Quick Start Guide

2
3
4
5
Device Connecon
Connect your devices according to your actual networking requirements.
Interfaces
Rear Panel
Front Panel
Packing List
1
Switch x 1
Quick Start
Guide x 1
Power Cord x 1
Hi-
PoE Port
Hi-PoE port is used for other Hi-PoE PTZ cameras connecon, and
the max. power is 60 W.
PoE Ports
100 Mbps PoE ports are used for other PoE devices connecon.
RJ45 Ports
1000 Mbps RJ45 ports are used for devices connecon via network
cables.
LINK/ACT
Indicator
PoE
Indicator
PoE-MAX Indicator
PWR
Indicator
PoE Ports
RJ45 Ports
Grounding
Terminal
Power
Supply
LINK/ACT
Indicator
Power Adapter x 1
Applicable Models
This manual is applicable to DS-3E0310HP series 100 Mbps Long-Range PoE switch.
Symbol Convenons
The symbols that may be found in this document are defined as follows.
During the installaon and ulizaon of the device, please strictly conform to electrical
safety rules in different naons and regions.
Use the aached power adaptor only and not to change the adaptor randomly. Please
refer to specificaon table for specific requirements of power adaptor.
Never aempt to disassemble the device yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
The device must be installed in machine room only, and only maintenance staff or
qualified person should access to the device.
Do not touch the upper cover area of the device that may be overheated.
Power must be shut down during cable connecon, device installaon and
dismantlement.
You shall acknowledge that the use of the device with Internet access might be under
network security risks, please strengthen protecon for your personal informaon and
data security. If you find the device might be under network security risks, please contact
with us.
Proper configuraon of all passports and other security sengs is the responsibility of
the installer, and you shall keep user name and passports properly.
Please keep all original packing materials properly. If the product does not work properly,
pack the switch in its original packing materials for shipping. We shall not assume any
responsibility for damages caused by improper packing materials during shipping.
Ensure that your devices powered via the PoE port have their shells protected and
fire-proofed, because the switches are not compliant with the Limited Power Source
(LPS) standard.
This is a class A product and may cause radio interference in which case the user may be
required to take adequate measures.
Indicates a hazard with a high level of risk, which if
not avoided, will result in death or serious injury.
Symbol Descripon
Provides addional informaon to emphasize or
supplement important points of the main text.
Indicates a potenally hazardous situaon, which if not
avoided, could result in equipment damage, data loss,
performance degradaon, or unexpected results.
•
•
•
•
•
•
•
•
•
•
•
DIP Switch
ON: Extend mode, ports 1-8 support network transmission of up to
300 m, and the speed rate of the port is 10 Mbps.
OFF: Standard mode, the network transmission of PoE ports is up to
100 m, and the speed rate of the port is 100 Mbps.
Grounding Terminal
The grounding terminal is used to connect to the ground cable to
protect the switch from lightning.
Power Supply
Use the aached power cord to connect the switch to socket.
If any accessories are damaged or lost, keep the package intact
and contact your dealer for replacement.
DIP Switch
Hi-PoE PoE UPLINK
OFF ON
Extend
PORT 1-8
DC 48V
PWR
Data
Power+Data(PoE)
Internet
Router
NVR
Dual uplink ports for
CCTV scenario
Up to 300 meters
(Port 1-8)
6 KV Surge Protection
8-Port 10/100M PoE
10/100M Unmanaged PoE Pro-Series
IP Camera
Hi-PoE PTZ
(port 1)
802.3bt Hi-PoE