Network Bullet Camera Quick Start Guide 0
Network Bullet Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Bullet Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Bullet Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Bullet Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Bullet Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
Network Bullet Camera·Quick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be -30 °C to +60 °C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 1.1 Type I Bullet Camera ..................................................... 10 1.2 Type II Bullet Camera .................................................... 11 1.3 Type III Bullet Camera ................................................... 12 1.4 Type IV Bullet Camera ................................................... 13 2 Installation ...................
Network Bullet Camera·Quick Start Guide 5.1.2 Enable Hik-Connect Service via Web Browser .... 40 5.2 Hik-Connect Setup ........................................................ 42 5.3 Add Camera to Hik-Connect .......................................... 42 5.4 Initialize the Memory Card ............................................
Network Bullet Camera·Quick Start Guide 1 Appearance Description 2T camera series has four appearance types. Type I supports no memory card. Type II, Type III and Type IV support memory card function, but the positons of memory card slots on camera are different. 1.1 Type I Bullet Camera 3 DC12VIN 4 5 2 1 Figure 1-1 Overview of Type I Table 1-1 Description of Type I No.
Network Bullet Camera·Quick Start Guide 1.2 Type II Bullet Camera 2 DC12V IN 3 4 1 5 6 Figure 1-2 Overview of Type II Table 1-2 Description of Type II No. Description No.
Network Bullet Camera·Quick Start Guide Note: Use reset button to reset the camera: Press and hold the reset button about 10 s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, and port No., etc. 1.3 Type III Bullet Camera 2 DC12V 3 4 IN 1 5 6 7 Figure 1-3 Overview of Type III Table 1-3 Description of Type III No. Description No.
Network Bullet Camera·Quick Start Guide No. Description No. Description 3 Power Interface 7 Reset Button 4 Network Interface (PoE) Note: Use reset button to reset the camera: Press and hold the reset button about 10 s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, and port No., etc. 1.
Network Bullet Camera·Quick Start Guide 7 8 Figure 1-4 Overview of Type IV Table 1-4 Description of Type IV No. Description No. Description 1 Lens 5 Power Interface 2 Sun Shield 6 Network Interface 3* Alarm Interface 7 Memory Card Slot 4* Audio Interface 8 Reset Button Note: ● The items marked with the "*" are only supported by certain camera models.
Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or PoE (802.3af), please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Bullet Camera·Quick Start Guide Type II Type III Type IV Figure 2-1 Expose Memory Card Slot 2. Insert the memory card.
Network Bullet Camera·Quick Start Guide Type II Memory Card Type III Memory Card Slot Type IV Memory Card Memory Card Slot Reset Button Figure 2-2 Insert Memory Card 3. (Optional) To unmount the memory card, push to get it ejected. 4. Screw the cover back to the camera when installation is finished. 2.2 Type I, II, III Cameras Mounting 2.2.
Network Bullet Camera·Quick Start Guide Steps: 1. Drill 4 screw holes (hole 1 on drill template) and the cable hole in the ceiling/wall. 2 1 Ceiling Mounting Cable Hole 1 2 2 1:Screw Hole for Bracket 2:Screw Hole for Mounting Base 1 1 2 Figure 2-3 Drill Template 2. Fix the camera to the wall/ceiling with the supplied screws. Note: Please insert the expansion screws first if the camera is mounted to the cement wall/ceiling.
Network Bullet Camera·Quick Start Guide 3. Adjust the surveillance angle. 1). Loosen No.1 lock screw to adjust the tilt angle [0 ° to 100°]. 2). Loosen No.2 lock screw to adjust the pan angle [0° to 360°]. 3). Loosen No.3 lock screw to rotate the camera [0° to 360°]. 4). Tighten the lock screws. Note: A wrench is supplied to loosen and tighten the screws.
