Network Dome Camera Quick Start Guide U D04291B 1
Network Dome Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Dome Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Dome Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Dome Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Dome Camera·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network Dome Camera·Quick Start Guide according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
Network Dome Camera·Quick Start Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C to +60°C, or -40°C to +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use.
Network Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 1.1 Type I Camera ............................................................... 11 1.1.1 Overview ............................................................ 11 1.1.2 Cable Description ............................................... 13 1.2 Type II Camera .............................................................. 14 1.2.1 Overview ........................
Network Dome Camera·Quick Start Guide 4 Accessing via Web Browser .......................................................... 51 5 Operating via Hik-Connect App .................................................... 53 5.1 Enable Hik-Connect Service on Camera ......................... 53 Enable Hik-Connect Service via SADP Software .. 53 Enable Hik-Connect Service via Web Browser .... 54 5.2 Hik-Connect Setup ........................................................ 56 5.3 Adding Camera to Hik-Connect .........
Network Dome Camera·Quick Start Guide 1 Appearance Description This series of cameras has two appearance types. 1.1 Type I Camera Type I camera has different models. Some models have the lens that zoom and focus levels must be manually adjusted via zoom/focus lever and some models have a motor-driven lens that zoom and focus adjustment can be completed via web browser or client software. Please refer to the actual device. 1.1.1 Overview The overview of the Type I network dome camera is shown below.
Network Dome Camera·Quick Start Guide 5 8 6 7 Figure 1-2 Overview of Type I Camera (2) Table 1-1 Overview of Type I Camera No.
Network Dome Camera·Quick Start Guide 1.1.2 Cable Description Cable description of the Type I network dome camera is shown below. Note: Cables vary according to different models as the figures below.
Network Dome Camera·Quick Start Guide Table 1-2 Cable Description No. Description 9 Network Interface 10 Power Supply Interface 11 Audio/Alarm Interface 12 Audio Input and Output Interface 13 Video Output Interface 14 Alarm Input and Output Interface Notes: Power on the camera when pressing the RESET button, and press button for another 10 seconds to restore the default settings, including the user name, password, IP address, port No., etc.
Network Dome Camera·Quick Start Guide 1.2.1 Overview The overview of the Type II network dome camera is shown below.
Network Dome Camera·Quick Start Guide Overview of Type II Camera No. Description 1 Bubble 2 Black Liner 3 Lens 4 Reset 5 Memory Card Slot 1.2.2 Cable Description Cable description of the Type II network dome camera is shown below. Note: Cables vary according to different models as the figures below.
Network Dome Camera·Quick Start Guide DC12V I N 6 7 8 Figure 1-8 Cable Description of Type II Camera (2) Table 1-4 Cable Description No. Description 6 Power Supply Interface 7 Network Interface 8 Video Output Interface Note: Power on the camera when pressing the REST button, and press button for another 10 seconds to restore the default settings, including the user name, password, IP address, port No.
Network Dome Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or PoE (802.3af). Make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Dome Camera·Quick Start Guide Preparation Purpose: Before mounting, you have to disassemble the camera and install the memory card first. 2.1.1 Disassembling Steps: 1. Loosen the three screws on the edge of the bubble with the screw driver. 2. Lift and put aside the bubble. 3. Remove the inner black liner.
Network Dome Camera·Quick Start Guide Black Liner Bubble Screws Remove the Bubble and Black Liner (Type II Camera) 2.1.2 Memory Card Installation Steps: 1. Rotate the camera body to completely expose the memory card slot. 2. Insert the memory card into the memory card slot, and push to get it mounted.
Network Dome Camera·Quick Start Guide Memory Card Memory Card Slot Install the Memory Card (Type I Camera) Memory Card Slot Install the Memory Card (Type II Camera) 3. (Optional) To unmount the memory card, push to eject it.
Network Dome Camera·Quick Start Guide Mounting Installation of type I camera, and type II camera are similar. We take type I camera as an example in this manual. 2.2.1 Ceiling Mounting Steps: 1. Attach the drill template (supplied) to the place where you want to fix the camera. 2. Drill three screw holes and cable hole (optional) in the ceiling according to the drill template.
