering. 3. Check the Enable Video Quality Diagnostics checkbox. To enable video quality diagnostics, the function must be supported by the selected camera. 4. Enable and set the threshold of the diagnostic types, there are Blurred Image, Abnormal Brightness, and Color Cast.
DS-720xHTI-Kx DVR User Manual Figure 8-21 Set Video Quality Diagnostics Arming Schedule 3) Select the Linkage Action tab to set the alarm’s video quality diagnostics alarm response actions (refer to 8.8 Setting Alarm Response Actions). 4) Repeat the above steps to set the arming schedules for other days of the week. You can also use Copy to copy an arming schedule to other days. 5) Click OK to complete the channel’s video quality diagnostics settings.
DS-720xHTI-Kx DVR User Manual • Illegal Login: Incorrect user ID or password • Input/Recording Resolution Mismatch: The input resolution is lower than the recording resolution • Record/Capture Exception: No space for saving recorded files or captured pictures • PoC Module Exception: DVR cannot detect PoC module or PoC module powered off abnormally 1. Go to Menu > System Configuration > Exceptions. Figure 8-23 Exception Settings Interface (Event/Exception icon) when an exceptional 2.
DS-720xHTI-Kx DVR User Manual Figure 8-25 Detailed Event 3. Set the alarm linkage actions. For details, 8.8 Setting Alarm Response Actions. 4. Click Apply to save the settings. 8.8 Setting Alarm Response Actions Purpose Alarm response actions will be activated when an alarm or exception occurs, including Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Send E-mail, and Trigger Alarm Output.
DS-720xHTI-Kx DVR User Manual Send E-Mail Send an e-mail with alarm information to a user or users when an alarm is detected (see 11.2.7 Configuring Email for details of e-mail configuration). Trigger Alarm Output Trigger an alarm output when an alarm is triggered. 1. Go to Menu > Recording Configuration > Trigger > Alarm Output. 2. Select an alarm output, and set the alarm name and dwell time.
DS-720xHTI-Kx DVR User Manual Figure 8-27 Set Alarm Output Arming Schedule 4. Repeat the above steps to set arming schedules for other days of the week. You can also click Copy to copy an arming schedule to other days. 5. Click OK to complete the alarm output arming schedule setting. 6. Click Apply to save the settings.
DS-720xHTI-Kx DVR User Manual Chapter 9 VCA Alarm Purpose The DVR can receive a VCA alarm (line crossing detection, intrusion detection, sudden scene change detection, and audio exception detection) sent by an analog camera,. The VCA detection must first be enabled and configured on the camera settings interface. All other VCA detection features must be supported by the connected IP camera.
DS-720xHTI-Kx DVR User Manual 4. Set the VCA detection type to Face Detection. 5. Click Set to enter the Face Detection Settings interface. Configure the trigger channel, arming schedule, linkage action, and PTZ linking for the face detection alarm. Refer to 8.3 Setting Sensor Alarms for detailed instructions. Figure 9-2 PTZ Linking 6. Click Rule Settings to set the face detection rules. You can drag the slider to set the detection sensitivity. • Sensitivity: Range [1-5].
DS-720xHTI-Kx DVR User Manual Figure 9-4 Set Vehicle Detection 6. Click Set to configure the trigger channel, arming schedule, linkage action, and PTZ linking. PTZ linking is applicable only to other lists, not to whitelist or blacklist. 7. Click Rule Settings to enter the rule settings interface. Configure the lane, upload picture, and overlay content settings. Up to four lanes are selectable. Figure 9-5 Rule Settings 8. Click Save to save the settings.
DS-720xHTI-Kx DVR User Manual 9.3 Line Crossing Detection Purpose This function can detect people, vehicles, and objects that cross a set virtual line. The line crossing direction can be set as bidirectional, from left to right, or from right to left. You can set the duration for the alarm response actions such as full screen monitoring, audible warning, etc. 1. Go to Menu > Camera Setup > VCA. 2. Select the camera for which to configure the VCA.
DS-720xHTI-Kx DVR User Manual 7. Click and set two points in the preview window to draw a virtual line. Use virtual line and re-draw it. to clear the existing Up to four rules can be configured. Figure 9-7 Draw Line for Line Crossing Detection 8. Click Apply to activate the settings. Sudden scene change detection and line crossing detection cannot be enabled on the same channel. 9.
