User Manual
Table Of Contents
- About this Manual
- Trademarks
- Disclaimer
- Symbol Conventions
- Safety Instruction
- Laws and Regulations
- Transportation
- Power Supply
- Battery
- Maintenance
- Usage Environment
- Emergency
- Manufacturer Address
- Chapter 1 Overview
- Chapter 2 Device Activation and Accessing
- Chapter 3 Temperature Measurement
- Chapter 4 Fire Source Detection
- Fire Detection
- Smoking Detection
- 4
- 4.1 Select Recommended Scene
- 4.2 Set Fire Detection Parameters
- Before You Start
- Steps
- Fire Source Detection Mode
- 1) Go to Configuration → Event → Smart Event → Fire Source Detection Shield.
- 2) Check Enable Fire Source Detection Shield.
- 3) Click Draw Area and drag the mouse in the live view to draw the area. Release the mouse to finish drawing.
- 4) You can drag the corners of the red rectangle area to change its shape and size, or drag the rectangle to the position on demand.
- 5) Click Stop Drawing.
- 6) Click Clear All to clear all of the setting areas.
- 7) Set the value of Active Zoom Ratio on demand, and then the shield will appear only when the zoom ratio is greater than the predefined value
- 8) Click Add to save the smoke detection shield, and it will be listed in the Fire Source Detection Shield List area; you can select a region and click Delete to delete it from the list; you can also define the color of the regions.
- 9) Check Display Shield Region to show the shielded area in live view.
- Chapter 5 Behavior Analysis
- Chapter 6 Event and Alarm
- Chapter 7 Arming Schedule and Alarm Linkage
- 7
- 7.1 Set Arming Schedule
- 7.2 Linkage Method Settings
- 7
- 7.1
- 7.2
- 7.2.1 Trigger Alarm Output
- 7.2.2 FTP/NAS/Memory Card Uploading
- 7.2.3 Send Email
- Set Email
- Before You Start
- Steps
- 1) Input the sender’s e-mail information, including Sender's Address, SMTP Server, and SMTP Port.
- 2) Optional: If your e-mail server requires authentication, check Authentication and input your user name and password to log in to the server.
- 3) Set the E-mail Encryption.
- 4) Optional: If you want to receive notification with alarm pictures, check Attached Image.The notification e-mail has three attached alarm pictures about the event with configurable image capturing interval.
- 5) Input the receiver’s information, including the receiver’s name and address.
- 6) Click Test to see if the function is properly configured.
- 7.2.4 Notify Surveillance Center
- 7.2.5 Trigger Recording
- 7.2.6 Set Audible Alarm Output
- 7.2.7 Set Flashing Alarm Light Output
- Chapter 8 Live View
- Chapter 9 Video and Audio
- 9
- 9.1 Video Settings
- 9.2 Display Settings
- 9
- 9.1
- 9.2
- 9.3 OSD
- 9.4 Set Privacy Mask
- 9.5 Overlay Picture
- 9.6 Set Manual DPC (Defective Pixel Correction)
- Chapter 10 Video Recording and Picture Capture
- Chapter 11 Network Settings
- Chapter 12 System and Security
- 12
- 12.1 View Device Information
- 12.2 Search and Manage Log
- 12.3 Import and Export Configuration File
- Steps
- 1) Go to Configuration → System → Maintenance → Upgrade & Maintenance.
- 2) Click Device Parameters and input the encryption password to export the current configuration file.
- 3) Set the saving path to save the configuration file in a local computer.
- 1) Access the device that needs to be configured via a Web browser.
- 2) Click Browse to select the saved configuration file.
- 3) Input the encryption password you set when exporting the configuration file.
- 4) Click Import.
- Steps
- 12.4 Export Diagnose Information
- 12.5 Reboot
- 12.6 Restore and Default
- 12.7 Upgrade
- 12.8 View Open Source Software License
- 12.9 Time and Date
- 12.10 Set RS-232
- 12.11 Set RS-485
- 12.12 Set Same Unit
- 12.13 Security
- 12.14 User and Account
- Chapter 13 Appendix
DS-2TD2137-7P Thermal Network Camera User Manual
UM DS-2TD2137-7P 042021NA 5
Contents
Chapter 1 Overview ........................................................................................................................................ 10
1.1 Brief Description................................................................................................................................. 10
1.2 Functions............................................................................................................................................ 10
Chapter 2 Device Activation and Accessing .................................................................................................. 11
2.1 Activate the Device via SADP ............................................................................................................. 11
2.2 Activate the Device via Browser ........................................................................................................ 11
2.3 Login ................................................................................................................................................... 12
2.3.1 Install Plug-in ...................................................................................................................... 12
2.3.2 Illegal Login Lock ................................................................................................................ 12
Chapter 3 Temperature Measurement ............................................................................................................ 13
3.1 Notice .................................................................................................................................................. 13
3.2 Thermography Configuration Flow Chart .......................................................................................... 13
3.3 Automatic Thermography .................................................................................................................. 14
3.3.1 Set Thermography Parameters ........................................................................................... 14
3.3.2 Set Normal Mode ................................................................................................................. 15
3.3.3 Object Missing ..................................................................................................................... 15
3.3.4 Set Thermography Rule ....................................................................................................... 15
3.3.5 Point Thermography ............................................................................................................ 16
3.3.6 Line Thermography ............................................................................................................. 16
3.3.7 Area Thermography ............................................................................................................. 17
3.4 Set Shielded Region ........................................................................................................................... 17
3.5 Manual Thermography ....................................................................................................................... 17
Chapter 4 Fire Source Detection.................................................................................................................... 18
4.1 Select Recommended Scene ............................................................................................................ 18
4.2 Set Fire Detection Parameters ........................................................................................................... 18
Chapter 5 Behavior Analysis .......................................................................................................................... 20
5.1 Flow Chart of Behavior Analysis ........................................................................................................ 20
5.2 Set VCA Parameters ............................................................................................................................ 20
5.3 Calibration .......................................................................................................................................... 21
5.3.1 Calibrate Automatically ....................................................................................................... 21
5.3.2 Calibrate Manually ............................................................................................................... 22
5.3.3 Verify the Calibration Result ............................................................................................... 22