User Manual

ManualsBrandsHikvision ManualsDome Security Cameras5 Megapixel Outdoor IR HD-TVI/AHD/HD-CVI/CVBS Dome Camera, 2.7-13.5mm, Black

UM DS-2CE5xH0T-Axxxxx 042318NA 1

• DS-2CE56H0T-AVPIT3ZF

• DS-2CE56H0T-AITZF

• DS-2CE5AH0T-AVPIT3ZF

TurboHD

H0T Series Dome Camera

User Manual

Thank you for purchasing our product. If there are

any questions or requests, do not hesitate to contact

the dealer.

This manual applies to the models below:

Type

Model

Type I

Camera

2CE56H0T

VPIT3ZF

Type II Camera

2CE56H0T

ITZF

Type III Camera

2CE5AH0T

VPIT3ZF

Hikvision USA Inc., 18639 Railroad St., City of

Industry, CA 91748, USA • Hikvision Canada, 4848 rue

Levy, Saint Laurent, Quebec, Canada, H4R 2P1

Telephone: +1-909-895-0400 • Toll Free in USA: +1-

866-200-6690 • E-Mail: sales.usa@hikvision.com •

www.hikvision.com

Any and all information, including, among others,

wordings, pictures, graphs are the properties of

Hangzhou Hikvision Digital Technology Co., Ltd. or its

subsidiaries (hereinafter referred to be “Hikvision”).

This user manual (hereinafter referred to be “the

Manual”) cannot be reproduced, changed, translated,

or distributed, partially or wholly, by any means,

without the prior written permission of Hikvision.

Unless otherwise stipulated, Hikvision does not make

any warranties, guarantees or representations,

express or implied, regarding to the Manual.

This manual may contain technical or printing errors,

and the content is subject to change without notice.

Updates will be added to new versions of this

manual. We will readily improve or update the

products or procedures described in the manual.

Summary of content (16 pages)