DS-720xHTI-Kx DVR User Manual 2) Drag the slider to set the detection sensitivity. Sensitivity: Range [1-100]. Defines the size of the object that will trigger the alarm. The higher the value, the more easily the detection alarm is triggered. Percentage: Range [1-100]. Defines the ratio of the in-region part of the object that will trigger the alarm. For example, if the percentage is set as 50%, if the object enters the region and occupies half of the whole region, the alarm is triggered.
DS-720xHTI-Kx DVR User Manual Sudden scene change detection and intrusion detection cannot be enabled on the same channel. 9.5 Region Entrance Detection Purpose Region entrance detection detects people, vehicles, or other objects that enter a pre-defined virtual region, and certain actions can be taken when the alarm is triggered. 1. Go to Menu > Cameras Setup > VCA. 2. Select the camera for which to configure the VCA. 3. Check the Save VCA Picture checkbox to save the captured VCA detection pictures. 4.
DS-720xHTI-Kx DVR User Manual Up to four rules can be configured. 9. Click Apply to save the settings. 9.6 Region Exiting Detection Purpose Region exiting detection detects people, vehicles, or other objects that exit from a pre-defined virtual region, and certain actions can be taken when the alarm is triggered. Refer to 9.5 Region Entrance Detection for steps to configure region exiting detection. Up to four rules can be configured. 9.
DS-720xHTI-Kx DVR User Manual 9.9 Fast Moving Detection Purpose Fast moving detection alarm is triggered when people, vehicles, or other objects move fast in a pre-defined virtual region, and a series of actions can be taken when the alarm is triggered. Refer to 9.4 Intrusion Detection for steps to configure fast moving detection. Sensitivity in the Rule Settings defines the moving speed of the object that will trigger the alarm. The higher the value, the more easily a moving object will trigger the alarm.
DS-720xHTI-Kx DVR User Manual 9.12 Object Removal Detection Purpose The object removal detection function detects objects removed from a pre-defined region such as exhibits on display, and a series of actions can be taken when the alarm is triggered. Refer to 9.4 Intrusion Detection for steps to configure object removal detection. Threshold [5s-20s] in the Rule Settings defines the time the objects have been removed from the region.
DS-720xHTI-Kx DVR User Manual Figure 9-11 Set Audio Exception Detection Rules 1) Check the Audio Loss Exception checkbox to enable audio loss detection. 2) Check the Sudden Increase of Sound Intensity Detection checkbox to detect a steep sound rise in the surveillance scene. You can set the detection sensitivity and threshold. Sensitivity: Range [1-100]. The smaller the value, the more severe the change must be to trigger detection. Sound Intensity Threshold: Range [1-100]. Filters the environment sounds.
DS-720xHTI-Kx DVR User Manual Refer to 9.1 Face Detection for steps to configure scene change detection. Sensitivity in the Rule Settings ranges from 1 to 100, and the higher the value, the more easily the change of scene will trigger the alarm. For analog cameras, the line crossing detection and intrusion detection conflict with other VCA detection such as sudden scene change detection, face detection, and vehicle detection. You can enable only one function.
DS-720xHTI-Kx DVR User Manual Chapter 10 VCA Search With the configured VCA detection, the device supports VCA search for behavior search, face search, plate search, people counting, and heat map results of the IP cameras. 10.1 Face Search Purpose When there are detected face pictures captured and saved in the HDD, you can enter the Face Search interface to search for and play the picture related video files according to the specified conditions. Before You Start Refer to 9.
DS-720xHTI-Kx DVR User Manual Figure 10-2 Face Search Interface 7. Play the face picture related video file. • You can double click on a face picture to play its related video file in the view window on the top right, or select a picture item and click to play it. • You can click to stop the playing, or click / to play the previous/next file. 8. To export the captured face pictures to a local storage device, connect the storage device to the device and click Export All to enter the Export interface.
DS-720xHTI-Kx DVR User Manual 10.2 Behavior Search Purpose Behavior analysis detects a series of suspicious behaviors based on VCA detection, and certain linkage methods will be enabled if the alarm is triggered. 1. Go to Menu > VCA Search > Behavior Search. 2. Select the camera(s) for the behavior search. 3. Specify the start time and end time for searching the matched pictures. Figure 10-4 Behavior Search Interface 4.
