TURBO HD 2 MP Cube Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Model DS-2CE38D8T-PIR This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture.
1 Introduction 1.1 Product Features The camera is applicable for indoor conditions, and the application scenarios include office, store, living room, etc.. The main features are as follows: High performance CMOS sensor Low illumination, 0.005 Lux @ (F1.2, AGC ON), 0 Lux with IR IR cut filter with auto switch 120 dB true WDR PIR detection OSD menu with configurable parameters Auto white balance Internal synchronization SMART IR mode 1.2 Overview 1 2 5 3 4 6 7 8 9 Figure 1.
2 Installation 2.1 Installation Preparation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Check whether the power supply is matched with your required output to avoid damage.
Disassemble the 3-axis bracket. (1) Hold the base with one hand. (2) Rotate the pole anticlockwise to disassemble the pole from the base. Knob Pole Base Fixed Tray Disassemble the Bracket Install the fixed tray to the ceiling with supplied screws. Install the base to the fixed tray. Install the Mounting Base to the Fixed Tray Install the camera to the bracket. Install the Camera Connect the corresponding power cord, and video cable.
3 Menu Description Purpose: Call the menu by clicking icon on the PTZ Control interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Connection 2. Power on the analog camera, TVI DVR, and the monitor to view the image on the monitor. 3. Click PTZ Control to enter the PTZ Control interface. 4. Call the camera menu by clicking icon, or call preset No. 95.
3.2 LANGUAGE Supports English, and Chinese. 3.3 MAIN MENU 3.3.1 AE (AUTO EXPOSURE) Auto Exposure describes the brightness-related parameters, which can be adjusted by BRIGHTNESS, EXPOSURE MODE, AGC, and SENSE UP. EXPOSURE BRIGHTNESS EXPOSURE MODE AGC SENSE UP RETURN 5 GLOBAL MIDDLE 0 AE BRIGHTNESS Brightness refers to the brightness of the image. You can set the brightness value from 1 to 10 to darken or brighten the image. The higher the value, the brighter the image is.
ATW (Aoto Tracking White Balance) Under ATW mode, white balance is being adjusted automatically according to the color temperature of the scene illumination. MWB (Manual White Balance) You can set the R GAIN/B GAIN value from 1 to 255 to adjust the shades of red/blue color of the image. WB MWB 5 5 MODE R GAIN B GAIN RETURN MWB MODE 3.3.3 DAY NIGHT Color, BW (Black White), and AUTO are selectable for DAY and NIGHT switches. COLOR The image is colored in day mode all the time.
CONTRAST This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 10. SHARPNESS Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 10. COLOR GAIN Adjust this feature to change the saturation of the color. The value ranges from 1 to 10.
Select a MOTION area. Set the DISPLAY status as ON. Click the up/down/left/right button to define the position and size of the area. Set the SENSITIVITY from 0 to 100. CAMERA ID Edit the camera ID on this section. CAM ID SETTING MODE CAM ID X POSITION Y POSITION RETURN ON 75 36 16 CAM ID SETTING Set the MODE as on. Click up/don left/right button to choose the camera ID and the position. 3.3.6 RESET Reset all the settings to the default. 3.3.
