Network Bullet Camera Quick Start Guide UD04285B 1
Network Bullet Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Bullet Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Bullet Camera·Quick Start Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Network Bullet Camera·Quick Start Guide Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
Network Bullet Camera·Quick Start Guide ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. Cautions ● Make sure the power supply voltage is correct before using the camera. ● Do not drop the camera or subject it to physical shock. ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
Network Bullet Camera·Quick Start Guide ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details.
Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ................................................................. 9 1.1 Overview ......................................................................... 9 1.2 Micro SD Card Installation ............................................. 10 2 Installation .................................................................................... 12 2.1 Ceiling Mounting ........................................................... 13 2.
Network Bullet Camera·Quick Start Guide 1 Appearance Description 1.1 Overview The overview of the network bullet camera is shown below. 3 4 5 DC12V 6 7 1A G IN ALARM 1B 2 1 VIDEO 9 10 11 13 12 Figure 1-1 Overview Table 1-1 Description No.
Network Bullet Camera·Quick Start Guide No. Description 6 Power Cable Interface 7 Alarm Cable Interface 8 Video Cable Interface 9 Audio Out 10 Audio In 11 Reset Button 12 Micro SD Card Slot 13 Serial Port The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.
Network Bullet Camera·Quick Start Guide Slot Cover Figure 1-2 Remove Card Cover 2. Insert the SD card into the SD card slot. Micro SD Card Figure 1-3 Insert the Card 3. (Optional) Push the inserted micro SD card inside to remove the micro SD card. Re-install the card cover and fasten the two screws to complete the installation.
Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Bullet Camera·Quick Start Guide 2.1 Ceiling Mounting Steps: 1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. 2 1 Ceiling Mounting 1 2 2 1:Screw Hole for Bracket 2:Screw Hole for Mounting Base 1 1 2 Figure 2-1 Drill Template 2. Fix the camera to the wall with the supplied screws.
Network Bullet Camera·Quick Start Guide Please insert the expansion screws first if the camera is mounted to the cement ceiling. And you can use the self-tapping screws directly if camera is mounted to the wooden ceiling. Figure 2-2 Install the Camera 3. Adjust the surveillance angle. 1). Loosen No.1 lock screw to adjust the tilt angle [0 °~100°]. 2). Loosen No.2 lock screw to adjust the pan angle [0°~360°]. 3). Loosen No.3 lock screw to rotate the camera [0°~360°]. 4). Tighten the lock screws.
Network Bullet Camera·Quick Start Guide 2 0°~360° 1 3 0°~360° 0°~100° Figure 2-3 Adjust the Surveillance Angle Figure 2-4 Supplied Wrench 4. (Optional) Install the water-proof jacket for network interface. It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed outdoor. 1). If the network cable has been settled down, cut off the plug of the network cable first. 2).
Network Bullet Camera·Quick Start Guide 3). Insert the water-proof ring into the main body of the water-proof jacket, to increase the sealing ability of the components. 4). Wire the plug and network cables up. 5). Fix the O-ring to the network interface of the camera, and then connect the network cables. 6). Wrap the network interface with the main body of the water-proof jacket, and then rotate the fix nut clockwise to assemble it to the main body of the water-proof jacket.
Network Bullet Camera·Quick Start Guide 2.2 Wall Mounting with a Junction Box Steps: 1. Drill the screw hole and cable hole according to the supplied drill template (shown as Figure 2-1). 2. Align the screw holes of the junction box to the drill template, and fix the junction box to the wall with screws. 3. Route the cables. 4. Fix the camera to the junction box with screws. 5. Adjust the surveillance angle according to step 3 in Chapter 2.1. 6.
Network Bullet Camera·Quick Start Guide 2.3 Wall Mounting with a Gang Box An adapter plate should be purchased separately if you mount the camera to a gang box. Steps: 1. Install the adapter plate to the gang box. 2. Route the cables. 3. Fix the camera to the adapter plate with screws. 4. Adjust the surveillance angle according to step 3 in Chapter 2.1. 5. Install the water-proof jacket according to step 4 in Chapter 2.1.
Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Bullet Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Bullet Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch.
Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Bullet Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Network Bullet Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Bullet Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Bullet Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Bullet Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Bullet Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Bullet Camera·Quick Start Guide 5.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
0