DS-720xHTI-Kx DVR User Manual 6. Play the behavior analysis picture related video file. • Double click on a picture from the list to play its related video file in the view window on the top right, or select a picture item and click to play it. • Click to stop the playing, or click / to play the previous/next file. 7. To export the captured pictures to a local storage device, connect the storage device to the device and click Export All to enter the Export interface.
DS-720xHTI-Kx DVR User Manual 10.4 People Counting Purpose People Counting calculates the number of people entering or leaving a configured area and creates daily/weekly/monthly/annual reports for analysis. 1. Go to Menu > VCA Search > People Counting. 2. Select the camera for the people counting. 3. Select the report type to Daily Report, Weekly Report, Monthly Report, or Annual Report. 4. Set the statistics time. 5. Click Counting to start people counting statistics.
DS-720xHTI-Kx DVR User Manual Figure 10-8 Heat Map Interface 5. Click Counting to export the report data and start heat map statistics, and the results are displayed graphically in different colors. As shown in Figure 10-8, the red color block (255, 0, 0) indicates the most visited area, and the blue color block (0, 0, 255) indicates the less-popular area. 6. Click Export to export the statistics report in Microsoft Excel format.
DS-720xHTI-Kx DVR User Manual Chapter 11 Network Settings 11.1 Configuring General Settings Purpose Network settings must be properly configured before you operate the DVR over a network. 1. Go to Menu > System Configuration > Network > General. Figure 11-1 Network Settings Interface 2. On the General Settings interface, you can configure the following parameters: NIC Type, IPv4 Address, IPv4 Gateway, MTU, DNS Server, and Main NIC. The valid value of MTU is from 500 to 1500.
DS-720xHTI-Kx DVR User Manual 11.2 Configuring Advanced Settings 11.2.1 Configuring Hik-Connect Purpose Hik-Connect provides a mobile phone application and the service platform page (www.hik-connect.com) to access and manage your connected DVR, which enables convenient remote access to the surveillance system. Hik-Connect can be enabled via operation on SADP software, GUI, and Web browser. We introduce the GUI operation steps in this section. 1.
DS-720xHTI-Kx DVR User Manual Figure 11-3 Service Terms 1) Create the verification code, and enter the code in the Verification Code text field. 2) Check the The Hik-Connect service will require internet access. Please read Service Terms and Privacy Statement before enabling the service. checkbox. 3) Scan the QR code on the interface to read the Service Terms and the Privacy Statement. 4) Click OK to save the settings and return to the Hik-Connect interface. Hik-Connect is disabled by default.
DS-720xHTI-Kx DVR User Manual Figure 11-4 Hik-Connect Settings Interface 5. Click Apply to save the settings. 6. After configuration, you can access and manage the DVR with your mobile phone or the Web site (www.hik-connect.com). • iOS Users: Scan the QR code below to download the Hik-Connect app for subsequent operations. Figure 11-5 QR Code for iOS Users • Android Users: Scan the QR code below to download the Hik-Connect app for subsequent operations.
DS-720xHTI-Kx DVR User Manual Refer to the help file on the official Web site (www.hik-connect.com) and the Hik-Connect Mobile Client User Manual for adding the device to Hik-Connect and more operation instructions. 11.2.2 Configuring DDNS Purpose If your DVR is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to be used for network access. Prior registration with your ISP is required before configuring the system to use DDNS. 1.
DS-720xHTI-Kx DVR User Manual • PeanutHull 1) Enter the User Name and Password obtained from the PeanutHull Web site. Figure 11-8 PeanutHull Settings Interface • NO-IP Enter the account information in the corresponding fields. Refer to the DynDNS settings. 1) Enter Server Address for NO-IP. 2) In the Device Domain Name text field, enter the domain obtained from the NO-IP Web site (www.no-ip.com). 3) Enter the User Name and Password registered in the NO-IP Web site.
DS-720xHTI-Kx DVR User Manual Figure 11-10 NTP Settings Interface 2. Check the Enable NTP checkbox to enable this feature. 3. Configure the following NTP settings: • Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute. • NTP Server: IP address of NTP server. • NTP Port: Port of NTP server. 4. Click Apply to save and exit the interface. The time synchronization interval can be set from 1 to 10,080 minutes, and the default value is 60 minutes.
