Network Covert Camera Quick Start Guide 0
Network Covert Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Covert Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Covert Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Covert Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Covert Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Covert Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
Network Covert Camera·Quick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Network Covert Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 1.1 General Appearance...................................................... 10 1.1.1 Type I Camera General Appearance .................... 10 1.1.2 Type II Camera General Appearance ................... 12 1.1.3 Type III Camera General Appearance .................. 13 1.2 Front Panel .................................................................... 15 1.2.
Network Covert Camera·Quick Start Guide 2.5.2 Mounting with a Incline Bracket ......................... 53 3 Activate and Access Network Camera ..........................................
Network Covert Camera·Quick Start Guide 1 Appearance Description 1.1 General Appearance There are two covert camera types, the general appearance of the covert camera is shown below: 1.1.
Network Covert Camera·Quick Start Guide Table 1-1 Description of the Type I Camera No. Description 1 Main unit 2 Mounting rail 3 Rear panel 4 Front panel 5 POWER Indicator LED 6 STATUS Indicator LED 7 LINK Indicator LED Solid red: Power-on Unlit: Power-off Solid green: The camera works properly. Unlit: The camera does not work properly. Flashing amber: Network properly connected. Unlit: Network disconnected.
Network Covert Camera·Quick Start Guide 1.1.2 Type II Camera General Appearance 2 3 4 1 Figure 1-2 Type II Camera General Appearance Table 1-2 Description of the General Appearance No.
Network Covert Camera·Quick Start Guide 1.1.3 Type III Camera General Appearance 2 3 4 1 Figure 1-3 Type III Camera General Appearance Table 1-3 Description of the General Appearance No. Description 1 Main unit 2 POWER Indicator LED 3 STATUS Indicator LED Solid red: Power-on Unlit: Power-off Solid green: The camera works properly. Unlit: The camera does not work properly.
Network Covert Camera·Quick Start Guide No. 4 Description LINK Indicator LED Flashing amber: Network properly connected. Unlit: Network disconnected.
Network Covert Camera·Quick Start Guide 1.2 Front Panel 1.2.1 Type I Covert Camera Front Panel The Type I covert camera equips with three types of front panel, as shown in Figure 1-4, Figure 1-5, and Figure 1-6.
Network Covert Camera·Quick Start Guide 3 1 2 AUDIO IN AUDIO OUT 4 VIN1 VIN2 SD Figure 1-6 The Type C Front Panel Table 1-4 Description of the Front Panel No.
Network Covert Camera·Quick Start Guide 1.2.2 Type II Covert Camera Front Panel 1 2 3 Figure 1-7 Type II Camera Front Panel Table 1-5 Description of the Front Panel No.
Network Covert Camera·Quick Start Guide 1.2.3 Type III Covert Camera Front Panel The front panel of the Type III covert camera is shown in Figure 1-8. 1 2 3 Figure 1-8 The Type B Front Panel Table 1-6 Description of the Front Panel No.
Network Covert Camera·Quick Start Guide 1.3 Rear Panel 1.3.1 Type I Covert Camera Rear Panel The rear panel of the Type I covert camera is shown in Figure 1-9. 1 2 LAN(PoE) RXD TXD GND IN1 1B 1A 3 ALARM RS232 DC 12V RESET 4 Figure 1-9 Type I Covert Camera Rear Panel Table 1-7 Description of the Type I Covert Camera Rear Panel No.
Network Covert Camera·Quick Start Guide 1.3.2 Type II Covert Camera Rear Panel The rear panel of the Type II covert camera is shown in Figure 1-10.
Network Covert Camera·Quick Start Guide 1.3.3 Type III Covert Camera Rear Panel The rear panel of the Type III covert camera is shown in Figure 1-11. 1 2 3 Figure 1-11 Type II Covert Camera Rear Panel Table 1-8 Description of the Covert Camera Rear Panel No.
Network Covert Camera·Quick Start Guide 1.4 Sensor Units The different covert camera model is equipped with four different types of sensor unit, including block-shaped sensor unit, cylindrical sensor unit, tube lens and ball-shaped sensor unit. Type I: Block-Shaped Sensor Unit 2 1 4 3 Figure 1-12 Block-Shaped Sensor Unit Table 1-9 Description of the Block-Shaped Sensor Unit No.
Network Covert Camera·Quick Start Guide Type II: Cylindrical Sensor Unit 1 3 2 Figure 1-13 Cylindrical Sensor Unit Table 1-10 Description of the Block-Shaped Sensor Unit No.
Network Covert Camera·Quick Start Guide Type III: Tube Lens 1 2 3 Figure 1-14 Tube Lens Table 1-11 Description of the Tube Lens No.
