User Manual

5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position 0 ~ 360 .(° °)
.2).Tighten No.3 adjusting screw
3).Loosen the No.2 adjusting screw to adjust the
tilting position 0 ~ 90(° °).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image 0 ~ 360(° °).
.6).Tighten No.1 adjusting screw
Figure 2-3 3-axis Adjustment
Steps:
1.Drill the screw holes on the wall according to
the supplied drill template.
2.Attach the wall mount to the wall and tighten
the screws to fix it.
2.2 Wall Mounting for Type III
Camera
Figure 2-5 Drill Template & Install Mount
Figure 2-8 Angle Adjustment
5. Adjust the surveillance angle.
1). Loosen No.1 adjusting screw to adjust the pan
position (0 ~ 360 ).°°
2).Tighten No.1 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
tilting position(0 ~ 90 ).°°
4).Tighten No.2 adjusting screw.
4. Screw the mounting plate onto the camera.
1.Wiggle the mounting plate to disassemble it from
the wall mount.
5. Fix the camera to the wall mount with the
supplied screws.
Figure 2-6 Screw the Mounting Plate
Figure 2-4 Disassemble Mounting Plate
Mounting Plate
Mounting Plate
Figure 2-7 Fix the Camera
1
2
360°
90°
Figure 2-2 Fix the Camera to the Ceiling
Type I
Type II
3.2.2 WB
3.2.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the ,BRIGHTNESS EXPOSURE
MODE AGC, and .
:Brightness
Brightness refers to the brightness of the image.
Exposure Mode:
Move the cursor to , you can selectExposure Mode
the exposure mode between and .Globe BLC
When BLC is selected as the exposure mode, the
level of BLC mode can be adjusted, as shown in the
Figure 3-2.
3.2.4 VIDEO SETTING
Contrast:
Contrast enhances the difference in color and light
between parts of an image.
You can set the value from 1 to .
10
Sharpness:
Sharpness determines the amount of
detail that an imaging system can reproduce.
You can set the value from 1 to 10.
Saturation:
You can set the saturation level of the image. The
value is from 0 to 10.
DNR:
DNR decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp image quality. You can set the value from
0 to 7.
:Mirror
You can set the Mirror status as H, V, HV, or OFF.
3 Menu Operation
Figure 3-1 Main Menu
VIDEO
SETTING
DAY/NIGHT
WB
RESET
BRIGHTNESS
MODE
INFRARED
SMART IR
CONTRAST
SHARPNESS
SATURATION
EXIT
AE
DNR
MIRROR
EXPOSURE MODE
AGC
SAVE/EXIT
With a coaxial camera controller (purchase
separately) or calling the preset No.95 you can
select the menu and adjust the camera parameters.
3.1 FORMAT
You can set the format as PAL/NTSC.
3.2 SET UP
Move the cursor to , and press menu buttonSET UP
to enter the SET UP sub menu.
EXPOSURE
1.BRIGHTNESS
2.EXPOSURE MODE
LEVEL
3.AGC
4.RETURN
5
BLC
5
MIDDLE
Move the cursor to WB, and you can set White
Balance mode as and in this menuAWB MWB .
AWB: white balance is being adjusted
automatically.
: Set the value from 1 to 10.MWB R GAIN/B GAIN
As shown in Figure 3-3.
WB
MODE MWB
R GIAN 1-|--10
B GAIN 1-|--10
RETURN 8
AGC:
AGC optimizes the clarity of image in poor light
scene. AGC level can be set as OFF, LOW, MIDDLE
and HIGH.
Figure 3-2 EXPOSURE
Figure 3-3 WB
Figure 3-4 DAY/NIGHT
3.2.3 DAY & NIGHT
Move the cursor to DAY & NIGHT, and select
COLOR B/W SMART, , or as the DAY & NIGHT mode.
COLOR: The image is colored in day mode all the
time.
: The image is black & white all the time, andB/W
the IR LED turns on in the low-light conditions.
: Select to turn on/off the INFRARED_LAMPSMART
and to set the Smart IR level from 1to 16.
As shown in Figure 3-4.
DAY/NIGHT
MODE SMART
INFRARED OFF
SMART IR 0-|--5
RETURN 8
3.2.7 SAVE/EXIT
3.2.5 Reset
Reset all the settings to the default.
3.2.6 EXIT
Exit and Save & exit are selectable.
Move the cursor to , and press OK toSAVE & Exit
save the settings and exit the menu.