DS-720xHTI-Kx DVR User Manual Figure 11-11 UPnP™ Settings Interface 2. Check Enable UPnP checkbox to enable UPnP™. 3. Set the Mapping Type as Manual or Auto in the drop-down list. OPTION 1: Auto If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router automatically. 1) Click Apply to save the settings. 2) Click Refresh to get the latest status of the port mapping.
DS-720xHTI-Kx DVR User Manual 2) Click Apply to save the settings. 3) Click Refresh to get the latest status of the port mapping. 11.2.5 Configuring More Settings 1. Go to Menu > System Configuration > Network > More Settings. Figure 11-13 More Settings Interface 2. Configure the remote alarm host, server port, HTTP port, multicast, and RTSP port. • Alarm Host IP/Port: With a remote alarm host configured, the device will send the alarm event or exception message to the host when an alarm is triggered.
DS-720xHTI-Kx DVR User Manual • Output Bandwidth Limit: Check the checkbox to enable output bandwidth limit. • Output Bandwidth: After enabling the output bandwidth limit, input the output bandwidth in the text field. The output bandwidth limit is used for remote live view and playback. The default output bandwidth is the maximum limit. 3. Click Apply to save and exit the interface. 11.2.
DS-720xHTI-Kx DVR User Manual OPTION 1: Create the self-signed certificate 1) Click Create to create the following dialog box. Figure 11-15 Create Self-Signed Certificate 2) Enter the country, host name/IP, validity, and other information. 3) Click OK to save the settings. OPTION 2: Create the authorized certificate 1) Click Create to create the certificate request. 2) Download the certificate request, and submit it to the trusted certificate authority for signature.
DS-720xHTI-Kx DVR User Manual Before You Start Make sure you configured the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway, and the Preferred DNS Server in the Network Settings menu. Refer to 11.1 Configuring General Settings for detailed information. 1. Go to Menu > System Configuration > Network > Email. 2. Select the Email tab to enter the Email Settings interface. Figure 11-17 Email Settings Interface 3.
DS-720xHTI-Kx DVR User Manual For analog cameras, three attached pictures can be sent for one analog camera when an alarm is triggered. • Interval: The interval refers to the time between two actions of sending attached pictures. • E-mail Test: Sends a test message to verify that the SMTP server can be reached. 4. Click Apply to save the e-mail settings. 5. Click Test to test your e-mail settings. The corresponding Attention message box pops up. Figure 11-18 Email Testing Attention 11.2.
DS-720xHTI-Kx DVR User Manual Figure 11-20 Network Detection Interface 2. Select a NIC to test network delay and packet loss. 3. Enter the destination address in the Destination Address text field. 4. Click Test to start testing network delay and packet loss. 11.3.2 Exporting Network Packet Purpose By connecting the DVR to a network, the captured network data packet can be exported to a USB flash disk, SATA, or other local backup device. 1. Go to Menu > Maintenance > Network Detect > Network Detection. 2.
DS-720xHTI-Kx DVR User Manual 2. After exporting is complete, click OK to finish the packet export. Figure 11-22 Packet Export Attention Up to 1 MB of data can be exported each time. 11.3.3 Checking Network Status Purpose You can check the network status and set the network parameters in this interface. 1. Go to Menu > Maintenance > Network Detect > Network Detection. 2. Click Status on the right bottom of the interface. Figure 11-23 Checking Network Status 3.
DS-720xHTI-Kx DVR User Manual Figure 11-25 Network Parameters Configuration 11.3.4 Checking Network Statistics Purpose You can check the network statistics to obtain the real-time information of the device. 1. Go to Menu > Maintenance> Network Detect > Network Stat. Figure 11-26 Network Stat. Interface 2. View the Remote Live View bandwidth, Remote Playback bandwidth, and Net Total Idle bandwidth. 3. Click Refresh to get the latest bandwidth statistics.
DS-720xHTI-Kx DVR User Manual Chapter 12 HDD Management 12.1 Initializing HDDs Purpose A newly installed hard disk drive (HDD) must be initialized before it can be used with the DVR. 1. Go to Menu > System Configuration > HDD > HDD Information. Figure 12-1 HDD Information Interface You can view the Total Capacity, Free Space, and Remaining Recording Time of the HDD. The algorithm of the Remaining Recording Time uses average bit rate for the channel, enabling smart encoding to raise accuracy. 2.
