User Manual
Table Of Contents
- Chapter 1 Introduction
- Chapter 2 Structure
- Chapter 3 Network Parameters Configuration
- Chapter 4 Access to DS-6700 by Client Software
- Chapter 5 Access to DS-6700 by WEB Browser
- Chapter 6 Live View
- Chapter 7 Device Configuration
- 7.1 Local Configuration
- 7.2 Configuring Time Settings
- 7.3 Network Settings
- 7.3.1 Configuring TCP/IP Settings
- 7.3.2 Configuring Port Settings
- 7.3.3 Configuring DDNS Settings
- 7.3.4 Configuring PPPoE Settings
- 7.3.5 Configuring Email Settings
- 7.3.6 Adding Network Disk
- 7.3.7 Configuring SNMP Settings
- 7.3.8 Configuring QoS Settings
- 7.3.9 Configuring FTP Settings
- 7.3.10 Configuring SOCKS Settings
- 7.3.11 Configuring UPnPTM Settings
- 7.3.12 Configuring HTTPS Settings
- 7.3.13 Configuring Bonjour Settings
- 7.3.14 Configuring IP Address Filter
- 7.3.15 Configuring Multicast Address
- Chapter 8 Camera Settings
- Chapter 9 Record/Capture Settings
- Chapter 10 Playback
- Chapter 11 Managing User Accounts
- Chapter 12 Log Search and Maintenance
- Chapter 13 FAQ
User Manual of DS-6700 Series Audio/Video Encoder
14
Table 2.6 Rear Panel of DS-6708HWI/HFI (-SATA)
Item
Description
1
VIDEO IN
BNC connectors for video input.
2
LINE IN
3.5mm two-way audio input interface; connect to active pick-up,
microphone, etc.
3
AUDIO OUT
3.5mm audio output interface; connect to audio output device, e.g.,
loudspeaker, etc.
4
AUDIO IN
Line input interface for audio input.
5
LAN
10M/100/1000Mbps adaptive Ethernet interface.
6
RESET
Restore the factory default settings by holding the RESET button for
more than 15 seconds after the device is turned on.
7
RS-232,
RS-485
RS-232 serial interface for configuration of device’s parameters or
used as transparent channel; RS-485 serial interface for connection to
pan/tilt unit, speed dome, etc.
8
ALARM IN
Relay alarm input.
9
ALARM
OUT
Relay alarm output.
10
DC12V
12V DC power supply.
11
GND
Grounding
DS-6716HWI / HFI (-SATA):
Figure 2.8 Rear Panel of DS-6716HWI/HFI (-SATA)
Table 2.7 Rear Panel of DS-6716HWI/HFI (-SATA)
Item
Description
1
VIDEO IN
BNC connectors for video input.
2
LINE IN
3.5mm two-way audio interface; connect to active pick-up,
microphone, etc.
3
AUDIO OUT
3.5mm audio output interface; connect to audio output device, e.g.,
loudspeaker, etc.
4
AUDIO IN
Line input interface for audio input.
5
LAN
10M/100/1000Mbps adaptive Ethernet interface.
6
RESET
Restore the factory default settings by holding the RESET button for
more than 15 seconds after power is turned on.
7
RS-232,
RS-485
RS-232 serial interface for configuration of device’s parameters or
used as transparent channel; RS-485 serial interface for connection to
pan/tilt unit, speed dome, etc.
8
ALARM IN
Relay alarm input.
9
ALARM
OUT
Relay alarm output.
10
DC12V
12V DC power supply.
11
GND
Grounding