User's Manual

ManualsBrandsHIKVISION ManualsCamera & PhotoDashCam

D Parts Introduction E Installation F Mobile Phone Connection G Basic Description

H Cautions

I Troublshooting

H Troubleshooting

Model

Aperture

Pixel

Max. Resolution

Angle

Screen

Storage

G-Sensor

Wi-Fi

Sound Recording

Power Supply

Power Consumption

Operating Temperature and Humidity

Installation Type

Dimensions (L × W × H)

Weight

AE-DC8322-G2PRO

F1.75

2160P (3840*2160); 1080P (1920*1080)

2160P @ 25fps

Horizontal: 113°, Diagonal: 135°

3”

EMMC + TF card, EMMC: 64G/128G/256G TF Card: 32 GB to 128 GB

Built-in, collision triggered recording and recording lock

Yes

5 VDC, 2 A

Approx. 6 W

-20 °C to 65 °C (-4 F to 158 F). Humidity 95% or less.

General

100 × 85 × 38 mm (3.6ʺ × 3.5ʺ × 2.8ʺ)

Approx. 150 g (0.25 lb.)

Scan QR Code

Specications

Clean the windshield and

paste the electrostatic lm

onto it.

Avoid introducing air bubble.

DO NOT paste the lm

repeatedly.

Paste the device onto the

electrostatic lm and route

cable to the disater box for

power supply.

Connect the power cord as

the gure above.

Adjust the angle to the

target direction.

Scan the QR code to download and

install HikDashcam app.

Add the dashcam to the app.

a. Run the HikDashcam app.

b. Tap Wi-Fi Connection.

c. In Wi-Fi list, select the Wi-Fi SSID

of the target dashcam and enter

Wi-Fi password to build

connection.

• You can set the parameters of the

dashcam.

• For iOS, you need to go to Wi-Fi

settings of your phone to connect

to the Wi-Fi of dashcam.

Edit the dashcam password to

activate it to avoid abnormal

recording after connecting to Wi-Fi.

Dashcam Wi-Fi default parameters:

• Wi-Fi SSID: HIKVISION-XXXX

(XXXX refers to the last four

characters of verication code.)

• Wi-Fi password: 1234567890

(please edit password after logging in

for the rst time.)

Start Up

Connect the power cord to the car battery.

Device starts recording automatically once the car started.

Bluetooth Remote Control

You can start recording and capturing via bluetooth remote control after

connect to bluetooth.

Press the capture button to capture and save a picture.

Linkage Recording: Once enabled, a 12-second video involving 6 s before

and 6 s after the capture will be saved.

Remote-Control Installation: it's suggested to install the remote control to

where you can operate easily, such as the underside of steering wheel.

Other Parameters

Check the device and SW version at System Settings -> About.

Set resolution at Video Recording.

Turn on/off WDR/Distortion Correction in Image Parameter. It's

suggested to open WDR when against the light.

Format SD Card: Clear the data in the SD card.

After G-Sensor enabled, device makes a video once the car has an

emergent brake or turn.

Set the Calibration Line

Adjust the calibration line to improve the veracity of ADAS.

Step1: Park the car to an open eld.

Step2: Slide right to open the calibration interface

Step3: Adjust the angle of the lens make the calibration line coincide

with the the horizon line.

Tips for Dashcam

• Use the original power cord in the package for power supply.

• Dashcam supports to record and save vehicle accident recordings,

but doesn't guarantee to record all the accidents.

• Operate the dashcam in accordance with the local regulations and

laws.

• Save the user manual properly for future reference.

• In case the dashcam is directly connected with the automobile power

system, you are recommended to power off the dashcam when the

automobile is off.

• Working temperature: [-20 C, +65 C ] ([-4 F, 149 F]). To protect the

dashcam, do not use it in high-humidity and high-dust density

environment and keep all liquids away from it.

• The user manual is subject to the dashcam update.

Tips for TF Card

• For the stability and efficiency of data storage, Please purchase TF

cards from offical channels. It is recommended to use a high-speed TF

card of class 10 or above, and its capacity should be no less than 16 G.

• Shut down the device before installing and uninstalling the TF card.

• It is recommended to format the TF card once a month.