DS-720xHTI-Kx DVR User Manual 5. After the HDD has been initialized, the HDD status will change from Uninitialized to Normal. Initializing the HDD will erase all data on it. HDDs that are idle for a long period of time can be put to sleep to decrease the power consumption and extend the life of the HDDs. 1. Go to Menu > System Configuration > HDD > Record Information. Figure 12-4 Enable HDD Sleeping 2.
DS-720xHTI-Kx DVR User Manual 2. Click Add NetHDD to enter the Add NetHDD interface. Figure 12-6 Add NetHDD 3. Add the allocated NetHDD. 4. Set the type to NAS or IP SAN. 5. Configure the NAS or IP SAN settings. • Add a NAS Disk 1) Enter the NetHDD IP address in the text field. 2) Click Search to search for available NAS disks. 3) Select the NAS disk from the list shown below, or manually enter the directory in the NetHDD Directory text field. 4) Click OK to add the configured NAS disk.
DS-720xHTI-Kx DVR User Manual 12.3 Managing HDD Group 12.3.1 Setting HDD Groups Purpose Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD group through HDD settings. 1. Go to Menu > System Configuration > HDD > Storage Mode. 2. Set the Mode to Group, as shown below. Figure 12-7 Storage Mode Interface 3. Click Apply and the following Attention box will pop up. Figure 12-8 Attention for Reboot 4.
DS-720xHTI-Kx DVR User Manual Figure 12-9 Local HDD Settings Interface 7. Select the Group number for the current HDD. The default group no. for each HDD is 1. 8. Click OK to confirm the settings. Figure 12-10 Confirm HDD Group Settings 9. In the pop-up Attention box, click Yes to finish the settings. 12.3.2 Setting HDD Property Purpose The HDD property can be set to redundancy, read-only, or read/write (R/W). Before setting the HDD property, set the storage mode to Group (refer to step1-4 of 12.3.
DS-720xHTI-Kx DVR User Manual Figure 12-11 Set HDD Property 3. Set the HDD property to R/W, Read-only, or Redundancy. 4. Click OK to save the settings and exit the interface. 5. In the HDD Information menu, the HDD property will be displayed. At least two hard disks must be added to your DVR to set an HDD to Redundancy, with one HDD having R/W property. 12.4 Configuring Quota Mode Purpose Each camera can be configured with an allocated quota for the storage of recorded files. 1.
DS-720xHTI-Kx DVR User Manual 4. Enter the storage capacity in the Max. Record Capacity (GB) text field. 5. Copy the quota settings of the current camera to other cameras if required. Click Copy to enter the Copy Camera interface, as shown below. Figure 12-13 Copy Settings to Other Camera(s) 6. Select the camera(s) to be configured with the same quota settings. You can also click the Analog checkbox to select all cameras. 7. Click OK to finish the Copy settings and return to the Storage Mode interface. 8.
DS-720xHTI-Kx DVR User Manual Figure 12-14 Cloud Storage Interface 4. Follow the prompts and use a mobile QR Code scanner app to scan the QR code to log in to the selected cloud to get the authentication code, then copy the authentication code to the Authentication Code text filed. 5. Click Apply to save the settings and return to the main menu. 6. Enter the cloud storage interface again in approximately 20 seconds. The Status should indicate successful registration. 7.
DS-720xHTI-Kx DVR User Manual Configuring Recording Schedule). 8. Upload the event triggered recording files to the cloud storage. 1) Go to Menu > System Configuration > HDD > Cloud Storage. 2) Select the camera you set in the recording schedule interface. 3) Select the upload type in the Upload Type text filed. 4) Check the Enable Event Upload checkbox. 5) Click Apply to finish the settings.
DS-720xHTI-Kx DVR User Manual Only the sub-stream recorded files can be uploaded to the cloud storage. Configure the event triggered recording schedule and enable the corresponding event type. 9. (Optional) Click Copy to copy the cloud storage settings to other cameras. You can also click the Analog/IP Camera checkbox to select all cameras. 10. Click OK to return to the cloud storage interface, and click Apply to finish the settings. Figure 12-16 Copy to Interface 12.
