Network Mini Camera Quick Start Guide 1
Network Mini Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Mini Camera·Quick Start Guide logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Mini Camera·Quick Start Guide LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
Network Mini Camera·Quick Start Guide therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Network Mini Camera·Quick Start Guide Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
Network Mini Camera·Quick Start Guide ● Make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and contact the service center. Cautions ● If the camera fails to synchronize the local time with that of the network, you need to set up the camera time manually.
Network Mini Camera·Quick Start Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be -30°C to +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use. ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture.
Network Mini Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 1.1 Type I, II ......................................................................... 10 1.2 Type III, IV ..................................................................... 12 2 Installation .................................................................................... 15 2.1 Type I, II ...............................................................
Network Mini Camera·Quick Start Guide 1 Appearance Description There are four mini camera appearances available for this camera series, refer to the following chapters for details. 1.
Network Mini Camera·Quick Start Guide 4 1 2 DC12V IN 3 7 6 5 Figure 1-2 Overview of Type II Mini Camera Table 1-1 Description No.
Network Mini Camera·Quick Start Guide No. Description 4 Lens 5 Bracket 6 Complex cable serial interface 7 Reset button Note: Press RESET for 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. You are required to activate the camera after restoring. 1.
Network Mini Camera·Quick Start Guide 2 1 3 4 5 Figure 1-3 Overview of Type III Mini Camera 2 3 4 1 5 Figure 1-4 Overview of Type IV Mini Camera 13
Network Mini Camera·Quick Start Guide Table 1-2 Description No. Description 1 Lens 2 Network interface 3 Reset button 4 Audio interface (line in) 5 Power interface (12 VDC) Note: Press RESET for 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. You are required to activate the camera after restoring.
Network Mini Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or 24 VAC, make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Mini Camera·Quick Start Guide Note: The installation steps for the Type I and the Type II mini cameras are similar. The installation of the Type I is taken as the example in the following instruction. Steps: 1. Fix the camera to the mounting surface with the screws. Figure 2-1 Fix the Camera 2. Adjust the camera position. 1). If you use No.1 screw hole to secure the camera, you can slightly loosen the screw to adjust the camera to the right or the left. 2). If you use No.
Network Mini Camera·Quick Start Guide 1 23 2 1 Figure 2-2 Adjust the Camera Position 3. Loosen the tilt adjust screw to adjust the camera surveillance angel, and tighten the screw if the angle adjust is completed.
Network Mini Camera·Quick Start Guide 2.2 Type III, IV 2.2.1 Ceiling Mounting Note: The installation steps for the Type III and the Type IV mini cameras are similar. Here takes the installation of the Type III as an example to describe the steps. Use the supplied bracket for the ceiling mounting. Steps: 1. Fix the bracket to the mounting surface with screws. Figure 2-4 Fix the Bracket on the Ceiling 2. Fix the camera to the bracket with the screws.
Network Mini Camera·Quick Start Guide 3. Route and connect the camera cables. 4. Loosen the horizontal and vertical adjusting screws to adjust the camera surveillance angel, and then tighten the screws. Horizontal Adjusting Screw Vertical Adjusting Screw Figure 2-6 Adjust the Camera Angle 2.2.2 Wall Mounting Note: The installation steps for the Type III and the Type IV mini cameras are similar. Here takes the installation of the Type IV as an example to describe the steps.
Network Mini Camera·Quick Start Guide 2. Install the camera to the wall with the screws. Figure 2-8 Install the Camera to the Wall 3. Route and connect the camera cables. 4. Refer to step 4 in 2.2.1 to adjust the camera angle.
Network Mini Camera·Quick Start Guide 3 Set the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Mini Camera·Quick Start Guide 3.2 Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are all supported. We will take activation via SADP software and activation via web browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for activation via client software. 3.2.
Network Mini Camera·Quick Start Guide Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Mini Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch.
Network Mini Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Mini Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP.
Network Mini Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Mini Camera·Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and later versions CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and later versions, Apple Safari 5.0.2 and later versions, Mozilla Firefox 5.0 and later versions and Google Chrome 18 and later versions Steps: 1. Open the web browser. 2.
Network Mini Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Mini Camera·Quick Start Guide 5 Operate via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Mini Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Mini Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 3. Select Hik-Connect form the Platform Access Mode drop-down list. 4. Check Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Mini Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Add Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Mini Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Mini Camera·Quick Start Guide 5.4 Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. Then you can start recording in the camera such as the video triggered by motion detection.
UD08619B 0