• Please replace the TF card regularly to avoid the TF card exceeding

its service life and unable to store data.

Device supports live view.

Slide horizontally to change the channel(with 2 cameras connected.)

Slide down at the main page to turn on/off the Wi-Fi, bluetooth, GPS,

speaker and recording.

Tap the screen and slide left to display the main menu. You can check

video, image or set parameters.

Trouble Solution SolutionTrouble

The dashcam drops

easily.

Starting the dashcam

failed.

The dashcam powers

o easily.

Recording is

abnormal and

indicator is unlit.

Recording is blurred.

Recording is mute.

Dashcam reboots

itself.

Clean the windshield before installation.

Check whether the vehicle is started and power

supply is normal.

Check whether the car charger is tightly connected.

Restore to defaults: hold the RESET button until the

startup music is heard.

Make sure the power cord is in good condition.

Make sure the power cord is tightly connected to the

according interfaces.

Make sure that the dashcam started up successfully.

Check whether the TF card is inserted.

Check the status of TF card, e.g. its format, its lifespan.

Change TF card if it is not well.

Make sure the protective lm is peeled o.

Check whether the windshield or the lens of dashcam

is blurred.

Set audio settings on the device or turn on sound

recording in HikDashcam app.

Check whether the car charger is equipped with power

supply interface of 5 VDC, ≥ 2 A.

The mobile phone

cannot display

recordings.

It may be relevant with the player or system of the

phone. Please connect TF card to your computer and

display the recordings.

TF card is not

detected when you

connect dashcam to

computer with the

supplied power cord.

Dashcam does not support data transmission and the

supplied power cord is only for charging.

If you need to transfer data, please connect TF card

to your computer.

Wi-Fi connection

takes a long time.

It may be caused by the interferrence of the

surrounding Wi-Fi signals. Please use the dashcam in

an environment of less interferrence.

Shut down unnecessary programs in your phone to

release some resources for HikDashcam app and

reconnect Wi-Fi.

Dashcam Wi-Fi

password is forgotten.

The default password is 1234567890. If you have

revisied the password, regain the password by the

following steps.

1. Hold the RESET button on dashcam until the startup

music is heard and the dashcam is restored to

defaults.

2. Go to Wi-Fi Connection interface in HikDashcam

app.

3. Select Wi-Fi SSID and log in with default password

1234567890.

Access to

Micro USB

Check whether the car charger is tightly connected.

13 14

Check whether the 3M tape is tightly sticked to the

electrostatic lm before the installation.

Turn on sound through the the audio control function

of the dashcam.

Mobile phone cannot

connect to dashcam.

Make sure HikDashcam app is installed.

Please restart the dashcam to the app.

No GPS signal.

Check whether the GPS function is enabled.

Normally, the GPS function is enabled by default.

Make sure the device is not in the places of weak

signal or no signal, such as underground garage.

· Make sure there is no metal around the device

because metal will interfere with GPS signal.

Make sure the location where the device is installed is

not pastd with radiation protection lm. The lm will

interfere with GPS signal.

Disater box

1. TF Card Slot

Install TF card to record.

2. RESET Button

Press RESET button during

powering on to restart the

device.

3. Parked Monitoring Indicator

After turning off the vehicle, the

indicator keeps red and the car is

in the parked monitoring mode.

5. Mini USB Interface

Access to 4G module/Data

transmission

6. Micro USB Interface

Access to electrostatic film

for powering supply.

7. TVI Camera Interface

8. MIC

Microphone

10. Audio Output

9. Power/Status Indicator

It keeps red during powering on.

It keeps blue when the device works properly.

4. Camera

(Opertional) Install TVI camera and connect to the device according to

specic manual. Slide the device along the arrow in step 4 to remove.

When the car is off, device turns into parked monitoring mode and start to record

once the current scene changed or collision happened.

Avoid the airbag when installing the remote control for your safety.

Option2: Connect the device to 4G network, device detects the latest

SW version. You can download and update accordingly. (It needs to

compatible with 4G module).

Update

Option1: Through Hikdashcam APP

Step1: Power on the device and open Wi-Fi to connect the APP.

Step2: Check the latest SW version in the APP.

Step3: Choose System Settings -> SW Update to start update.

Step4: Device restarts once the rmware started.