User Manual
Table Of Contents
- About this Manual
- Trademarks
- Disclaimer
- Symbol Conventions
- Safety Instruction
- Laws and Regulations
- Transportation
- Power Supply
- Battery
- Maintenance
- Usage Environment
- Emergency
- Manufacturer Address
- Chapter 1 Overview
- Chapter 2 Device Activation and Accessing
- Chapter 3 Temperature Measurement
- Chapter 4 Fire Source Detection
- Fire Detection
- Smoking Detection
- 4
- 4.1 Select Recommended Scene
- 4.2 Set Fire Detection Parameters
- Before You Start
- Steps
- Fire Source Detection Mode
- 1) Go to Configuration → Event → Smart Event → Fire Source Detection Shield.
- 2) Check Enable Fire Source Detection Shield.
- 3) Click Draw Area and drag the mouse in the live view to draw the area. Release the mouse to finish drawing.
- 4) You can drag the corners of the red rectangle area to change its shape and size, or drag the rectangle to the position on demand.
- 5) Click Stop Drawing.
- 6) Click Clear All to clear all of the setting areas.
- 7) Set the value of Active Zoom Ratio on demand, and then the shield will appear only when the zoom ratio is greater than the predefined value
- 8) Click Add to save the smoke detection shield, and it will be listed in the Fire Source Detection Shield List area; you can select a region and click Delete to delete it from the list; you can also define the color of the regions.
- 9) Check Display Shield Region to show the shielded area in live view.
- Chapter 5 Behavior Analysis
- Chapter 6 Event and Alarm
- Chapter 7 Arming Schedule and Alarm Linkage
- 7
- 7.1 Set Arming Schedule
- 7.2 Linkage Method Settings
- 7
- 7.1
- 7.2
- 7.2.1 Trigger Alarm Output
- 7.2.2 FTP/NAS/Memory Card Uploading
- 7.2.3 Send Email
- Set Email
- Before You Start
- Steps
- 1) Input the sender’s e-mail information, including Sender's Address, SMTP Server, and SMTP Port.
- 2) Optional: If your e-mail server requires authentication, check Authentication and input your user name and password to log in to the server.
- 3) Set the E-mail Encryption.
- 4) Optional: If you want to receive notification with alarm pictures, check Attached Image.The notification e-mail has three attached alarm pictures about the event with configurable image capturing interval.
- 5) Input the receiver’s information, including the receiver’s name and address.
- 6) Click Test to see if the function is properly configured.
- 7.2.4 Notify Surveillance Center
- 7.2.5 Trigger Recording
- 7.2.6 Set Audible Alarm Output
- 7.2.7 Set Flashing Alarm Light Output
- Chapter 8 Live View
- Chapter 9 Video and Audio
- 9
- 9.1 Video Settings
- 9.2 Display Settings
- 9
- 9.1
- 9.2
- 9.3 OSD
- 9.4 Set Privacy Mask
- 9.5 Overlay Picture
- 9.6 Set Manual DPC (Defective Pixel Correction)
- Chapter 10 Video Recording and Picture Capture
- Chapter 11 Network Settings
- Chapter 12 System and Security
- 12
- 12.1 View Device Information
- 12.2 Search and Manage Log
- 12.3 Import and Export Configuration File
- Steps
- 1) Go to Configuration → System → Maintenance → Upgrade & Maintenance.
- 2) Click Device Parameters and input the encryption password to export the current configuration file.
- 3) Set the saving path to save the configuration file in a local computer.
- 1) Access the device that needs to be configured via a Web browser.
- 2) Click Browse to select the saved configuration file.
- 3) Input the encryption password you set when exporting the configuration file.
- 4) Click Import.
- Steps
- 12.4 Export Diagnose Information
- 12.5 Reboot
- 12.6 Restore and Default
- 12.7 Upgrade
- 12.8 View Open Source Software License
- 12.9 Time and Date
- 12.10 Set RS-232
- 12.11 Set RS-485
- 12.12 Set Same Unit
- 12.13 Security
- 12.14 User and Account
- Chapter 13 Appendix
DS-2TD2137-7P Thermal Network Camera User Manual
UM DS-2TD2137-7P 042021NA 8
10.1.3 Set FTP ................................................................................................................................. 49
10.1.4 Set Cloud Storage ................................................................................................................ 49
10.2 Video Recording ................................................................................................................................. 50
10.2.1 Record Automatically .......................................................................................................... 50
10.2.2 Record Manually .................................................................................................................. 51
10.2.3 Playback and Download Video ............................................................................................ 51
10.3 Capture Configuration ........................................................................................................................ 52
10.3.1 Capture Automatically ........................................................................................................ 52
10.3.2 Capture Manually ................................................................................................................. 52
10.3.3 View and Download Picture ................................................................................................ 52
Chapter 11 Network Settings ......................................................................................................................... 54
11.1 TCP/IP.................................................................................................................................................. 54
11.1.1 Multicast Discovery ............................................................................................................. 54
11.2 Port ...................................................................................................................................................... 55
11.3 Port Mapping ....................................................................................................................................... 55
11.3.1 Set Auto Port Mapping ........................................................................................................ 55
11.3.2 Set Manual Port Mapping .................................................................................................... 56
11.4 Multicast ............................................................................................................................................. 56
11.5 SNMP ................................................................................................................................................... 56
11.6 Access to Device via Domain Name .................................................................................................. 57
11.7 Access to Device via PPPoE Dial Up Connection ............................................................................... 57
11.8 Enable Hik-Connect Service on Camera............................................................................................ 58
11.8.1 Enable Hik-Connect Service via Web Browser ................................................................... 58
11.8.2 Enable Hik-Connect Service via SADP Software ................................................................ 58
11.8.3 Access Camera via Hik-Connect ........................................................................................ 59
11.9 Set ISUP ............................................................................................................................................... 59
11.10 Set ONVIF ............................................................................................................................................. 60
11.11 Set HTTP Listening ............................................................................................................................. 60
Chapter 12 System and Security.................................................................................................................... 61
12.1 View Device Information ..................................................................................................................... 61
12.2 Search and Manage Log..................................................................................................................... 61
12.3 Import and Export Configuration File ................................................................................................. 61
12.4 Export Diagnose Information ............................................................................................................. 62
12.5 Reboot ................................................................................................................................................ 62