DS-720xHTI-Kx DVR User Manual 12.7 Checking S.M.A.R.T. Information Purpose The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures. 1. Go to Menu > Maintenance > HDD Detect > S.M.A.R.T. Settings. 2. Select the HDD to view its S.M.A.R.T. information list, as shown below. To use the HDD even when the S.M.A.R.T.
DS-720xHTI-Kx DVR User Manual Figure 12-19 Bad Sector Detecting 3. Click Pause to pause the detection, and click Resume to resume the detection. 4. If there is error information about the HDD, click Error Info to view the information. 12.9 Configuring HDD Error Alarms Purpose You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal. 1. Go to Menu > System Configuration > Exceptions. 2. Set the Exception Type to HDD Error from the drop-down list. 3.
DS-720xHTI-Kx DVR User Manual Chapter 13 Camera Settings 13.1 Configuring OSD Settings Purpose You can configure the camera’s OSD (On-Screen Display) settings (e.g., date/time, camera name, etc.) 1. Go to Menu > Cameras Setup > OSD. 2. Select the camera to configure OSD settings. 3. Edit the Camera Name in the text field. 4. Configure the Display Name, Display Date, and Display Week by checking the checkbox(es). 5. Select the Date Format, Time Format, Display Mode, and the OSD Font.
DS-720xHTI-Kx DVR User Manual 13.2 Configuring Privacy Mask Purpose You can configure the four-sided privacy mask zones that cannot be viewed or recorded by the operator. 1. Go to Menu > Cameras Setup > Privacy Mask. 2. Select the camera for which to set the privacy mask. 3. Check the Enable Privacy Mask checkbox to enable this feature. Figure 13-2 Privacy Mask Settings Interface 4. Use the mouse to draw a zone on the window. The zones will be marked in different frame colors.
DS-720xHTI-Kx DVR User Manual 13.3 Configuring Video Parameters 13.3.1 Configuring Image Settings 1. Go to Menu > Cameras Setup > Image > Image Settings. Figure 13-4 Image Settings Interface (Choices Will Vary by Camera) 2. Select the camera for which to set the image parameters. 3. Two periods for different image settings are provided, select the period name in the drop-down list. The time periods cannot overlap. 4. Select the mode from the Mode drop-down list.
DS-720xHTI-Kx DVR User Manual Figure 13-5 Camera Parameters Settings 2. Select the Camera from the drop-down list. 3. Configure the parameters. • Switch the 4 MP or 5 MP signal with the Signal Switch drop-down list. 4 MP 25/30 fps and 5 MP 20 fps are selectable. The 4 MP 25 fps and 4 MP 30 fps signals are self-adaptive for the camera. • Check Enable Defog to enable the selected camera’s defog function. Set Defog Level from 1 to 4.
DS-720xHTI-Kx DVR User Manual Chapter 14 DVR Management and Maintenance 14.1 Viewing System Information 1. Go to Menu > System Information 2. Select the type of information you wish to view. • Device Info • Camera • Record • Alarm • Network • HDD Figure 14-1 System Information Interface (Device Info) 14.2 Searching Log Files Purpose The operation, alarm, exception, and DVR information can be stored in log files, which can be viewed and exported at any time. 1.
DS-720xHTI-Kx DVR User Manual Figure 14-2 Log Search Interface 2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type, and Minor Type. 3. Click Search to start search log files. 4. The matched log files will be displayed on the list shown below. Up to 2000 log files can be displayed each time. Figure 14-3 Log Search Results 5. Click of each log or double-click it to view its detailed information. You can also click the related video files, if available.
DS-720xHTI-Kx DVR User Manual Figure 14-4 Log Information Interface 6. To export the log files, click Export to enter the Export menu, as shown below. Figure 14-5 Export Log Files 7. Select the backup device from the Device Name drop-down list. 8. Click Export to export the log files to the selected backup device. 9. Click New Folder to create a new folder in the backup device, or click Format to format the backup device before log export. Connect the backup device to the DVR before operating log export.
DS-720xHTI-Kx DVR User Manual be edited on your PC (e.g., adding or deleting content, copying the setting to other devices by importing the Excel file to it, etc.). 1. Go to Menu > Cameras Setup > Cameras > IP Camera Import/Export. 2. Click Export to export configuration files to the selected local backup device. 3. To import a configuration file, select the file from the selected backup device and click Import. After the importing process is completed, you must reboot the DVR. 14.