Network Covert Camera·Quick Start Guide Type IV: Ball-Shaped Sensor Unit The ball-shaped sensor unit has two models with different communication interfaces, the RJ-12 interface and M12 interface.
Network Covert Camera·Quick Start Guide Table 1-12 Description of Ball-Shaped Sensor Unit No.
Network Covert Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 V DC or 24 V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Covert Camera·Quick Start Guide Figure 2-1 Secure the Mounting Rail Secure the bracket on the rear surface of the main unit with corresponding screws. Figure 2-2 Secure Bracket onto Main Unit Do not upside down the main unit when you fasten the bracket. Hang the main unit together with the bracket to the mounting rail and complete the installation.
Network Covert Camera·Quick Start Guide Figure 2-3 Hang the Main Unit 2.1.2 Installing Type II Covert Camera Unit Steps: 1. Secure the mounting rail onto the installation surface with the supplied PA3 × 25 screws. Figure 2-4 Secure the Mounting Rail 2. Secure the bracket on the rear surface of the main unit with corresponding screws.
Network Covert Camera·Quick Start Guide Figure 2-5 Secure Bracket onto Main Unit Do not upside down the main unit when you fasten the bracket. 3. Hang the main unit together with the bracket to the mounting rail and complete the installation. 2.1.3 Installing Type III Covert Camera Unit Steps: 1. Secure the bracket on the rear surface of the main unit with four M2*5 screws.
Network Covert Camera·Quick Start Guide Main Unit Bracket Figure 2-6 Secure Bracket onto Main Unit 2. Secure the bracket onto the installation surface with the supplied screws.
Network Covert Camera·Quick Start Guide 2.2 Installing the Block-Shaped Sensor Unit This series of camera support concealed mounting and exposed mounting with a decorative cover. 2.2.1 Concealed Mounting Please make sure that the mounting surface is suitable for adhesive pasting. Steps: 1. Drill on the mounting surface, as shown in Figure 2-8. Drill on the Surface Make sure the drilling hole is big enough for the camera lens. 2. Remove a side of the adhesive tape on the bracket.
Network Covert Camera·Quick Start Guide Paste the Bracket 3. Install the block-shaped sensor unit into the bracket and make it to be buckled. 4. Tighten the fastening screw on the top of the bracket.
Network Covert Camera·Quick Start Guide 2.2.2 Exposed Mounting Steps: Fix the Block-shaped sensor unit on the mounting surface with screws, as shown in Figure 2-11. Fix the Block-shaped Sensor Unit For cement surface mounting, you need to use the expansion screw to fix the camera. For wooden surface mounting, you can just use the self-tapping screw to fix the camera.
Network Covert Camera·Quick Start Guide 5. Shield the sensor unit with the decorative cover. As shown in Figure 2-12. Hood the Cover 2.2.3 Mounting with Pole-Shaped Bracket If you purchase the camera with a pole-shaped mounting bracket, follow the steps to complete installation of the lens and the bracket.
Network Covert Camera·Quick Start Guide Steps: 1. Fit the lens and the lens cable into the lens bracket as shown below. Lens Bracket Lens Cable Fit Lens and Lens Cable into Lens Bracket 2. Make a mark at a height of 1.83m (6ft.) on wall (or other desired mounting position). Align the “1.83m (6ft.)” sticker on base with the mark on wall. Then, mark the first expansion screw hole as shown in the figure below.
Network Covert Camera·Quick Start Guide 1.83m (6ft) 1.83m (6ft) 1.83m (6ft) Marking for Installation 3. Install the first expansion screw loosely and hang the bracket base on the screw.
Network Covert Camera·Quick Start Guide First Expansion Screw 1.83m (6ft) Hang the Bracket Base 4. Plan and prepare cable routing. This bracket supports cable routing through wall and on surface, select one way according to your actual needs. 1). If you choose to route cable through wall, drill a cable hole according to the size and height of cable hole on the base. See Figure 2-17. 2). If you choose to route cable on surface, make a cable hole on the top or bottom cover. See Figure 2-17.
Network Covert Camera·Quick Start Guide 1.83m (6ft) Cable Hole Cable Holes Route cable on surface Route cable through wall Plan Cable Routing 5. Route cable and fit the lens bracket into the base. Use a screw to secure the lens bracket. See Figure 2-18.
Network Covert Camera·Quick Start Guide or Install and Secure Lens Bracket 6. Loosely screw the thumbscrew to the base. Adjust the panning position of the lens, and tighten the thumbscrew.
