Dual-Lens People Counting Camera Quick Start Guide UD14886B-A 0
Dual-Lens People Counting Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Dual-Lens People Counting Camera·Quick Start Guide logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Dual-Lens People Counting Camera·Quick Start Guide APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Dual-Lens People Counting Camera·Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Dual-Lens People Counting Camera·Quick Start Guide supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
Dual-Lens People Counting Camera·Quick Start Guide ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12/24 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
Dual-Lens People Counting Camera·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Dual-Lens People Counting Camera·Quick Start Guide ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. L’utilisation ou le remplacement inadéquats de la pile peuvent entraîner un risque d’explosion. Remplacez-la par le même type ou l’équivalent du même type seulement.
Dual-Lens People Counting Camera·Quick Start Guide Table of Contents 1 Appearance ................................................................................... 10 1.1 Type I for Indoor/Outdoor Scenario .............................. 10 1.2 Type II for Mobile Scenario ............................................ 11 2 Installation .................................................................................... 15 2.1 Type I Camera Installation ............................................. 15 2.
Dual-Lens People Counting Camera·Quick Start Guide 1 Appearance Note: Disassembling the camera without professional technical instruction may affect the accuracy of people counting function. Contact the technical support for repair if any malfunction happens. 1.
Dual-Lens People Counting Camera·Quick Start Guide Table 1-1 Description No. Description 1 Lens 2 IR Cover 3 Front Cover 4 Bottom Cover 5 Mounting Base 6* RJ45 Ethernet interface 7* 12 VDC Power Interface 8 Alarm Interface 9 RS-485 10 Audio Interface 11 Built-in Mic Note: The items marked with * are only supported by certain models. 1.2 Type II for Mobile Scenario This camera type has three cable groups for different models. The following figure shows the cable groups.
Dual-Lens People Counting Camera·Quick Start Guide 6 7 8 9 10 11 12 13 Type A 14 15 2 3 4 5 1 16 Type B 12 13 17 16 Overview Table 1-2 Description No.
Dual-Lens People Counting Camera·Quick Start Guide 8 Back Cover 9 RS-485 10 Audio Interface 11 RJ45 Ethernet interface 12, 13 Alarm Interface 14 CVBS Interface 15 24 VDC Power Interface 16 4-core Aviation Plug 17 Molex Power Plug Note: ● One camera has one cable group. ● The relation between RJ45 wire and M12 wire is shown in the following figure and table.
Dual-Lens People Counting Camera·Quick Start Guide Wire Relation M12 Wire RJ45 Wire TX+ 1 1 TX- 3 2 RX+ 2 3 RX- 4 6 14
Dual-Lens People Counting Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 or 24 VDC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Dual-Lens People Counting Camera·Quick Start Guide Fix the Mounting Base Route the cables. You can route the cables through the side outlet or the ceiling. Route Cables Through Side Outlet Route Cables Through Ceiling Buckle the camera body into the mounting base. Push to get the camera clasped. Fix the Camera Body Fasten the screw to finish.
Dual-Lens People Counting Camera·Quick Start Guide Fasten the Screw 2.2 Type II Camera Memory Card Installation Steps: 1. Loosen the screws to remove the memory card slot cover. Screws Remove the Memory Card Slot Cover 2. Insert the memory card into the slot.
Dual-Lens People Counting Camera·Quick Start Guide Insert the Memory Card 2.3 Type II Camera Installation Steps: 1. Select a suitable mounting position. 2. Paste the drill template.
Dual-Lens People Counting Camera·Quick Start Guide 3. Drill screw holes and plan cable routing. 4. (Optional) If you use expansion screws, screw in the expansion screws 5. Loosen the screws on the side to rotate the camera to the desired angle and fasten the screws. Rotate the Camera 6. Place the spring washer and flat washer into the screw, and then route the screw though the camera and the vehicle ceiling. Fasten the screw to fix the camera. Fix the Camera 7.
Dual-Lens People Counting Camera·Quick Start Guide Fix the Camera 20
Dual-Lens People Counting Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. Wiring Connect the camera to network according to the following figures.
Dual-Lens People Counting Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software.
Dual-Lens People Counting Camera·Quick Start Guide Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Dual-Lens People Counting Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. SADP Interface Note: The SADP software supports activating the camera in batch.
Dual-Lens People Counting Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Dual-Lens People Counting Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Dual-Lens People Counting Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Dual-Lens People Counting Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP and above version Mac OS X 10.8 and above version CPU: 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Mozilla Firefox 30.0-51, Google Chrome 31.0-44, Apple Safari 8.0 and above version Steps: 1. Open the web browser. 2.
Dual-Lens People Counting Camera·Quick Start Guide Note: The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator). 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Download Plug-in 6.
Dual-Lens People Counting Camera·Quick Start Guide Note: For detailed instructions of further configuration, please refer to the user manual of network camera.
Dual-Lens People Counting Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser.
Dual-Lens People Counting Camera·Quick Start Guide Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Dual-Lens People Counting Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Dual-Lens People Counting Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Dual-Lens People Counting Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Dual-Lens People Counting Camera·Quick Start Guide 5.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
0