DS-720xHTI-Kx DVR User Manual Figure 14-7 Local Upgrade Interface 3. Select the update file from the backup device. 4. Click Upgrade to start upgrading. 5. After the upgrading is completed, reboot the DVR to activate the new firmware. 14.5.2 Upgrading by FTP Before You Start Configure PC (running FTP server) and DVR to the same Local Area Network. Run third-party TFTP software on the PC, and copy the firmware into the TFTP root directory. 1. Go to Menu > Maintenance > Upgrade > FTP Upgrade.
DS-720xHTI-Kx DVR User Manual 14.6 Upgrading Camera Purpose You can upgrade multiple connected analog cameras supporting TurboHD or AHD signal simultaneously with the DVR. 1. Go to Menu > Maintenance > Upgrade > Camera Upgrade. Figure 14-9 Camera Upgrade 2. Check the checkbox(es) of the analog camera(s) to upgrade. The analog camera(s) must support TurboHD or AHD signal. 3. Select the update file from the backup device. 4. Click Upgrade to start upgrading. 14.7 Restoring Default Settings 1.
DS-720xHTI-Kx DVR User Manual • Restore Defaults: Restore all parameters, except the network (including IP address, subnet mask, gateway, MTU, NIC working mode, default route, server port, etc.) and user account parameters, to the factory default settings. • Factory Defaults: Restore all parameters to the factory default settings. • Restore to Inactive: Restore the device to inactive status. 3. Click OK to restore the default settings.
DS-720xHTI-Kx DVR User Manual Chapter 15 Others 15.1 Configuring General Settings Purpose You can configure the output resolution, system time, mouse pointer speed, etc. 1. Go to Menu > System Configuration > General > Display. Figure 15-1 General Settings Interface (for Other Models)) 2. Configure the following settings: • Language: The default language used is English. • Output Standard: Select the output standard to be PAL or NTSC.
DS-720xHTI-Kx DVR User Manual 15.2 Configuring DST Settings 1. Go to Menu > System Configuration > General > Time/Date. 2. Check the Enable DST checkbox. 3. Click Customize. Figure 15-2 DST Settings Interface 4. Check the Auto DST Adjustment checkbox, or manually set the date of the DST period. 15.3 Configuring More Settings 1. Go to Menu > System Configuration > General > More Settings. Figure 15-3 More Settings Interface 2. Configure the following settings: • Device Name: Edit the name of DVR.
DS-720xHTI-Kx DVR User Manual • Auto Logout: Set timeout time for menu inactivity. E.g., when the timeout time is set to 5 Minutes, then the system will exit from the current operation menu to live view screen after five minutes of menu inactivity. • Enable HDMI/VGA Simultaneous Output: Causes the HDMI monitor and the VGA monitor to display the same (main) image. • Menu Output Mode: You can choose the menu display on different video output. Auto and HDMI/VGA are selectable. 3.
DS-720xHTI-Kx DVR User Manual Figure 15-5 Add User Menu 3. Enter the information for new user, including User Name, Password, Confirm, Level, User’s IP Address, and User’s MAC Address. • Password: Set the password for the user account. STRONG PASSWORD RECOMMENDED – We highly recommend you create a strong password of your own choosing (using a minimum of eight characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters).
DS-720xHTI-Kx DVR User Manual Figure 15-6 Added User Listed in User Management Interface 5. You can assign permissions for the added user. 1) Select the user from the list and then click shown below. to enter the Permission Settings interface, as Figure 15-7 User Permission Settings Interface 2) Set the operating permission of Local Configuration, Remote Configuration, and Camera Configuration for the user.
DS-720xHTI-Kx DVR User Manual • • Remote Configuration ˗ Remote Log Search: Remotely viewing logs that are saved on the device. ˗ Remote Parameters Settings: Remotely configuring parameters, restoring factory default parameters, and importing/exporting configuration files. ˗ Remote Camera Management: Remotely enabling and disabling analog camera(s), and adding, deleting, and editing network camera(s). This function is supported by HDVR series.