Network Covert Camera·Quick Start Guide 7. Screw the top cover to the base. Top Cover 1.83m (6ft) 1.83m (6ft) Install Top Cover 8. Install the second expansion screw. Tighten the first expansion screw. See Figure 2-21. 9. Peel off protective films on both side of the decorative cover. Slide the decorative cover in the base. See Figure 2-22.
Network Covert Camera·Quick Start Guide 1.
Network Covert Camera·Quick Start Guide 10. Screw the bottom cover to the base. Bottom Cover Install Bottom Cover Installing the Cylindrical Sensor Unit This series of camera only support concealed mounting. Please make sure that the mounting surface is suitable for adhesive pasting. Steps: 1. Drill on the mounting surface, as shown in Figure 2-24.
Network Covert Camera·Quick Start Guide Drill on the Surface Make sure that the drilling hole is big enough for the camera lens. 2. Remove a side of the adhesive tape on the bracket. Paste the bracket on the mounting surface with aligning with the drilling hole. As shown in figure below. Paste the Bracket 3. Install the cylindrical sensor into the mounting hole in the round rail bracket.
Network Covert Camera·Quick Start Guide 4. Turn the locking sleeve to fix the sensor. Install the Cylindrical Sensor Installing the Tube Lens Steps: 1. Fix the mounting base of the bracket to the ceiling with the supplied screws.
Network Covert Camera·Quick Start Guide 2. Hood the bracket cover to the mounting base. Hood the Bracket Cover 3. Screw the bracket to the mounting base.
Network Covert Camera·Quick Start Guide Another shorter bracket is also selectable; please select the bracket according to your demand. 4. Loop the tube lens with the loop of the bracket, and tighten it with the supplied screw. As shown in Figure 2-30. Loop the Tube Lens 5. Align the assembled tube lens to the bracket, and rotate the lens to tighten the lens with the bracket.
Network Covert Camera·Quick Start Guide Install the Tube Lens to the Bracket 6. Loosen the knob to adjust the surveillance angle, and then tighten the lock nut to complete the installation.
Network Covert Camera·Quick Start Guide 2.5 Installing the Ball-Shaped Sensor Unit 2.5.1 Mounting with the Included Bracket Steps: 1. Paste the drill template to the desired mounting place. Drill two screw holes and a hole for routing cable according to the drill template. Figure 2-33 Drill Template 2. Route the camera cable through the mounting base of the included bracket. Fixed the mounting base to the wall or ceiling.
Network Covert Camera·Quick Start Guide Ceiling Mounting Base Cable Hole Screws Wall Mounting Base Cable Hole Screws Figure 2-34 Fix the Mounting Bracket on Ceiling or on Wall 3. Place the camera in the bracket cover.
Network Covert Camera·Quick Start Guide 4. Get the wedge on the bracket cover stuck in the slot of the mounting base, close the cover, and screw the bracket cover on the mounting base loosely.
Network Covert Camera·Quick Start Guide 5. Adjust the surveillance angle. 3). Stick the supplied plastic ring in the camera 4). Connect the cables and power on the camera to view the image. 5). Hold and move the plastic ring to adjust the panning, tilting, and rotating position to desired place. Rotate: 0° to 360° Tilt: -16.5° to 16.5° or -21.5° to 21.5° Notch Camera Notch Pan: -16.5° to 16.5° or -21.5° to 21.5° Plastic Ring Figure 2-37 Adjust the View Angle 6).
Network Covert Camera·Quick Start Guide 6. Tighten the screw on the bracket cover. Ceiling Screw Wall Screw Figure 2-38 Tighten the Screw 2.5.2 Mounting with a Incline Bracket Before you start: There is no incline bracket included in the package. If you choose this mounting type, you need to provide a bracket before starting. The shown bracket below is only for demonstration. Steps: 1. Paste the drill template to the desired mounting place.
Network Covert Camera·Quick Start Guide Figure 2-39 Drill Template 2. Route the camera cable through the mounting base of the incline bracket. And fix the camera to the mounting base with the fixing ring and screw. The screw should be installed loosely to leave some space for view angle adjustment.
Network Covert Camera·Quick Start Guide Mounting Base Camera Fixing Ring Screw Figure 2-40 Fix the Camera to Mounting Base 3. Install the incline bracket with camera on the wall or ceiling with supplied screws. Cable Hole Ceiling Wall Cable Hole Screws Screws Figure 2-41 Fix the Camera and Mounting Base to Wall or Ceiling 4. Adjust view angle of the camera. Refer to Step 5 in Section 2.5.1.
Network Covert Camera·Quick Start Guide 5. Tighten the screw on fixing ring. 6. Install the incline bracket cover.
Network Covert Camera·Quick Start Guide 3 Activate and Access Network Camera Scan the QR code to get Activate and Access Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
UD09899B 0505001080816 0