Network Dome Camera·Quick Start Guide Front Drill Template Hole A: Route cables through the ceiling. Hole B: Side outlet. Hole 1: Fix the mounting base. Please use Φ5.5mm drill to install expansion screws. The Drill Template (Type II Camera) Notes: ● The drill template varies according to the different camera models as the figures below. Please refer to the actual device. ● If you want to route the cables inside the ceiling, drill a cable hole in the ceiling according to the drill template.
Network Dome Camera·Quick Start Guide Back Box Screws Secure the Camera 4. Adjust the surveillance angle, zoom and focus level. Refer to the Chapter 2.3 Image and Focus Adjusting for detailed information. 5. Install the inner black liner back to the camera. 6. Install the bubble back to the camera and secure it with screws.
Network Dome Camera·Quick Start Guide Conduit Installation on the Side If you want to route the cables from side of the camera, you need to install a conduit for cable routing. Steps: 1. Rotate the water-proof plug counterclockwise to remove it from the camera. Side Cable Outlet Water-proof Plug Remove the Water-proof Plug 2. Route the cables through the side outlet to the conduit. 3. Align and rotate the conduit clockwise to the side outlet tightly.
Network Dome Camera·Quick Start Guide Note: For wall mounting, position the side outlet directly downward for waterproofing. Downward Side Outlet Direction 2.2.2 In-ceiling Mounting Before you start: In-ceiling mounting bracket is not included in package. If you choose this mounting type, you have to prepare a bracket first. The in-ceiling mounting bracket shown in below is only for demonstration. Steps: 1. Cut a hole in the ceiling according to the size of the in-ceiling mounting bracket.
Network Dome Camera·Quick Start Guide Main Body Ceiling Hole Size Rim In-ceiling Mounting Bracket Cut a Hole for In-ceiling Mounting 2. Align No.1 screw holes with the corresponding screw holes on the bracket, and secure the mounting base to the bracket with screws. In-ceiling Mounting Bracket Mounting Base No.1 Screw Holes Install Mounting Base 3. Align the screw holes for camera fixing, and secure the camera to the mounting base.
Network Dome Camera·Quick Start Guide In-ceiling Mounting Bracket Mounting Base Camera Screw Holes for Camera Fixing Install the Camera to the Mounting Base 4. Place the bracket and camera to the hole in ceiling, and screw the toggle bolt clockwise to fix the bracket in ceiling.
Network Dome Camera·Quick Start Guide Toggle Bolts: screw them clockwise Toggle Bolts: fix the bracket Fix the Bracket in Ceiling 5. Adjust the surveillance angle, and refer to Chapter 2.3 Image and Focus Adjusting for details. 6. Install the black liner and the bubble back to the camera.
Network Dome Camera·Quick Start Guide 7. Install the rim to the bracket. Rim Rim Install the Rim 2.2.3 Mounting with Wall Mounting Bracket Before you start: Wall mounting bracket is not included in package. If you choose this mounting type, you have to prepare a bracket first. The wall mounting bracket shown below is only for demonstration. Note: When choosing a wall mounting bracket, you must pay attention to the size of the cap which should match the mounting base of the camera.
Network Dome Camera·Quick Start Guide Steps: 1. Route the cables, install the wall mounting bracket, and secure the cap on the bracket. Wall Mounting Bracket Cap Install Wall Mounting Bracket 2. Align the screw holes of the mounting base with the corresponding screw holes of the cap. 3. Secure the mounting base to the cap with screws.
Network Dome Camera·Quick Start Guide 4. Align the camera with the mounting base, and secure the camera with screws. Secure the Camera 5. Connect the video output connector to the monitor. Connect the power connector to the power supply. 6. Adjust the image and focus. Refer to the Chapter 2.3Image and Focus Adjusting for more detailed information. 7. Install the inner black liner back to the camera. 8. Secure the bubble to the camera with screws.