DS-720xHTI-Kx DVR User Manual Figure 15-8 User List 3. Click to delete the selected user account. 15.4.3 Editing a User Purpose For the added user accounts, you can edit the parameters. 1. Go to Menu > System Configuration > User. 2. Select the user to be edited from the list. 3. Click the icon to enter the Edit User interface, as shown below.
DS-720xHTI-Kx DVR User Manual 4. Edit the corresponding parameters. • Operator and Guest You can edit the user information, including user name, password, permission level, and MAC address. Check the Change Password checkbox to change the password, and input the new password in the Password and Confirm text field. A strong password is recommended. • Admin You are allowed only to edit the password and MAC address.
DS-720xHTI-Kx DVR User Manual Figure 15-10 Set Unlock Pattern for Admin User 6. (Optional) Click the icon after Draw Unlock Pattern to modify the pattern. 7. (Optional) Click the icon after Export GUID to pop up the Reset Password interface. Click Export to export the GUID (Globally Unique Identifier; a file generated, exported, and saved to reset the user’s password) to the USB flash drive for retrieving the forgotten password. Then a GUID file will be saved in the USB flash drive.
DS-720xHTI-Kx DVR User Manual Chapter 16 Appendix 16.
DS-720xHTI-Kx DVR User Manual 16.2 Glossary • Dual-Stream: Dual-stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 1080P and the sub-stream having a maximum resolution of CIF. • DVR: Acronym for Digital Video Recorder.
DS-720xHTI-Kx DVR User Manual 16.3 Troubleshooting • No image displayed on the monitor after the device is starting up normally. Possible Reasons: — No VGA or HDMI connections. — Connection cable is damaged. — Input mode of the monitor is incorrect. Step 1 Verify the device is connected with the monitor via HDMI or VGA cable. If not, please connect the device with the monitor and reboot. Step 2 Verify the connection cable is good.
DS-720xHTI-Kx DVR User Manual 2) Step 3 If the status of the HDD is “Uninitialized,” check the checkbox of the corresponding HDD and click Init. Verify the HDD is detected or is in good condition. 1) Select Menu > System Configuration > HDD > General. 2) If the HDD is not detected or the status is “Abnormal,” replace the dedicated HDD according to the requirement. Step 4 Check if the fault is solved by the step 1 to step 3. 1) If it is solved, finish the process.
DS-720xHTI-Kx DVR User Manual If not, contact an engineer from our company further process. • The image gets stuck when DVR is playing back by single or multi-channel cameras. Possible Reasons: — The frame rate is not the real-time frame rate. — The DVR supports up to 16-channel synchronize playback at the resolution of 4CIF, if you want a 16-channel synchronize playback at the resolution of 720p, the frame extracting may occur, which leads to a slight stuck.
DS-720xHTI-Kx DVR User Manual Step 4 Check if the fault is solved by the above steps. If it is solved, finish the process. If not, contact an engineer from our company for further process. 16.4 Compatible Hikvision IP Cameras Type Model Version HD Network Camera DS-2CD7153-E DS-2CD754F-EI DS-2CD783F-EI DS-2CD7164-E DS-2CD864FWD-E DS-2CD4026FWD 14.33 DS-2CD6233F 14.24 DS-2CD2012-I DS-2CD4012F DS-2CD4232FWD-I V5.1.0 build 131202 V5.1.0 build 131202 V5.1.0 build 131202 V5.1.0 build 131202 V5.1.
DS-720xHTI-Kx DVR User Manual 16.6 Applicable Power Adapters Use only power supplies listed in the user instructions. Power Adapter Model Specifications MSA-C1500IC12.0-18P-DE 12 V, 1.5 A ADS-25FSG-12 12018GPG CE, 100 to 240 VAC, 12 V, 1.5 A, 18 W, Φ5.5 × 2.1 × 10 MSA-C1500IC12.0-18P-US 12 V, 1.5 A TS-A018-120015AD 100 to 240 VAC, 12 V, 1.5 A, 18 W, Φ5.5 × 2.1 × 10 MSA-C2000IC12.0-24P-DE 12 V, 2 A ADS-24S-12 1224GPG CE, 100 to 240 VAC, 12 V, 2 A, 24 W, Φ2.1 MSA-C2000IC12.
DS-720xHTI-Kx DVR User Manual 187
