User's Manual

D Parts Introduction E Installation F Mobile Phone Connection G Function Description
7
H Cautions
8
I Troublshooting
9
H Troubleshooting
10
11
12
Model
Aperture
Pixel
Max. Resolution
Angle
Screen
Storage
G-Sensor
Wi-Fi
Sound Recording
Power Supply
Power Consumption
Operating Temperature and Humidity
Installation Type
Dimensions (L × W × H)
Weight
AE-DC8312-C6S
F1.75
8 MP
4 K@ 25fps
135°
3”
TF card, 32 GB to 128 GB
Built-in, collision triggered recording and recording lock
Yes
Yes
5 VDC, 2 A
Approx. 3.5 W
-20 °C to 70 °C (-4 F to 158 F). Humidity 95% or less.
General
90 × 88 × 70 mm (3.6ʺ × 3.5ʺ × 2.8ʺ)
Approx. 125 g (0.25 lb.)
Scan QR Code
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Specications
1
3
Clean the windshield and
paste the electrostatic lm
onto it.
Avoid introducing air bubble.
DO NOT paste the lm
repeatedly.
Peel o the release paper of
3M tape and install the
dashcam onto the center of
the electrostatic lm. Connect
the dashcam with one end of
the power cord along the red
line shown in gure.
Connect the other end of
power cord to the car
charger and connect car
charger to cigarette lighter.
Adjust the surveillance angle
and the installation is
completed. The tilt adjusting
angle is from -10° to 10°.
Scan the QR code to download and
install HikDashcam app.
Add the dashcam to the app.
a. Run the HikDashcam app.
b. Tap Wi-Fi Connection.
c. In Wi-Fi list, select the Wi-Fi SSID
of the target dashcam and enter
Wi-Fi password to build
connection.
• You can set the parameters of the
dashcam.
• For iOS, you need to go to Wi-Fi
settings of your phone to connect
to the Wi-Fi of dashcam.
Edit the dashcam password to
activate it to avoid abnormal
recording after connecting to Wi-Fi.
1
Dashcam Wi-Fi default parameters:
• Wi-Fi SSID: HIKVISION-C6PRO-XXXX
(XXXX refers to the last four
characters of verication code.)
• Wi-Fi password: 1234567890
(please edit password after logging in
for the rst time.)
Power On and Power O
Power On: When you start up the engine, the dashcam powers on.
Power O: When you turn o the engine, the dashcam powers o.
Recording
Two recording types are provided: Normal Reording and Emergency
Recording. Sound and mute recordings are selectable. Sound recording is set
as default. You can set audio settings on the device or turn o sound
recoding in app.
Safety Instruction
These instructions are intended to ensure that users can use the product
correctly to avoid danger or property loss.
Cautions: Injury or equipment damage may occur if any of the cautions are
neglected.
• In the use of the dashcam, you must be in strict compliance with the local
laws and regulations.
• You are recommended to install the dashcam on the location of rear
mirror to ensure the dashcam can record with the best surveillance view.
DO NOT install the dashcam on the location that will block the driver’s sight.
• Keep the user manual properly for future reference. See initial
connection of dashcam in user manual.
• Purchase the TF card from legal channel. To ensure safe and
stable data transmission, it is recommended to use TF card of
Class 10 or above.
• Format the new TF card rst before using the card.
• To protect TF card from damage, shut down the dashcam before
installing and uninstalling TF card.
• If the dashcam is directly connected with the vehicle power
system, you are recommended to power o the dashcam when
the engine is o. Disconnect cigarette lighter to avoid insucient
voltage and abnormal startup. Reconnect cigarette lighter to
ensure dashcam work normally when you start the car again.
• Operating temperature is from -20 C to 70 C (-4 F to 158 F). To
protect the dashcam, DO NOT use it in high temperature, low
temperature, or high-humidity environment. Keep the dashcam
from rain and dust.
• The manual is subject to update. The functions of dashcam may
vary according to dierent models.
*The driving assistance function of the device only sends alarm or warning to
the driver and cannot replace the driver’s judgement and operation. With the
device, you also should drive carefully to avoid trac accident or violation.
Pedestrian or object recognition failure or recognition error may occur due to
external factors. DO NOT overly rely on the driving assistance function.
Trouble Solution SolutionTrouble
The dashcam drops
easily.
Starting the dashcam
failed.
The dashcam powers
o easily.
Recording is
abnormal and
indicator is unlit.
Recording is blurred.
Recording is mute.
Dashcam reboots
itself.
Clean the windshield before installation.
Check whether the vehicle is started and power
supply is normal.
Check whether the car charger is tightly connected.
Restore to defaults: hold the RESET button until the
startup music is heard.
Make sure the power cord is in good condition.
Make sure the power cord is tightly connected to the
according interfaces.
Make sure that the dashcam started up successfully.
Check whether the TF card is inserted.
Check the status of TF card, e.g. its format, its lifespan.
Change TF card if it is not well.
Make sure the protective lm is peeled o.
Check whether the windshield or the lens of dashcam
is blurred.
Set audio settings on the device or turn on sound
recording in HikDashcam app.
Check whether the car charger is equipped with power
supply interface of 5 VDC, ≥ 2 A.
The mobile phone
cannot display
recordings.
It may be relevant with the player or system of the
phone. Please connect TF card to your computer and
display the recordings.
TF card is not
detected when you
connect dashcam to
computer with the
supplied power cord.
Dashcam does not support data transmission and the
supplied power cord is only for charging.
If you need to transfer data, please connect TF card
to your computer.
Wi-Fi connection
takes a long time.
It may be caused by the interferrence of the
surrounding Wi-Fi signals. Please use the dashcam in
an environment of less interferrence.
Shut down unnecessary programs in your phone to
release some resources for HikDashcam app and
reconnect Wi-Fi.
Dashcam Wi-Fi
password is forgotten.
The default password is 1234567890. If you have
revisied the password, regain the password by the
following steps.
1. Hold the RESET button on dashcam until the startup
music is heard and the dashcam is restored to
defaults.
2. Go to Wi-Fi Connection interface in HikDashcam
app.
3. Select Wi-Fi SSID and log in with default password
1234567890.
1
2
3
Power Cord
Car Charger
Cigarette
Lighter
• The power mode of cigarette lighter may vary by dierent vehicle
types. Some may be powered constantly. In this case, please
make sure that the dashcam stops after you turn o the vehicle
engine. Otherwise, insucient voltage may occur to vehicle battery.
• Make sure you have connected the dashcam to power according to
Step 2 and Step 3 in Installation section.
·
Check whether the car charger is tightly connected.
13
4
0°
10°
-10°
·
Check whether the 3M tape is tightly sticked to the
electrostatic lm before the installation.
·
Turn on sound through the the audio control function
of the dashcam.
10
·
·
Mobile phone cannot
connect to dashcam.
Make sure HikDashcam app is installed.
Please restart the dashcam to the app.
No GPS signal.
·
·
Check whether the GPS function is enabled.
Normally, the GPS function is enabled by default.
Make sure the device is not in the places of weak
signal or no signal, such as underground garage.
· Make sure there is no metal around the device
·
because metal will interfere with GPS signal.
Make sure the location where the device is installed is
not pastd with radiation protection lm. The lm will
interfere with GPS signal.
2
1. RESET Button
(Restore the device to defaults.)
2. TF Card Slot
3. Lens
4. Microphone
5. Speaker
6. Power Interface
7. MicroUSB Interface
(It can be extended as 4G
interface.)
8. Screen
9. Buttons