Network Bullet Camera·Quick Start Guide 4. (Optional) Install the waterproof jacket for network interface. Refer to Section 2.4 Network Cable Waterproof Jacket Installation (Optional). Note: It is recommended to adopt the waterproof jacket (supplied) for the network interface, especially when the camera is installed outdoor. 2.2.2 Mounting with a Junction Box Before You Start: The junction box is not included in the package. You need to prepare one in advance if you adopt this mounting type.
Network Bullet Camera·Quick Start Guide Steps: 1. Paste the drill template to the desired mounting place. Drill the screw hole and the cable hole according to the supplied drill template (shown as Figure 2-3). 2. Align the screw holes of the junction box to the drill template, and fix the junction box to the wall with the screws. 3. Hang the camera with the safety rope of the junction box. 4. Route the cables. 5. Fix the camera to the junction box with the screws. 6.
Network Bullet Camera·Quick Start Guide 2.2.3 Mounting with a Gang Box Before You Start: An adapter plate should be purchased separately if you install the camera to a gang box. Steps: 1. Install the adapter plate to the gang box. 2. Route the cables. 3. Fix the camera to the adapter plate with the screws. 4. Adjust the surveillance angle according to step 3 in Section 2.2. 5. Install the waterproof jacket according to Section 2.4.
Network Bullet Camera·Quick Start Guide 2.3 Type IV Camera Mounting 2.3.1 Wall Mounting Before You Start: Type IV camera supports wall mounting and pendant mounting. The wall mounting bracket is included in the package and the pendant mounting bracket should be purchased separately. Contact your dealer for the recommended models. Steps: 1. Fix the bracket to the wall with the supplied screws. Figure 2-10 Fix the Bracket 2. Install the camera to the bracket with the supplied screws.
Network Bullet Camera·Quick Start Guide Figure 2-11 Install the Camera 2.3.2 Pendant Mounting Steps: 1. Fix the bracket to the ceiling with the supplied screws. Figure 2-12 Fix the Bracket 2. Install the camera to the bracket with the supplied screws.
Network Bullet Camera·Quick Start Guide Adjusting Knob Figure 2-13 Install the Camera 2.3.3 Angle Adjustment 1. Loosen the adjusting screw or adjusting knob to adjust the surveillance angle. 2. Tighten the adjusting screw or adjusting knob.
Network Bullet Camera·Quick Start Guide Tilting: -30° to 15° Panning: 0° to 360° Adjusting Screw Adjusting Knob Tilting: 0° to 90° Panning: 0° to 360° Figure 2-14 Adjust the Angle 2.
Network Bullet Camera·Quick Start Guide Purpose: If the camera is installed outdoor, you can adapt the waterproof accessory for the network cable after the camera is secured on the installation surface. ① ② ③ ④ ⑤ ⑥ Figure 2-15 Waterproof Accessory Components Table 2-1 Components No.
Network Bullet Camera·Quick Start Guide Steps: 1. Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof the rubber gasket ⑤ (rubber gasket inset ridge must face waterproof endcap), and the waterproof endcap ④ in order. 2. Crimp an RJ-45 network plug ③onto the end of the cable, taking care to insert the twisted pairs of wires in correct order. 3. Place the O-type gasket ② onto the end of the camera’s network interface socket ①. 4.
Network Bullet Camera·Quick Start Guide Align the snap and notch. i. Insert ⑤ into ④. ii. Secure ⑥ with ④.
Network Bullet Camera·Quick Start Guide 3 Set the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Bullet Camera·Quick Start Guide 3.2 Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are all supported. We will take activation via SADP software and activation via web browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for activation via client software. 3.2.
Network Bullet Camera·Quick Start Guide Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details. 3. Create and input the new password in the password field, and confirm the password.
Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Bullet Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP.
Network Bullet Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Bullet Camera·Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Bullet Camera·Quick Start Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Bullet Camera·Quick Start Guide 5 Operate via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Bullet Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Bullet Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Add Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Bullet Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Notes: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Bullet Camera·Quick Start Guide 5.4 Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
UD07703B 0
