Anti-Corrosion Network Bullet Camera Quick Start Guide UD04324B 0504051070109 0
Anti-Corrosion Network Bullet Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Anti-Corrosion Network Bullet Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Anti-Corrosion Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Anti-Corrosion Network Bullet Camera·Quick Start Guide This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Anti-Corrosion Network Bullet Camera·Quick Start Guide This is a class A product. In a domestic environment this product may cause radio inter-ference in which case the user may be required to take adequate measures. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Anti-Corrosion Network Bullet Camera·Quick Start Guide ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
Anti-Corrosion Network Bullet Camera·Quick Start Guide malfunction), and affect the endurance of sensor at the same time. ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
Anti-Corrosion Network Bullet Camera·Quick Start Guide responsibility for problems caused by unauthorized repair or maintenance.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 2 Installation .................................................................................... 13 2.1 Wall Mounting .............................................................. 13 2.2 Junction Box Installation and Wiring ............................. 17 3 Setting the Network Camera over the LAN .................................. 22 3.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 1 Appearance Description XC66 series anti-corrosion network camera has two appearance types, the camera with wiper and the camera without wiper.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Type II without Wiper 3 2 CVBS 1 4 10 5 6 7 CVBS 8 Figure 1-2 Type II Overview Table 1-1 Description of Type I and Type II No. Description No.
Anti-Corrosion Network Bullet Camera·Quick Start Guide No. Description No.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Steps: 1. Install the wall mounting bracket to wall with expansion bolts. Expansion Bolts Figure 2-1 Install Wall Mounting Bracket 2. Unscrew and remove the pedestal from the bracket.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Screws Pedestal Screws Figure 2-2 Remove the Pedestal 3. Align the screw holes on the camera mounting base with those on the pedestal, and fix the camera to the pedestal with screws. Figure 2-3 Fix the Camera to the Pedestal 4. Loosen the fixing screw, and adjust the panning position for the camera. Tighten the fixing screw after adjustment.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Fixing Screw Pan: -45° to 45° Figure 2-4 Adjust Panning Position 5. Adjust the tilting position when fixing the camera to the wall mounting bracket.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Note: Use at least 3 screws on each side of pedestal to fix the camera. Figure 2-6 Fix the Camera 2.2 Junction Box Installation and Wiring Before You Start: Junction box is not included in package. You need to prepare one in advance. The shown junction box below is only for demonstration. Note: Type I and Type II camera follow similar installation procedures. The following demonstration use type I as an example.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Steps: 1. Paste the drill template of the junction box to desired mounting place. Figure 2-7 Drill Template of Junction Box 2. Drill 4 screw holes according to Hole 1 on the template. 3. Insert supplied expansion bolts. Unscrew the nuts and gaskets.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 4. Fix the junction box to wall with nuts and gaskets. 5. Unscrew the junction box cover. Junction Box Cover Figure 2-9 Unscrew the Cover 6. Route the camera cables through the cable hole that is marked with a “Camera” sign on the junction box. Tighten the nut.
Anti-Corrosion Network Bullet Camera·Quick Start Guide CVBS Nut Figure 2-10 Route Camera Cables 7. Route cables of power source, network source, etc. through the other two cable holes of the junction box. Connect the cables.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Camera CVBS Sources Figure 2-11 Fix Wall Mounting Bracket to Wall 8. Tighten the nuts and screw the junction box cover back.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch.
Anti-Corrosion Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Anti-Corrosion Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Anti-Corrosion Network Bullet Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Anti-Corrosion Network Bullet Camera·Quick Start Guide 5.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
0
