Fisheye Network Camera Quick Start Guide COPYRIGHT © 2019 Hikvision.
Quick Start Guide ALL RIGHTS RESERVED Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Laws and Regulations The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations. Transportation Keep the device in original or similar packaging while transporting it. Power Supply The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra Low Voltage) and the Limited Power Source.
Maintenance If the product does not work properly, please contact your dealer or the nearest service center. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details. Cleaning Please use a soft and dry cloth when clean inside and outside surfaces of the product cover.
Emergency If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center. Time Synchronization Set up camera time manually for the first time access if the local time is not synchronized with that of the network. Visit the camera via Web browse/client software and go to time settings interface. Installation Make sure the device is firmly secured to any wall or ceiling mountings.
Symbols and Marks Notice Warning Forbidden Correct Incorrect Turn to page A and continue. i. Not necessarily included accessory. ii. Variable accessory amount. iii. Skip this step if not required.
Other situations omitted Waterproof Skip this step if not necessary
1
* 1x 1x 1x T20 T10 1x* 2x* PSFUNC10-24x22.
1.
PA4x25 PSFUNC10-24x22.5 2.1-2.8 PA4x35 3.1-3.
2.1 A.1-A.4 B.1-B.
A.1 A.
A.3 A.4 PA4x25 2.2 5.
B.1 B.2 PA4x25 2.2 5.
A.4 B.2 2.2 T20 PSFUNC10-24x22.
2.3 5.
2.
2.
13
2.6 A B 2.7 2.
2.7 T20 2.
3.
A B 3.2 5.
3.
3.
20
3.5 A B 3.6 3.
3.6 PA4x35 5.0 3.
Memory Card Slot Reset Button Network Interface Power Interface Alarm Interface 23
Memory Card Slot Reset Button Network Interface Power Interface 24
Memory Card Slot Reset Button Aviation Plug Interface MOLEX Interface 25
Memory Card Slot Reset Button Aviation Plug Interface 26
Activate and Access Network Camera Scan the QR code to get Activate and Access Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
Reset and Restore Camera Press Reset button for about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. For the position of the reset button, refer to the figure in the installation page.
UD14593B