PAGE 1
• DS-2CE56H0T-AVPIT3ZF • DS-2CE56H0T-AITZF • DS-2CE5AH0T-AVPIT3ZF TurboHD H0T Series Dome Camera User Manual Thank you for purchasing our product. If there are any questions or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Type I Camera Type II Camera Type III Camera Model DS-2CE56H0T-AVPIT3ZF DS-2CE56H0T-AITZF DS-2CE5AH0T-AVPIT3ZF Hikvision USA Inc., 18639 Railroad St.
PAGE 2
1 Preface 1.1 1.1.1 Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 3
1.1.4 Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. 1.1.5 Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions.” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
PAGE 4
• Do not place the camera in extremely hot, cold (the operating temperature shall be -40° to 60° C), dusty or damp locations, and do not expose it to high electromagnetic radiation. • If cleaning is necessary, use a clean cloth with a bit of ethanol, and wipe it gently. • Do not aim the camera at the sun or extra bright places. • The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the sensor surface will not be exposed to the laser beam.
PAGE 5
Note: To switch the video output, press and hold the switch button until the image turns black, then release. Cycle through available types to return to the default HD-TVI output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS. 2.2.2 Overview of Type II Camera Figure 2 Overview of Type II Camera Note: To switch the video output, press and hold the switch button until the image turns black, then release. Cycle through available types to return to the default HD-TVI output.
PAGE 6
• Make sure the wall is strong enough to withstand three times the weight of the camera and the mount. • If the wall is cement, insert expansion bolts before you install the camera. If the wall is wooden, use self-tapping screws to secure the camera. • If the product does not function properly, contact your dealer or the nearest service center. Do NOT disassemble the camera for repair or maintenance yourself. 3.
PAGE 7
• For a cement ceiling, expansion bolts are required to fix the camera. For a wooden ceiling, selftapping screws are required. 5. Route the cables through the cable hole or the side opening. 6. Align the camera with the back box/base plate, and tighten the screws to secure the camera with the back box/base plate. Figure 6 Fix the camera to the Ceiling 7. Connect the corresponding cables such as power cord and video cable. 8.
PAGE 8
Type I Camera Type II Camera Figure 8 Install Wall Mounting Mount 4. Refer to step 3 of 2.1 Ceiling Mounting of Type I and Type II Camera to remove dome camera’s bubble and the black liner. 5. Attach the dome camera back box/base plate to the wall mount and secure with supplied screws. Type I Camera Type II Camera Figure 9 Attach the Base Plate to the Mount 6. Route the cables through the mount. 7. Repeat steps 6 to 9 of the 2.1 Ceiling Mounting of Type I and Type II Camera to complete the installation.
PAGE 9
Figure 11 Remove the Bubble and the Black Liner 4. Attach the back box of the camera to the ceiling and secure with supplied screws. Figure 12 Attach the Back Box Note: The supplied screw package contains self-tapping screws and expansion bolts. For a cement ceiling, expansion bolts are required to fix the camera. For a wooden ceiling, self-tapping screws are required. 5. Route the cables through the cable hole or the side opening. 6. Connect the corresponding cables such as power cord and video cable.
PAGE 10
Figure 14 Fit the Black Liner Back 9. Tighten the screws on the dome camera bubble to finish the installation. Figure 15 Finish Installation 3.4 Type III Camera Wall Mounting Before you start: You must purchase a wall mount. Steps: 1. Drill four screw holes in the wall according to the holes of the mount. 2. Attach the mount to the wall by aligning the four screw holes of the mount with expansion screws on the wall. 3. Secure the mount with four hex nuts and washers. Figure 16 Install Wall Mount 4.
PAGE 11
Figure 17 Attach the Back Box to the Mount 6. Route the cables through the mount. 7. Repeat steps 6 to 9 of the 2.1 Ceiling Mounting of Type III Camera to complete the installation. 4 Menu Description Purpose: Call the menu by clicking the button on the PTZ Control interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR and the monitor, shown as figure 3-1. Figure 18 Connection 2. Power on the analog camera, TVI DVR, and the monitor to view the image on the monitor. 3.
PAGE 12
Figure 19 Main Menu Overview 5. Click the direction arrow to control the camera. a. Click up/down direction button to select the item. b. Click Iris + to confirm the selection. c. Click left/right direction button to adjust the value of the selected item. 4.1 VIDEO FORMAT You can set the video format to 5 MP @ 20 fps, 4 MP @ 25 fps, 4 MP @ 30 fps, 2 MP @ 25 fps, or 2 MP @ 30 fps. 4.2 EXPOSURE Exposure describes the brightness-related parameters, which can be adjusted by EXPOSURE MODE and AGC.
PAGE 13
Figure 20 EXPOSURE 4.3 EXPOSURE MODE You can set the EXPOSURE MODE to GLOBAL, BLC, or DWDR.  • GLOBAL GLOBAL refers to the normal exposure mode which performs exposure according to the whole image brightness. • BLC (Backlight Compensation) BLC (Backlight Compensation) compensates light for the front object to make it clear, but this may cause the over-exposure of the background, where the light is strong.
PAGE 14
Figure 21 B&W • IR LIGHT You can turn on/off the IR LIGHT to meet the requirements of different circumstances. • SMART IR The Smart IR function is used to adjust the light to its most suitable intensity and prevent the image from over exposure. The SMART IR value can be adjusted from 1 to 3. The higher the value, the more obvious the effects. 4.4.1 AUTO Automatically switch Color or BW (Black and White) according to actual scene brightness.
PAGE 15
• D→N Threshold (Day to Night Threshold) Day to Night Threshold is used to control the sensitivity of switching the day mode to the night mode. You can set the value from 1 to 9. The larger the value, the more sensitive the camera. • N→D Threshold (Night to Day Threshold) Night to Day Threshold is used to control the sensitivity of switching the night mode to the day mode. You can set the value from 1 to 9. The larger the value, the more sensitive the camera. 4.
PAGE 16
4.5.2 BRIGHTNESS Brightness refers to the brightness of the image. You can set the brightness value from 1 to 9 to darken or brighten the image. The higher the value, the brighter the image. 4.5.3 CONTRAST This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 9. 4.5.4 SHARPNESS Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 9. 4.5.