Network Dome Camera·Quick Start Guide Secure Black Liner and Bubble 2.2.4 Mounting with Pendant Mounting Bracket Before you start: Pendant mounting bracket is not included in package. If you choose this mounting type, you have to prepare a bracket first. The pendant mounting bracket shown below is only for demonstration. Note: When choosing a pendant mounting bracket, you must pay attention to the size of the cap which should match the mounting base of the camera.
Network Dome Camera·Quick Start Guide Size of the Mounting Base Steps: 1. Route the cables and Install the pendant mounting bracket. Secure the cap on the bracket. Pendant Mounting Bracket Cap Install the Pendant Mounting Bracket 2. Align the screw holes of the mounting base with the corresponding screw holes of the cap. 3. Secure the mounting base to the cap with screws.
Network Dome Camera·Quick Start Guide Cap Mounting Base Install the Mounting Base 4. Align the camera with the mounting base, and secure the camera with screws. Secure the Camera 5. Adjust the image and focus. Refer to the Chapter 2.3 Image and Focus Adjusting for more detailed information.
Network Dome Camera·Quick Start Guide 6. Install the inner black liner back to the camera. 7. Secure the bubble to the camera with screws. Secure Black Liner and Bubble 2.2.5 Mounting with Junction box Steps: 1. Install the junction box in the ceiling or the wall. 2. Attach the mounting base to the junction box with screws.
Network Dome Camera·Quick Start Guide Install the Mounting Base 3. Route the cables through the hole in the center of the mounting base. 4. Align the camera with the mounting base. And secure the camera with screws. Secure Camera 5. Adjust the image and focus. Refer to the Chapter 2.3 Image and Focus Adjusting for more detailed information. 6. Install the inner black liner back to the camera. 7. Secure the bubble to the camera with screws.
Network Dome Camera·Quick Start Guide Secure the Black Liner and Bubble 2.3 Image and Focus Adjusting Before you start: Connect the camera to a monitor with supplied auxiliary video output cable, and power on the camera.
Network Dome Camera·Quick Start Guide Note: For certain camera models, the auxiliary video cable is not included in the package. Instead, you can connect the video out interface of the camera to a monitor for image and focus adjustment. Video Out Interface Video Out Interface of the Camera 2.3.1 3-Axis Adjustment Steps: 1. View the camera image using the monitor. 2.
Network Dome Camera·Quick Start Guide Pan: 0° to 355° Tilt: 0° to 90° Rotate: 0° to 355° 3-axis Adjustment (Type I Camera) Tilt: 0° to 70° Pan: 0° to 355° Rotate: 0° to 355° 3-axis Adjustment (Type II Camera) 40
Network Dome Camera·Quick Start Guide 2.3.2 Zoom and Focus Adjustment. Manually Adjustment: Some camera models of this series have the lens that zoom and focus levels must be manually adjusted via zoom/focus lever and you can use zoom lever and focus lever to adjust the lens. Steps: 1. View the camera image using the monitor. 2. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the appropriate angle of view.
Network Dome Camera·Quick Start Guide Zoom/Focus Lever Zoom/Focus Lever (Type II Camera) 3. Tighten the zoom lever. 4. Loosen the focus lever and move the lever between F (Far) and N (Near) to obtain the optimum focus. 5. Tighten the focus lever. Motor-driven Lens: Some camera models of this series are equipped with a motor-driven lens. You can adjust the zoom and focus level on PTZ control panel by visiting the camera via web browser or client software.
Network Dome Camera·Quick Start Guide Zoom and Focus Adjustment via Web Browser 43
Network Dome Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. Wiring Connect the camera to network according to the following figures.
Network Dome Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software.
Network Dome Camera·Quick Start Guide Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Dome Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. SADP Interface Note: The SADP software supports activating the camera in batch.
Network Dome Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Dome Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Network Dome Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Dome Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Dome Camera·Quick Start Guide 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Dome Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser.
Network Dome Camera·Quick Start Guide Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Dome Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Dome Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Dome Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Dome Camera·Quick Start Guide 5.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
Network Dome Camera·Quick Start Guide 59